mcb.dk | Få success online

Aico Relay Module with 5A Relay Mounts under 2100 160RC amp 140RC Alarms Ei128R

Aico Relay Module with 5A Relay Mounts under 2100 160RC 140RC Alarms Ei128RThe Ei128R is a mains powered Relay Module that triggers external devices such as a strobe light or telecare deviceif the alarmsin the propertyactivate.Compatible with the3000Ei2110e Multi-Sensor Fire Alarm160e Seriesalarms and the 140RC SeriesThe Module has additional trunking knock outsto make as easy to install as possibleand is designed to fit underneath the space of easy-fit or RadioLINK base. However a cover is supplied if needed and containsa set of volt-free contacts as standard.The Relay module can beconfigured to give a 230V output or a 24V output using an external 24V supply.Operation of the Ei128ROn receiving a signal from the alarm system the relay contacts will be operated causing a signal to be sent to the device to which it is connected.The Ei128R can be used to switch into a range of devices ranging from indicating lights to magnetic door handles.The module can be switched to give a pulse output or continuous output for different applications.Technical SpecificationThe Relay is designed to operate whilst the alarm system is sounding to signal ancillary devices such as door closers extractors remote sounders etc. When any of the interconnected alarms sound the signal will cause the relay contacts to switch.The Relay is mains powered and operates on receipt of a signal from the interconnect line of a smoke heat or CO alarm. The relay does not operate if mains power is not present.Volt free contacts Normally Open or Normally Closed rated up to 240V AC5 Amps making it suitable for use with a wide range of AC or DC voltages.The Ei128R is designed for siting under one of the smokeheat alarms listed above. However a cover is supplied if installing remotely or with 260 series CO alarms.More than one Relay can be used in a set of interconnected alarms on the condition that no more than 12 units are used in the system 1 x Ei128R counts as one unit.Fitted with a 4 way connector block for ease of wiring.The relay can be set for Continuous or Pulse operation by operation of a manual switch when in Pulse operation mode the relay contacts will automatically switch back to their original state after 5 seconds.Features 3 x 25mm trunking knockouts for surface wiring and centre knockout for recess wiring.Dimensions of unit 135mm diameter x 20mm depth.Weight inclusive of packaging 170g.Manufactured in Ireland.Key FeaturesFor use with the 2100 160RC and 140RC series alarmsVolt free contacts as supplied for multiple useCan be configured to switch a 230V or 24V deviceTrunking knock-outs for easy and neat wiringAdditional connectors for ease of wiringContinuous or pulse operationFits discreetly behind any smoke heat alarm5 Year Guarantee

GBP 43.28

1

Scope EPOCSVIB Vibrating Pillow Pad for EPOCSNSUK

Scope EPOCSVIB Vibrating Pillow Pad for EPOCSNSUKA vibrating pillow pad designed to fit under the users pillows.Requires EPOCSNSUK Nightstand for EPOC pager.

GBP 54.29

1

Carrier ABT-NSM-A Noise Sensing Microphone for One Controller - Type A

Carrier ABT-NSM-A Noise Sensing Microphone for One Controller - Type AABT-NSM is measurement microphone which is designed to operate under extreme temperatures. Up to 6 microphones can be connected to ABT-NSC6 via 2-wire cable.The ABT-NSM is available in two housings. Lightweight for indoor applications.Key FeaturesOperates under extreme temperatures2 wire analogue connection up to 300 meters from ABT-NSC6Dimensions 200 x 110 mm

GBP 99.44

1

Firebeam SHORT-RM Short Range Mask for up to 20 Metres

Firebeam SHORT-RM Short Range Mask for up to 20 MetresThe short range mask is fitted onto a single reflector for distances under 20m.

GBP 8.33

1

Notifier Honeywell ABT-NSMA Noise Sensing Microphone

Notifier Honeywell ABT-NSMA Noise Sensing MicrophoneABT-NSM is a measurement microphone which is designed to operate under extreme temperatures. Up to 6 microphones can be connected to ABT-NSC6 via 2-wire cable. The ABT-NSM is available in two housings. Lightweight for indoor applications A and enclosures for severe climatic conditions B.DetailsOperate under extreme temperaturesIP 66 rated housing2 wire analogue connection up to 300 meters from ABT-NSC6

GBP 203.00

1

Notifier Honeywell ABT-NSMB Noise Sensing Microphone

Notifier Honeywell ABT-NSMB Noise Sensing MicrophoneABT-NSM is a measurement microphone which is designed to operate under extreme temperatures. Up to 6 microphones can be connected to ABT-NSC6 via 2-wire cable. The ABT-NSM is available in two housings. Lightweight for indoor applications A and enclosures for severe climatic conditions B.DetailsOperate under extreme temperaturesIP 66 rated housing2 wire analogue connection up to 300 meters from ABT-NSC6

