mcb.dk | Få success online

Aritech GS331 Glassbreak Detector Tester

Aritech GS331 Glassbreak Detector TesterThe tester GS331 is used to verify the operation of the glued-on-glass glass break detectors GS300310. You test the detector by pressing the tester against the window. A noise will be heard simulating a glass breakage. It is recommended to test the glass break detectors before and after the installation.Please note that this is not a range tester.Key FeaturesAutomatic switching offBattery display via LED

GBP 270.73

1

Aritech GS960-TR GS960 Tester And Calibration Tool For Optimal Functioning Of The Sensor In The Acoustic Space

Aritech GS960-TR GS960 Tester And Calibration Tool For Optimal Functioning Of The Sensor In The Acoustic SpaceThe GS960-TR tester is a specially developed tool for calibrating and adjusting the GS960 Series for optimal function in the acoustic space the DRC Digital Room Compensation procedure. Using this tool to test the detector settings you do not need to open it again as the tester will communicate with the detector acoustically.

GBP 209.59

1

C-Tec FiTT EVC Line Tester

C-Tec FiTT EVC Line TesterThe FiTT line tester is an easy to use test set which allows you to test the wiring for a SigTEL Type A fire telephone outstation andor a SigTEL Type B disabled refuge outstation prior to its connection to an appropriate SigTEL exchange unit.The FiTT is supplied with a non-rechargeable 9 volt PP3 alkaline battery allowing approximately 28 hours use and all the test cables and connectors you need. Always replace the battery with a non-rechargeable 9 volt PP3 alkaline battery. Do not use a rechargeable battery.

GBP 329.02

1

ACT 12v Chrome Intelligent Battery Tester

ACT 12v Chrome Intelligent Battery TesterFast IdentificationThe ACT CHROME 12V SLA Battery Tester uses advanced pulsed load technology to deliver accurate DC Voltage and Ah capacity results based on the batterys temperature and state of charge. A quick look up table on the side of the unit identifies when batteries should be recharged or replaced due to age or operating conditions 65 of rated capacity. A temperature sensitive strip allows the ambient temperature to also be recorded.The ACT CHROME 12V SLA Battery Tester offers a simple and accurate solution for testing 12V SLA batteries commonly used in fire security and many other electrical systems.SuppliedACT CHROME 12V SLA Intelligent Battery Tester ACT 3532 Terminal Connectors ACT 410N Soft Carry Case Sample ACT BTL Labels Operating Instructions and Certificate of CalibrationQuick Tip Temperature effects capacityMany battery manufacturers rate their batteries at20CBelow 20C the battery can have a significantly lower available capacityOver 20C the battery can have a significantly higher available capacityThis can easily be as much as 50 of the rated capacityBear in mind the differences in temperature when testing for example in an enclosure or next to a hot transformer high than rated reading or located externally cold environment lower than rated readingQuick Tip State of charge effects capacityMost battery manufacturers rate their batteries at restCharging voltages and currents have a direct impact on available capacityBear in mind when testing batteries recently removed from chargeMany new batteries are not fully charged when producedQuick Tip Connection effects resultsAlways connect to clean battery terminalsA tight grip around the battery tab terminals is essential for accurate readingsDo not connect to high resistance bolts as this will produce low Ah resultsWhere bolt connections are present use theACT 3532 Battery Terminal Connectorssupplied with your ACT CHROMEKey FeaturesCompact design and simple operationSimulates a 20 hour C20 discharge test in secondsDesigned for 12V standby SLA batteries between 1.2Ah and 200AhAutomatically displays the DC Voltage and available Ampere hour Ah capacity based on the batterys temperature and state of chargeQuickly verify voltage and capacity of new straight-out-of-the-box batteriesIdentify low or abnormal capacity of used batteriesReverse polarity protectionPowered by the battery under testFree from complicated settings and functions

