mcb.dk | Få success online

Heatmiser UH4 4 Zone 230V Wiring Centre

Heatmiser UH4 4 Zone 230V Wiring Centre Product Part Number UH4 4 Zone 230V Wiring Centre - CON0135 Description The Heatmiser UH4 can be used in conjunction with our mains thermostats. The UH4 is also ideally suited for underfloor heating. When used for under-floor heating an option is available to use zone 4 for conventional radiator control. The UH4 provides central switching of up to 4 zone actuators output for a hot water cylinder and the system boiler and pump. Key Features Controls up to 4 heating zones Supply: 230v AC 50Hz 1 Phase IP Protection: IP20 Installed Dimensions: (L)384 x (H)148 x (D)60mm For use with Heatmiser 230v thermostats Output for a hot water cylinder and the system boiler and pump

GBP 67.18

1

Nuaire ECO MEV

Nuaire ECO MEV Product Part Number MEV-ECO - ECO MEV-ECO with humidity sensor - ECO-H Description The MEV-ECO is a centralised extract system capable of extracting air from multiple wet rooms in a property. The unit offers the latest in low-watt DC fans, combining AC supply and DC voltages to bring you an extract fan that is both high powered and energy-efficient. The MEV-ECO provides quiet operation with reduced power consumption, low SFPs, and high airflow rates. At only 125mm deep, the unit saves space and ventilates up to 100 l/s. These MEV units are SAP recognised and have been designed to meet the most current building regulations, both Part F and Part L.

GBP 413.64

1

Vent Axia Lo-Carbon Sentinel Multivent

Vent Axia Lo-Carbon Sentinel Multivent The top of the range Sentinel Multivent continuous mechanical extract ventilation range is designed for the simultaneous extraction of up to several bathrooms/ Wet Rooms to a centrally positioned unit normally installed in the attic space Complete DIY Kit of a Vent Axia multiple room extraction unit with in insulated Flexible Ducting and fittings suitable for extraction of 4 separate areas Our Comprehensive DIY Kits have everything you should require to install the system to building control regulations Please note - You can purchase the MEV unit with or without the ductwork on this listing Key Unit Features Integral LCD display allows the installer to select appropriate low, normal and boost speeds to meet demand Energy efficient EC/DC motors - 1/3 less energy lost to heat than a conventional AC motor Ultra-quiet - acoustically lined for low noise levels Manual and automatic control options Integral adjustable overrun timer and delay on timer Option of wall, ceiling, and loft mounting Fully serviceable unit with all parts accessible PVC outer casing with an acoustic lining is included as standard, ensuring minimum noise levels Technical Features Max Airflow of 450m3/h Best in class Specific Fan Power (SFP) as low as 0.16 wls Dimensions (mm) 340 long x 310 wide x 249 high Fitted with four extract 125 or 100mm diameter spigots allowing quick connection to ducts Demand Control - enables precise ventilation rate, is set in 1% increments based on property size Plug-n-Play automatic sensor detection Switched live and SELV connections Dry Out setting – Option set at installation, Sentinel Multivent will run on boost for 1 week to assist in removing moisture Optional Wireless Control – up to 4 controllers on any one system Recognised in SAP Appendix Q Complies with Building ADF (System 3) Energy efficient EC/DC motors - 1/3 less energy lost to heat than a conventional AC motor 2-year standard or optional 5-year parts warranty Controllability Demand Control - enables precise ventilation rate, is set in 1% increments based on property size

GBP 487.87

1

Heatmiser UH8 230v 8 Zone Wiring Centre

Heatmiser UH8 230v 8 Zone Wiring Centre Product Part Number UH8 230v 8 Zone Wiring Centre - CON0148 Description The Heatmiser UH8 underfloor heating wiring centre is designed to work with our 4 channel 230v time clock (TM4) and 230v Set back thermostat (DS-SB) but equally could be used with any 230v room thermostat. Up to 8 zones can be controlled from the UH8. On board the UH8 are two heating time channels, each zone allows you to specify which time channel it should follow. 2 additional time channel connections are provided for hot water control or other auxiliary devices. On demand from any zone, a 230v output is provided to switch the relevant zone actuator, underfloor heating pump and valve. A volt free connection is supplied for the boiler, making it compatible with almost all types of boilers. A simple slide switch makes zone 8 suitable for controlling a radiator zone. When used for controlling radiators, zone 8 does not enable the underfloor heating pump, valve and boiler.Up to 4 actuators can be connected to each zone. Key Features Controls up to 8 heating zones Supply: 230v AC 50Hz 1 Phase IP Protection: IP20 Installed Dimensions: (L)384 x (H)148 x (D)60mm For use with Heatmiser 230v thermostats