GBP 372.00

1

Carrier ABT-NSM-B Noise Sensing Microphone for One Controller - Type B

Carrier ABT-NSM-B Noise Sensing Microphone for One Controller - Type BABT-NSM is measurement microphone which is designed to operate under extreme temperatures. Up to 6 microphones can be connected to ABT-NSC6 via 2-wire cable.The ABT-NSM is available in two housings. Lightweight for indoor applications.Key FeaturesOperate under extreme temperatures 2 wire analogue connection up to 300 meters from ABT-NSC6Dimensions 200 x 146 mm

GBP 182.30

1

Aritech VM611P Recess Mounting Box For Floors

Aritech VM611P Recess Mounting Box For FloorsThe VM611P is a recess mounting box to be used when the seismic detector is mounted in concrete floors under construction.

GBP 141.30

1

RGL Electronics BK600L Adjustable L Bracket For Use With ML600 Maglocks

RGL Electronics BK600L Adjustable L Bracket For Use With ML600 MaglocksThe RGL BK600L is an adjustable L Bracket for use with the ML600 range of maglocks. It is suitable for outward opening doors when there isnt enough room under the frame.Key FeaturesFully adjustable L bracket set for slim maglocksSuitable for outward opening doors when there isnt enough room under the frame2 required for double maglocksFor use on outward opening doorsCompatible with all RGL slimline maglocksAnodised aluminium finishFully adjustable

GBP 10.09

1

STI STI-9803 Steel Cage - Anti Vandal

STI STI-9803 Steel Cage - Anti VandalA protective steel cage for a Fire Detector.Key FeaturesAnti-vandalism cage for manual detectors andor switching equipment3 mm thick steel with white epoxy coatingProtective basket for manual call pointsLifetime warranty under normal use

GBP 51.54

1

Aritech VM602P Recess Mounting Box For Walls

Aritech VM602P Recess Mounting Box For WallsThe VM602P is a recess mounting box to be used when the seismic detector is mounted in concrete walls under construction. For recess mounting in floors you should use the floor mounting box VM611P with extra strong lid.

GBP 104.21

1

International Gas Detectors TOC-750S-FIL End of Line Filter Assembly for 6mm x 4mmm Tube

International Gas Detectors TOC-750S-FIL End of Line Filter Assembly for 6mm x 4mmm Tube Sampler are designed for ambient sampling only. You should only use conduitcable entries provided drilling the enclosure will avoid any warranty.It may be necessary to vent spill gases to a safe areaInstallation RequirementsInterconnecting Highway Cabling for 2-Wire Addressable systems For safe area detectors use 2 core cable 1.0 to 2.5mmSQ cable depending on distance.Ensure Cable Screens are correctly terminated and cables are stripped to the enclosed guide.There are two methods to deploy the EOL assembly. Under ideal circumstances the assembly should be fitted at the very end of the sample tube as this provides the best protection but we can appreciate under certain circumstances this option may not be possible.

GBP 136.08

1

Vesda Xtralis REDDSK Discrete Sampling Point cw Reducing T Piece amp 1.5m x 10mm Capillary Pipe

Vesda Xtralis REDDSK Discrete Sampling Point cw Reducing T Piece 1.5m x 10mm Capillary PipeThe REDDSK is a Discrete Sampling Point Kit.All Aspirating Pipe and Fittings supplied by Morley-IAS are produced under a strict quality control system approved to EN ISO 9001.Key FeaturesComes with a reducing T Piece 1.5 x 10mm Capillary Pipe

GBP 17.23

1

C-Tec FLAT4005 100m x 2.5mm2 Insulated Copper Tape

C-Tec FLAT4005 100m x 2.5mm2 Insulated Copper TapeA 100m reel of 2.5mm2 insulated flat copper foil tape ideal for use as a floor loop under light duty carpets in audio-frequency induction loop systems. Protective tape is also required to hold the cable down and reduce the likelihood of damage.Key FeaturesConnect to an AFILS amplifier using solder or a 1A choc block.

GBP 234.62

1

Carrier ABT-NSC6 Noise Sensing Controller

Carrier ABT-NSC6 Noise Sensing ControllerABT-NSC6 is a TCPIP controller specially designed for the use with MULTIVES and miniVES systems. The main roll of the device is collecting audio data from 6 measurement microphones and automatic volume control of background music and announcements in assigned speaker zones.Key FeaturesOperates under extreme temperaturesIP66 housingUp to 24 controllers on the networkUp to 6 noise sensing microphones per controller

GBP 1034.72

1

Spring Balance Scale - 20kg

Spring Balance Scale - 20kgSpring balance scales are ideal for usage on fire extinguishers they help to determine the weight of extinguishers and we supply a range of 1kg 2kg 20kg spring balanced scales. The weight of an extinguisher is usually routine check in a commission service and is usually recorded under annual service intervals.Key FeaturesLightweightEasy to useMust have tool for service checksWeight Capacity 20kg

