mcb.dk | Få success online

C-Tec 50m Printed Hearing Loop Foil Loop Tape TAPEP

C-Tec 50m Printed Hearing Loop Foil Loop Tape TAPEPA 50m reel of high quality printed Induction Loop foil tape.Key FeaturesUltra-sticky adhesiveIdeal for securingflat copper foilcable to floors etcIncludes warning symbols to avoid inadvertent damage or removal50mm wide

GBP 44.87

1

Notifier M700X Loop Isolator Module

Notifier M700X Loop Isolator ModuleThe M700X is a loop isolator module with plug-in screw connections and LED.

GBP 71.39

1

System Sensor M200XE Loop Isolation Module

System Sensor M200XE Loop Isolation ModuleThere is a large number of System Sensor intelligent fire alarm systems the address loop with a recipient device up to 198 is protected by a single one loop interruption but in the case of loop short circuit the entire loop it may become inoperable. With the M200XE modules shorting is not desired can be reduced.Only a small part of the system falls out if the loop is broken down into isolators because in the case of a possible loop only the two isolators will not be available to the control panel. If the address loop voltage drops below 7V the isolator module - with FET on the branch breaks it off the loop in the non-short-term part of the address loop the assets remain operational. If the breakdown the loop voltage rises on one side of the module then the separated short-circuit loop section 3 mA max. 15 mA control current flows through the module.In isolation the address loop wires between min. 2.2 kOhm resistance. The isolated state is maintained until the voltage of the disconnected section is 7V the short-circuit or the abnormally high current consumption ceases to exist. After the termination of the termination the isolator disengages the loop automatically.The two-colour LED on the module flashes green in the normal state of the loop every 3 seconds. If the module on any side it detects a short-circuit it illuminates with continuous yellow light during the shutter. The M200XE module in the M200E-SMB mounting box is wall-mounted with the M200E-DIN clip directly on the DIN rail M200E-PMB clip can be mounted in the fire panels box.

GBP 55.08

1

C-Tec PL1PSU1 PDA Portable Hearing Loop PSU UK

C-Tec PL1PSU1 PDA Portable Hearing Loop PSU UKThe PL1PSU1 is a PDA Portable Hearing Loop PSU.

GBP 72.56

1

Cooper Menvier MAS750 Loop Wired Sounder Base

Cooper Menvier MAS750 Loop Wired Sounder BaseAn addressable sounder base.Key FeaturesLoop wiredAddressableLegacy product

GBP 72.90

1

Hyfire Intelligent Loop Powered Sounder Base HFI-ABS-05

Intelligent Loop Powered Sounder BaseThe HFI-ABS-05 is a fully intelligent and aesthetically pleasing low profile Base Sounder. By utilising the Hyfire fully digital communication protocol reliable and fast operation is achieved even when employing the impressive 240 device loop capacity.Once installed on to a compatible loop the device is fully addressable and benefits from an extensive range of intelligent functionality including sounder synchronisation. The units integral detector base has easy access for loop cabling and allows for the connection of both the sounder and associated detector via a single set of cable terminations.Key FeaturesEmploys fully digital Hyfire protocolBuilt in loop isolatorsFully IntelligentSelection of 32 tonesSynchronised sounderAdjustable volume outputAuto-addressableProgrammable via Device Programming ToolCompatible with all Altair detectors5-year product warrantyIncludes device identification tabEasy central cable entry

GBP 63.49

1

Vimpex Loop Sounder with Short Circuit Isolator ELS2A6AO

Vimpex Loop Sounder with Short Circuit Isolator ELS2A6A0Installing a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.Key FeaturesApproved to EN 54

GBP 44.11

1

Vimpex ELS2A4AO Loop Sounder with Shallow Base in White

Vimpex ELS2A4AO Loop Sounder with Shallow Base in WhiteInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 44.11

1

Hyfire HFI-ABS-06 Intelligent Plus Loop Powered Sounder Base Altair

Hyfire HFI-ABS-06 Intelligent Plus Loop Powered Sounder Base AltairThe HFI-ABS-06 is a fully intelligent and aesthetically pleasing low profile Base Sounder. By utilising the Hyfire fully digital communication protocol reliable and fast operation is achieved even when employing the impressive 240 device loop capacity.Once installed on to a compatible loop the device is fully addressable and benefits from an extensive range of intelligent functionality including sounder synchronisation. The units integral detector base has easy access for loop cabling and allows for the connection of both the sounder and associated detector via a single set of cable terminations.Key FeaturesBuilt in loop isolatorsFully IntelligentSelection of 32 tonesSynchronised sounderAdjustable volume outputAuto-addressableAltair