GBP 286.80

1

ACT 612V Intelligent Battery Tester ACT612

ACT 612V Intelligent Battery Tester ACT612Simulates a full 20 hour battery discharge test in seconds. The ACT612 is a dual voltage intelligent battery tester designed for 6V and 12V lead acid batteries from 1.2Ah to 100Ah making it capable of testing 12V batteries up to 150Ah. Its the only product of its kind to have an Ampere-hour Ah calibration control enabling Ah readings to be adjusted to suit various battery technologies including standby SLA AGM cyclic GEL and car FLOODED WET batteries.The ACT612 contains advanced pulsed load analysis technology which removes surface charge to accurately measure the available Ah capacity based on the batterys temperature and state of charge. This enables you to check the voltage and test the capacity of new batteries straight from the box as well as used batteries which may show abnormal Ah capacity caused by excess temperature or from being under or overcharged.A table on the front of the meter indicates when batteries should be recharged or replaced due to age or operating conditions 65 of rated capacity. The ACT612 is designed for those who need to test different types of lead acid batteries quickly and easily.Key FeaturesTests 6V12V SLA GEL and Flooded lead acid batteriesSimulates a full 20 hour battery discharge test in secondsCapable of testing 12V batteries up to 150AhDisplays DC voltage and Ampere-hour Ah capacity available in the batteryAdvanced pulse load analysis accurately measures Ah capacity available in secondsAccurate Ah capacity based on batterys temperature and state of chargeUnique Ah Calibration Control enables standby SLA cyclic GEL and car FLOODED batteries to be testedUltra low heat generation allows continuous battery testingReverse polarity protection with LED warning indicationOver Voltage Protection to max 30VDC with LED warning indicationReplaceable plug-in test leadsHigh Impact ABS case with holsterCalibration Certification includedIdeal for those who need to test a broad range of lead acid batteries types in various applications such asfire and security systems UPS golf mobility and leisure etc.Technical InformationOperating Voltage 6V and 12V DCReverse Polarity Protection Red LED IndicationMax Input Voltage 15VDCOver Voltage Protection Max 30VDC 10 sec. with Red LED IndicationBattery Types SLA AGM GEL Flooded WETBattery Sizes 6V 1.2Ah 10Ah and 12V 1.2Ah to 100AhAh Capacity Test Simulated 20 hour C20 load test to 10.50VDCAh Calibration Calibrated at 0 zero position to brand new fully charged premium brand SLA batteries rated at C20 hour at 20C 68FAh Result Based on the battery under test temperature and state of chargeAdjustment Provides Ah adjustment to brand new fully charged standby SLA cyclic GEL and car FLOODED lead acid batteriesBattery Table Recharge or replace battery when Ah capacity available falls below 65 of the batterys stated capacityDisplay Type Blue Back-lit LCDFlat Battery Warning 6V 5.30VDC 12V 10.50VDCRepeat Test Operation Can perform repeat tests continuouslyDCV Accuracy 2 of displayed readingAh Accuracy 5 Fully charged premium brand C20 hour rated SLA batteries at 20 - 25C 68F - 77FApplied Pulse Load 6A 1.2Ah - 7Ah 18A 8Ah - 100AhAh Cal Adjustment Approx 25 dgtsCase Construction High impact ABS with holsterSize 84H x 170W x 41D mm including holsterWarranty 12 months RTBIN THE BOX ACT612 Intelligent Battery Tester ACT612TL Test Leads ACT430N Soft Carry Case Sample ACTBTL Labels Operating Instructions and Certificate of Calibration

GBP 258.72

1

Testifire XTR2 TESTIFIRE-GEN-1PK-001 Smoke Generator Pack of 1

Testifire XTR2 TESTIFIRE-GEN-1PK-001 Smoke Generator Pack of 1A replacement smoke generator for the Testifire XTR2 smoke and heat tester.

GBP 297.08

1

SAS RED2501 Infrared Transmitter Tester

SAS RED2501 Infrared Transmitter TesterThis desk mounted test unit is used to check that the RED2081 and RED2092 transmitters are sending the correct signals and that battery levels are healthy. It is not needed to test the RED20856 and 7 transmitters as these include built-in test features.The transmitter is inserted into the test station so as not to activate any nearby infrared receivers. Ideally positioned at the reception desk so staff can test their transmitters at regular intervals. It is supplied with a plug top power supply unit.