GBP 37.73

1

Spring Balance Scale - 2kg

Spring Balance Scale - 2kgSpring balance scales are ideal for usage on fire extinguishers they help to determine the weight of extinguishers and we supply a range of 1kg 2kg 20kg spring balanced scales. The weight of an extinguisher is usually routine check in a commission service and is usually recorded under annual service intervals.Key FeaturesLightweightEasy to useMust have tool for service checksWeight Capacity 2kg

GBP 34.31

1

C-Tec VL1 PDA 1.2m2 12V Vehicle Hearing Loop

C-Tec VL1 PDA 1.2m2 12V Vehicle Hearing LoopThe VL1 12V Vehicle Hearing Loop is ideal for cars taxis buses and other privatecommercial vehicles.Key FeaturesLoop can be positioned in the vehicles roof lining under a seat across the back of a seat or in a door panel to suit the applicationMetal compensation control helps combat the frequency response problems caused by metal absorbing the magnetic field

GBP 156.78

1

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual Battery

Elmdene GEN3-34-R 13.8v 3A SMPSU Dual BatteryThe GEN series of switch mode power supplies has been specifically designed to provide a comprehensive and flexible range for engineers designing intruder alarm systems to Grade 2 and Grade 3 under EN50131-62017 and PD66622017Key Features13.8V dc outputCost effective switch mode technologyEnergy efficientFull current to load plus additional current to charge standby batteryInternal LED PSU statusMains transient protection

GBP 199.39

1

C-Tec 100m x 1.0 mm2 Insulated Copper Tape FLAT2005

C-Tec 100m x 1.0 mm2 Insulated Copper Tape FLAT2005A 100m reel of 1.0mm2 insulated flat copper foil tape ideal for use as a floor loop under light duty carpets in audio-frequency induction loop systems. Protective tape is also required to hold the cable down and reduce the likelihood of damage.Key FeaturesConnect to an AFILS amplifier using solder or a 1A choc block

GBP 192.91

1

Hochiki FIREscape Phase Monitor Relay Unit EL-PM

Hochiki FIREscape Phase Monitor Relay Unit EL-PMEL-PM is an under-voltage monitoring device that constantly assesses the condition of a mains lighting circuit. When the lighting circuit is deemed faulty the unit will provide a signal that can be relayed to the control equipment to initiate emergency luminaire activation.Key FeaturesTriggers at 75 of the nominal lighting circuit supplyDIN Rail mountedPower and output indications

GBP 72.04

1

Aico Surface Mount Kit for 2100 160RC amp 140RC Series Alarms Ei127

Aico Surface Mount Kit for 2100 160RC 140RC Series Alarms Ei127The Ei127 is a Surface Mount Kit for use with 2100 160RC and 140RC Series Smoke and Heat Alarms. It allows additional space for wiring connections. It has 3 x 1625mm trunking knock outs for surface wiring.Key FeaturesFits under any 2100 160RC 140RC series alarms3 way connector block used for wiring mains and interconnect

GBP 4.15

1

C-Tec 100m x 1.5 mm2 Insulated Copper Tape FLAT3005

C-Tec 100m x 1.5 mm2 Insulated Copper Tape FLAT3005A 100m reel of 1.5mm2 insulated flat copper foil tape ideal for use as a floor loop under light duty carpets in audio-frequency induction loop systems. Protective tape is also required to hold the cable down and reduce the likelihood of damage.Key FeaturesConnect to an AFILS amplifier using solder or a 1A choc block

GBP 315.55

1

Carrier TX-2213-03-1 Wireless PIR 12m 868AM GEN2

Carrier TX-2213-03-1 Wireless PIR 12m 868AM GEN2A wireless PIR 12m. Generation 2.Key FeaturesProven mirror optics inside to get a dense coverage patternSelectable coverage pattern using mirror masksFull under crawl detection5D signal processing for false alarm immunityAuto focus with constant range sensitivityNo adjustment required for different mounting heightsTolerates wall angle deviationEnd-user friendly product design for exchanging batteries5-years battery life with 1 batteryHolding several security approvals

GBP 73.45

1

Vimpex HYDW-05-KIT 5M Hydrowire Starter Kit - Contains HYDW-05 HS-HWCI HS-HWCI-EOL

Vimpex HYDW-05-KIT 5M Hydrowire Starter Kit - Contains HYDW-05 HS-HWCIHS-HWCI-EOLVimpex Hydrowire can be plugged together to form detectionzones of up to 50m in length. This very responsive sensing cable is designed tobe fitted under false floors in ceiling voids and other enclosed spaces. Key Features5m LengthUp to 50m per zoneFixing clips availableCan be fitted around the perimeter of the buildingKit Contains HYDW-05 HS-HWCIHS-HWCI-EOL

GBP 155.11

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)