GBP 53.35

1

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in Red

Vimpex ELS3A6AO Loop Sounder with Deep Base IP66 in RedInstalling a Vimpex Loop Sounder System with short-circuit isolation provides complete sounder circuit integrity. By wiring the sounder circuit in a loop instead of a traditional radial all sounders will remain operational in the event of a short-circuit or open circuit fault.Component parts are approved by LPCB to relevant parts of EN 54 and the system is fully compliant with BS 5839-1 using a single sounder loop. Use of the Vimpex Loop Sounder System will greatly increase the reliability of the sounder circuits and in many cases result in a saving in the amount of cable used.Each loop can accommodate up to 45 sounders. Suitable for use on both conventional and addressable fire alarm systems the system provides much greater protection against faults than the dual radial circuit arrangements commonly used.The Vimpex Loop Sounder System significantly enhances the reliability of any sounder system. With conventional radial circuits a single open or short circuit fault on a sounder circuit could result in the loss of at least half of the sounders in an area of a building.The Vimpex Loop Sounder System has been fully tested and approved by LPCB to relevant EN 54 standards - certificates are available on request. This system is detailed in BS 5839-12002A22008 clause 12.2.2 j and Fig 1b as an alternative to the use of dual radial circuits. A detailed application guide is available from Vimpex as is a system loop calculator.Each sounder is supplied with a bi-directional short-circuit isolator fitted within its base. In the event of a short circuit the isolators will activate and disconnect the faulty section of cable while reporting in monitoring mode the fault to the control panel. When the sounders are activated the loop is driven from both ends ensuring that all sounders will remain operational even in the event of a single short-circuit or open-circuit fault. Sounders and their isolator bases are installed just like any other conventional sounders on the twin core circuit.

GBP 45.36

1

C-Tec RXTI2 Hearing Loop Listener

C-Tec RXTI2 Hearing Loop ListenerAllows installers and non-hearing aid users to quickly assess the quality and audibility of an induction loop system ideal for daily system checking. The unit also allows non-hearing aid users to listen to the amplified sound generated by hearing loops in theatres cinemas churches etc. bringing performances sermons and general conversation closer to their earsKey FeaturesOn board filters helps reduce mains hum and background noiseIdeal for surveillance museum talk-through and stage manager talk-back systemsRotary onoff and volume control cw soft start functionality3.5mm headphone socket Impedance of headphones not supplied should be no greater than 32 ohmRequires 2 x AAA batteries

GBP 72.67

1

Zeta ZIOU230 Interface Module Loop Powered 5.0A Rating

Zeta ZIOU230 Interface Module Loop Powered 5.0A RatingThe Mains IO Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the Fire Alarm Control panel using normally open dry contact connections.The connection to the input is monitored for fault open or short circuit and Alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing systems etc.Module is provided with a loop short-circuit isolator and with a voltage free single pole change over mains rated output.The output relay is always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an on-board red LED. An 8 way D.I.L switch is provided to configure the modules address.This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.The Simplicity CO 8 range is designed to detect monitor CO concentrations in places such as warehouses car parks tunnels and enclosed buildings where forklifts cars and delivery trucks can produce deadly amounts of carbon monoxide in high traffic areas Carbon Monoxide can accumulate in these areas and can be a serious safety and health concern.Key FeaturesFast Activation ResponseLoop PoweredFive Status LEDs providedLow Power ConsumptionModule features an integral short-circuit loop isolatorSingle mains rated relay contact

GBP 78.77

1

Cooper MAB870 Intelligent Addressable Loop Connected LED Indicator CAB382

Cooper MAB870 Intelligent Addressable Loop Connected LED Indicator CAB382The Menvier intelligent addressable loop connected LED beacon is available to complement audible alarms for use in areas either where people may be present who have impaired hearing or areas with high ambient noise levels. The Menvier MAB870 is designed for both wall and ceiling mounting has a built in short circuit isolator and is soft addressed for ease of installation.Key FeaturesHigh efficiency designLED technologyLow profile designBenefitsLow currentHigh efficiency LED visual unit suitable for DDA compliance

GBP 66.02

1

C-Tec BF335CTB 24V Loop Voice Sounder VID Base White

C-Tec BF335CTB 24V Loop Voice Sounder VID Base WhiteThe BF335CTB is a white addressable voice sounderVID base with isolator designed to be compatible with the Apollo Discovery range.