GBP 79.84

1

Heatmiser UH8 RF 230v 8 Zone Wiring Centre

UH8 RF 230v 8 Zone Wiring Centre Product Part Number UH8 RF 230v 8 Zone Wiring Centre - CON0149 Description The Heatmiser UH8 underfloor heating wiring centre is designed to work with our 4 channel 230v time clock (TM4) and 230v Set back thermostat (DS-SB) but equally could be used with any 230v room thermostat. Up to 8 zones can be controlled from the UH8. On board the UH8 are two heating time channels, each zone allows you to specify which time channel it should follow. 2 additional time channel connections are provided for hot water control or other auxiliary devices. On demand from any zone, a 230v output is provided to switch the relevant zone actuator, underfloor heating pump and valve. A volt free connection is supplied for the boiler, making it compatible with almost all types of boilers. A simple slide switch makes zone 8 suitable for controlling a radiator zone. When used for controlling radiators, zone 8 does not enable the underfloor heating pump, valve and boiler.Up to 4 actuators can be connected to each zone. Key Features Controls up to 8 heating zones Supply: 230v AC 50Hz 1 Phase IP Protection: IP20 Installed Dimensions: (L)384 x (H)148 x (D)60mm For use with Heatmiser 230v thermostats

GBP 145.19

1

Vent Axia Sentinel Multivent H Unit

Vent Axia Sentinel Multivent H Unit Product Part Number Vent Axia Sentinel Multivent with Humidity Sensor - 445655 Key Features Internal Humidity sensor Integral LCD display allows the installer to select appropriate low, normal and boost speeds to meet demand Ultra-quiet - acoustically lined for low noise levels Demand Control - enables precise ventilation rate, is set in 1% increments based on property size Manual and automatic control options Integral adjustable overrun timer and delay on timer Plug-n-Play automatic sensor detection Switched live and SELV connections PVC outer casing with an acoustic lining is included as standard, ensuring minimum noise levels Technical Features Max Airflow of 450m3/h Energy efficient EC/DC motors - 1/3 less energy lost to heat than a conventional AC motor Best in class Specific Fan Power (SFP) as low as 0.16 wls Dimensions (mm) height 310mm, width 360mm, depth 260mm Fitted with four extract 125 or 100mm diameter spigots allowing quick connection to ducts Option of wall, ceiling, and loft mounting Fully serviceable unit with all parts accessible Dry Out setting – Option set at installation, Sentinel Multivent will run on boost for 1 week to assist in removing moisture Recognised in SAP Appendix Q Complies with Building ADF (System 3) 2-year standard or optional 5-year parts warranty Humidity Sensor The integral humidity sensor (Sentinel Multivent H) increases fan speed in proportion to relative humidity levels, saving energy and reducing noise The sensor also reacts to small but rapid increases in humidity, even if the normal trigger threshold is not reached. This unique feature ensures adequate ventilation, even for the smallest wet room Night-time relative humidity increment setback feature suppresses nuisance tripping as humidity gradually increases with falling temperature Controllability Demand Control - enables precise ventilation rate, is set in 1% increments based on property size Integral LCD display allows the installer to select appropriate low, normal and boost speeds to

GBP 505.80

1

Zehnder Caladair Pyrostar Smoke and Air Handling Unit

Zehnder Caladair Pyrostar Smoke and Air Handling Unit Caladair Pyrostar is smoke and air handling unit that is suitable for external and internal applications. Pyrostar smoke extraction units met legal requirements for the extraction of smoke and hot gases in the event of a fire in high rise and public assembly buildings with a rating of 2hrs. The range is also designed for the intermediate or continuous extraction of contaminated air from industrial premises, professional kitchens and carparks. High quality bespoke units manufactured in Spain to order (please contact office for delivery date) Key features Smoke and air handling unit Suitable external and internal applications 2hr fire rating @400 degree CE certificate for smoke and heat extraction fans which comply with standard NF EN 12101-3 Extracts smoke and hot gases in the event of a fire Extracts contaminated air from industrial premises Belt pulley transmission with IE3 AC motor Flow rates from 600 to 50000 m3/h Pyrostar R is equipped with an epoxy paint backward wheel Pyrostar A is equipped with a forward wheel constructed of galvanised steel Condensate tray at bottom of unit (ECP option) for removal of condensates Variable drive pulley up to 5.5 kW Protective housing for the transmission on the fan compartment side, easily removable for belt replacement. Fitted with bird protection mesh on outlet Isolation switch installed on unit High quality Construction. Models Pyrostar range is available in 5 sizes and 20 models. The range covers flow rates from 600 to 50000 m3/hr either in impulse turbine version for pressures up to 1500 Pa, or reaction turbine versions for pressure up to 2600 Pa. The Pyrostar R version is fitted with a reaction turbine is especially suitable and recommended for applications in professional kitchens or for the extraction of foul contaminated air (car parks, industry, etc.). Available models: Pyrostar 4 / Pyrostar 6 / Pyrostar 10 / Pyrostar 12 / Pyrostar 15 / Pyrostar 20 / Pyrostar 25 / Pyrostar 30 / Pyrostar 40 / Pyrostar 50 Supply and extract connections are circular in models 4-12, models 15-50 are square connections. Pyrostar A models– impulse turbine and double opening, made from galvanised steel. It is balanced statically and dynamically

GBP 0.00

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)