GBP 202.50

1

PROBE TEST Heat Probe Testing Tool 120W

PROBE TEST Heat Probe Testing ToolProbe-Test is an alternative to a gas torch or heat gun for testing Probe type Point Heat Detectors. Its advantages are particularly relevant when working in conditions where naked flame or exposed heating elements is unsafe or inconvenient. For example in roof spaces under floor spaces close to special wall or ceiling finishes. The heads reach a working maximum temperature of 520 Degrees Celsius.Key FeaturesHigh Power 120WNo Naked FlamesTests in SecondsTemperature ControlledFull Instructions IncludedThe heads reach a working maximum temperature of 520 Degrees Celsius.Available in 120v although lead times may be longer. Please Contact Us for more information.InstructionsThese instructions should be carefully followed each time the Probe-Test is used. Instructions using standard Point Type Heat Probes e.g. Fenwal Tyco Olsen T54B etc.Select appropriate heads for the diameter of detector probe shaft e.g. .Slide the heads onto the shaft until they bottom out. It is important that the heads do not slide easily off the shaft.Place Probe-Tester in a safe location. Switch ON at mains the indicator will glow Amber. Allow approximately 4 minutes to attain full working temperature.Position the two heated heads on the Probe-Test over the Heat Probe to be tested approximately 20mm from the end of the probe. Grip the handles firmly ensuring the heads remains at 90 degrees to the probe. Hold until the Heat Probe Detector actives.Remove Probe-Test from the Detector unplug from the mains and allow the Probe-Tester to cool.

GBP 210.00

1

C-TEC XFP501ECA XFP 1 Loop 16 Zone Panel C-TEC CAST. Max. 2 x 3.2Ah Batteries

C-TEC XFP501ECA XFP 1 Loop 16 Zone Panel C-TEC CAST. Max. 2 x 3.2Ah BatteriesC-TECs tried and trusted XFP oneloop 16zoneaddressable fire alarm panel - now available with C-TECs own digital fire alarm system protocol CAST and fully certified to EN54 parts 2 4 and 13.With a powerful 40V 500mA loop driver allowing the connection of up to 255 CAST devices the installation of a cost-effective feature-packed addressable fire alarm system has never been easier.Always thought of the XFP as an entry-level fire panel Think again. Thanks to CASTs multiple type codes high speed data transmission and two speedy soft addressing options automatic via the panel or manually via a handheld programmerdevice tester it is undoubtedly one of the most powerful single loop fire panels around. This and its ability to sit on a network of up to 8 XFP master panels makes it ideal for use in small to medium sized stand-alone applications and larger more sophisticated installations alike.Protocol FeaturesCAST is the worlds most-advanced distributed intelligence fire alarm system protocol. Conceived designed and realised by C-TEC as part of a five-year multi-million pound project it involved the creation of a powerful proprietary communication protocol C-TEC Addressable System Technology CAST and multiple control panels field devices. Now available to purchase.Key Features 255 devices per loop. Autonomous decision-making for faster response times. Multiple type codes. 40V loop drive voltage. Two soft addressing options automatic via the panel or manual via a powerful handheld programmer. Powerful multi-level addressing facilitates easy device addition and swapped device identification. Multiple functionality at a single address integrated devices - due 2021. Volumes tones detector modes can be changed at compatible panels. High-speed data transmission and robust data transfer. Provides geographical location of short and open circuit faults a short circuit isolator is included as standard in every CAST field device. Replace device function. Programmable multi-function status LED. Future seamless integration with other CAST life safety systems reducing energy servicing installation and repair costs. ENVISION Enabled - fully compliant with our new ENVISION Cloud-based Fire IoT Remote Access System Test and Site Management software package. Designed and manufactured in the UK.Panel Features Certifiedto EN54-24 by the Loss Prevention Certification Board LPCB and EN54-13 by Kiwa Telefication. Two independently programmable conventional sounder circuits. Two programmable inputs. A fault output relay and three programmable relay outputs with voltage free changeover contacts. A selection of zone dependencycoincidence functions. A daynight building occupiedunoccupied function. An investigation delay period function. Phased evacuation facility. An alarm counter that records how many times the panel has been in alarm state. Powerful short circuit protected loop drivers. An integral EN54-4A2 switch mode. Adjustable contamination levels. Earth fault monitoring. Combined keypad keyswitch entry to Access Levels 2 and 3. 500 event monitoring. An intuitive Windows based upload-download PC program. Up to eight XFP main panels any variant can be connected onto a two-wire RS485 non-redundantnetwork. Alternatively up to eight XFP repeaters can be connected to any non-networked main panel.Cast Commissioning Services available with this Equipment

GBP 381.44

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)