GBP 55.54

1

Apollo Loop-Powered Amber Visual Indicator - 55000-879APO

Apollo Loop-Powered Amber Visual Indicator - 55000-879APOThe Loop-Powered Visual Indicator is a local-area visual indicator designed for indoor use. The Visual Indicator has been developed as a supplement to sounders for use in situations where there is a risk that sounders will not be heard.The Base responds to its own individual address set with a DIL switch. It also responds to a group address set by means of a 4-segment DIL switch and to a synchronisation address which is embedded in the unit.Key FeaturesHigh intensity LEDsMore reliable than xenon visual indicatorsAutomatic LED checkLockableWide angle of visibilityEnables DDA complianceSynchronised flashCan be used with Discovery or XP95

GBP 47.11

1

Apollo Loop-Powered Clear Visual Indicator 55000-878APO

Apollo Loop-Powered Clear Visual Indicator 55000-878APOThe Loop-Powered Visual Indicator is a local-area visual indicator designed for indoor use. The Visual Indicator has been developed as a supplement to sounders for use in situations where there is a risk that sounders will not be heard.The Base responds to its own individual address set with a DIL switch. It also responds to a group address set by means of a 4-segment DIL switch and to a synchronisation address which is embedded in the unit.Key FeaturesHigh intensity LEDsMore reliable than xenon visual indicatorsAutomatic LED checkLockableWide angle of visibilityEnables DDA complianceSynchronised flashCan be used with Discovery or XP95

GBP 47.11

1

Hochiki Loop Powered Wall Mounting Sounder - Red CHQ-WS2

Hochiki CHQ-WS2 Loop Powered Wall Mounting Sounder Red.Model CHQ-WS2 is an addressable loop powered Wall Sounder innovatively designed to provide a range of tones and volumes with a maximum output of up to 102dBA 2dBA with low current consumption. The unit is designed to fit to the Standard Base YBO-R3RED or the Isolator Base YBO-RSCIRED. The sounder is IP rated to IP21 for internal use but it can be made weatherproof by utilising the WS2-WPK Weatherproof Kit which consists of a specialised back box and gasket set.Also incorporates an auto shutdown mode which allows the user to set a fixed time within which the sounder will operate before automatically silencing itself ideal for minimising noise pollution.Key FeaturesLoop PoweredSingle Loop Address - addressed via the TCH-B100 Hand Held ProgrammerVariable Sound Output 90 102 dBA -2 dBA output at 1 metreFits Hochiki Standard or Isolator BaseWeatherproof Kit available51 User-Selectable Tones all tones EN54-3 compatibleAlso available in whiteApproved by LPCB VdS

GBP 45.98

1

Hochiki Loop Powered Wall Mounting Sounder - White CHQ-WS2WHT

Hochiki CHQ-WS2WHT Loop Powered Wall Mounting Sounder WhiteModel CHQ-WS2WHT is an addressable loop powered Wall Sounder innovatively designed to provide a range of tones and volumes with a maximum output of up to 102dBA 2dBA with low current consumption. The unit is designed to fit to the Standard Base YBO-R3WHT or the Isolator Base YBO-RSCIWHTSNDR.The sounder is IP rated to IP21 for internal use but it can be made weatherproof by utilising the WS2-WPKWHT Weatherproof Kit which consists of a specialised back box and gasket set.Also incorporates an auto shutdown mode which allows the user to set a fixed time within which the sounder will operate before automatically silencing itself ideal for minimising noise pollution.Key FeaturesLoop PoweredSingle Loop Address - addressed via the TCH-B100 Hand Held ProgrammerVariable Sound Output 90 102 dBA -2 dBA output at 1 metreFits Hochiki Standard or Isolator BaseWeatherproof Kit available51 User-Selectable Tones all tones EN54-3 compatibleAlso available in redApproved by LPCB VdS

GBP 45.98

1

Aritech Addressable 2000 Series Loop Powered Sounder Multi Tone Deep Base - AS2364W

Aritech Addressable 2000 Series Loop Powered Sounder Multi Tone Deep Base - AS2364WThe AS2364W is a WHITE bodied deep base addressable room sounder for fire alarm systems running 2000 series addressable fire protocol. Multiple tone selection and full CPD approval ensure conformance to local regulations.The sounders operate over a 2-wire 2000 series loop and are loop powered i.e. no external power supply is required. They are compatible with automatic phased-start synchronisation controlled from the fire panel. The AS2364W has a IP65 enclosure.Key FeaturesLoop poweredHigh sound output with low current consumptionMultiple tone selectionSuitable for multiple stage evacuation with up to 3 pre-set tonesAutomatic synchronisationIP65 ratedCPD certified

GBP 77.74

1

Aritech Addressable 2000 Series Loop Powered Sounder Multi Tone Deep Base - AS2364

Aritech Addressable 2000 Series Loop Powered Sounder Multi Tone Deep Base - AS2364The AS2364 is a RED bodied deep base addressable room sounder for fire alarm systems running 2000 series addressable fire protocol. Multiple tone selection and full CPD approval ensure conformance to local regulations.The sounders operate over a 2-wire 2000 series loop and are loop powered i.e. no external power supply is required. They are compatible with automatic phased-start synchronisation controlled from the fire panel. The AS2364 has an IP65 enclosure.Key FeaturesLoop poweredHigh sound output with low current consumptionMultiple tone selectionSuitable for multiple stage evacuation with up to 3 pre-set tonesAutomatic synchronisationIP65 ratedCPD certified

GBP 77.74

1

Aritech Addressable 2000 Series Loop Powered Multi-Tone Sounder with Shallow Base - AS2363W

Aritech Addressable 2000 Series Loop Powered Multi-Tone Sounder with Shallow Base - AS2363WThe AS2363W is a WHITE bodied addressable room sounder for fire alarm systems running 2000 series addressable fire protocol. Multiple tone selection and full CPD approval ensure conformance to local regulations.The sounders operate over a 2-wire 2000 series loop and are loop powered i.e. no external power supply is required. They are compatible with automatic phased-start synchronisation controlled from the fire panelKey FeaturesLoop poweredHigh sound output with low current consumptionMultiple tone selectionSuitable for multiple stage evacuation with up to 3 pre-set tonesAutomatic synchronisationCPD certifiedVdS Approved

GBP 69.41

1

Aritech Addressable 2000 Series Loop Powered Multi-Tone Sounder with Shallow Base - AS2363

Aritech Addressable 2000 Series Loop Powered Multi-Tone Sounder with Shallow Base - AS2363The AS2363 is a RED bodied shallow base addressable room sounder for fire alarm systems running 2000 series addressable fire protocol. Multiple tone selection and full CPD approval ensure conformance to local regulations.The sounders operate over a 2-wire 2000 series loop and are loop powered i.e. no external power supply is required. They are compatible with automatic phased-start synchronisation controlled from the fire panel.Key FeaturesLoop poweredHigh sound output with low current consumptionMultiple tone selectionSuitable for multiple stage evacuation with up to 3 pre-set tonesAutomatic synchronisationCPD certifiedVdS Approved

GBP 70.80

1

Aritech AS964I 950 Series Intelligent Loop Powered Open-Area Sounder with Isolator Red

Aritech AS964I 950 Series Intelligent Loop Powered Open-Area Sounder with Isolator RedThe AS964I is a 950 series intelligent loop powered open-area sounder in RED with a built in isolator. It is designed for use in indoor and outdoor open area applications. It supports 3 tones with two volume settings.A locking mechanism is available to prevent unauthorized removal of the AS964I from its base.Isolation and MaintenanceThe AS964I sounder is supplied with an isolating base. A yellow LED on the base is illuminated if a loop short circuit is detected. All fault and abnormal conditions such as sounder failures are reported back to the panel for easy fault-finding.Sounder Tone SupportThat AS964I supports the following tonesStandardSlow Whoop NEN2575DIN 33404pt3Two volume settings are available in each tone variantKey FeaturesSelf-test fault monitoringMultiple tonesAlarm synchronisationLoop poweredIncluding loop isolatorApollo equivalent 55000-001

GBP 84.06

1

Nittan Evolution EV-ZMU2 Zone Monitor Module Loop Powered

Nittan Evolution EV-ZMU2 Zone Monitor Module Loop PoweredEV-ZMU2 is a Loop Powered Dual Input Zone Monitor module with integral ve line Short circuit isolator compatible with Evolution analogue addressable system devices. The Module includes setting options for Class A or Class B Zone inputs. LEDs are provided to Indicate Input active Fault and Isolator Open.The module is designed to fit the range of standard UK 2-Gang electrical enclosures including Surface Flush mount options. Device address may be set using EV-AD2-EXT Hand held programmer. The Short Circuit Isolator will protect the system whilst allowing the device to continue communication from the opposite side. The isolator will self-reset when the fault clears.The Zone Monitor can support the following devices on each Zone InputEVC-P EVC-H-A2SCS 20 unitsEVC-DP Loop 24V min 20 unitsEVC-IR Flame Detector 5 unitsEVC-PY-IS Zener Barrier 15 unitsThe following resistors are required for Fault and Alarm monitoringEOL 4k7 OhmAlarm 375 to 680 Ohm EVC has Alarm integral to head

GBP 84.24

1

Morley MI-DSS-PC-I05 Loop-Powered Open Category Detector Base Sounder Strobe - Isolated Version

Morley MI-DSS-PC-I05 White Base Clear Lens Loop-Powered Open Category Detector Base Sounder Strobe - Isolated VersionMI-DSS-PC-I05 is a Loop-Powered Open Category Detector Base Sounder Strobe Isolated Version.The MI-DSS-PC-I05 requires a B501AP base for fast and simple installation for Morley detectors and a choice of sound output levels and tones selectable from the device or panel.The Morley-IAS IAV Audio Visual sounders are designed to inform building users of an emergency. The IAV range of intelligent addressable loop powered audio-visual sounders include a comprehensive selection of elements designed to meet the majority of fire alarm installation requirements. The sounders use the Morley-IAS Digital Protocol to minimize power consumption and allow longer loop lengths.Key FeaturesEN54-23Isolated versionWhite Base Clear Lens

GBP 70.20

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)