17 results (0,13781 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec CP402 CAST-PRO Heat Detector

C-Tec CP402 CAST-PRO Heat Detector

C-Tec CP402 CAST-PRO Heat DetectorA programmable CAST-PRO heat detector certified to EN54-5 17. This detector is compatible with C-TECs ZFP touchscreen-controlledCAST protocol addressable fire panel.Key FeaturesOnboard short circuit loop isolatorIncludes two 8mm x 2mm ultra-bright red LED indicatingstripsThree operation modes can be programmed to operate as anA1R A2 or B heat detector1mA alarm current570A typical quiescent current 40V DCCompatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tag

GBP 38.80
1

C-Tec CP416 CAST-PRO Smoke Detector

C-Tec CP416 CAST-PRO Smoke Detector

C-Tec CP416 CAST-PRO Smoke DetectorA programmable optical CAST-PRO fire detector designed todetect real fires quickly and reduce false alarms effectively.Key FeaturesCertified to EN54-7 17.Compatible with C-TECs ZFPtouchscreen-controlled CAST protocol addressable fire panel.MASC Miniature Advanced Smoke DetectionChamber and AFFIRM algorithms provide incredible tolerance to false alarmswhilst enhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LEDindicating strips.Two detection modes normal high sensitivity.1mA alarm current.570uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cwintegrated locking mechanism ID tag.

GBP 40.82
1

Vesda Xtralis REDFLEXI25B 25mm Flexible 1m Long Bend

Vesda Xtralis REDFLEXI25B 25mm Flexible 1m Long Bend

Vesda Xtralis REDFLEXI25B 25mm Flexible 1m Long BendWith over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Always use tools specifically designed forplastic pipe.Protective gloves are recommended for usewhen solvent cementing. If hands come into contact with cement use a waterless abrasive soap.Avoid sources of heat or open flames when solvent cementing. Do not smoke.Always chamfer and deburr pipe ends.Use the proper solvent cement note air shipments of solvent cement are forbidden by law.Always replace lids on cans when not in use.Never dilute solvent cement.Keep jointing surfaces dry in wet weather.Avoid direct inhalation of fumes. Use in a well-ventilated area.Wipe up spills or leaks immediately with clean lint free cloth or paper towels.Follow recommended cure times prior to testing the system.Prevent excessive solvent cement from running into the pipe or fitting socket.The Integrity of air sampling systems may be affected if proper CPVC solvent cement is not used. The Safety Crewdisclaims responsibility for any air sampling pipe system constructed with cements other than those recommended.Please note The PIP-021 is equivalent to the REDFLXI25B.

GBP 24.38
1

Vesda Xtralis 25mm Flexible 1m Long Bend

Vesda Xtralis 25mm Flexible 1m Long Bend

Vesda Xtralis 25mm Flexible 1m Long BendWith over 250000 aspirating smoke detectors installed worldwide the VESDA name has become synonymous with high quality and outstanding performance. An aspirating smoke detection system however only performs at its best with a well designed and installed quality pipework system. Xtralis manufacturer of VESDA detectors recognised this requirement and in 1997 launched its VESDA Pipe and Fittings range.Always use tools specifically designed forplastic pipe.Protective gloves are recommended for usewhen solvent cementing. If hands come into contact with cement use a waterless abrasive soap.Avoid sources of heat or open flames when solvent cementing. Do not smoke.Always chamfer and deburr pipe ends.Use the proper solvent cement note air shipments of solvent cement are forbidden by law.Always replace lids on cans when not in use.Never dilute solvent cement.Keep jointing surfaces dry in wet weather.Avoid direct inhalation of fumes. Use in a well-ventilated area.Wipe up spills or leaks immediately with clean lint free cloth or paper towels.Follow recommended cure times prior to testing the system.Prevent excessive solvent cement from running into the pipe or fitting socket.The Integrity of air sampling systems may be affected if proper CPVC solvent cement is not used. The Safety Crewdisclaims responsibility for any air sampling pipe system constructed with cements other than those recommended.Please note The PIP-021 is equivalent to the REDFLXI25B.

GBP 24.38
1

Nittan EV-MCP2-SCI-IP24 Reset Call Point with Short Circuit Isolator

Nittan EV-MCP2-SCI-IP24 Reset Call Point with Short Circuit Isolator

Nittan EV-MCP2-SCI-IP24 Reset Call Point with Short Circuit IsolatorEvolution Manual Call Points are available in a choice of STI ReSet IP24 EV-MCP2-SCI-IP24 Indoor Manual Call Point or IP67 housing EV-MCP2-SCI-IP67 Outdoor Manual Call Point. Both devices include Short circuit Isolator -ve Line which is a perfect solution to provide Isolation protection for a Zone. They are DIL Switch Addressed and in the case of the EV-MCP2-SCI-IP24 come with both Backbox RF Wall Plate as standard.Key FeaturesFully integrated -ve Line IsolatorEasily resettable with dedicated keySupplied with Surface Flush adaptorsSelf-resetting when fault clearsPlease note this isnt compatible with the Advanced MX pro 4 panel.

GBP 37.44
1

Fike 204-0003 Twinflex Multipoint ASD Detector

Fike 204-0003 Twinflex Multipoint ASD Detector

Fike 204-0003 Twinflex Multipoint ASD DetectorThe Multipoint and ASD detectors have set new standards in detector technology. The TWINFLEX Multipoint head is a 2-wire device used with the TWINFLEX and TWINFLEX Pro systems whereas the addressable ASD detector is used on the Sita200plus Duonet and Quadnet systems. Using microprocessor control these devices offer the installer a full range of detection capabilities with audible and visual warning in one compact device for full DDA compliance.The detectors can be matched to the environment in which they are installed and changed any time during the lifetime of the installation. The mode of detection required can be changed simply by configuring the DIL switch in the detector electronics module configurable via commissioning software on addressable systems. All modes are compliant with European detector type specifications.The TWINFLEX two-wire Multipoint detector can be set to any one of 3 smoke modes 3 heat modes as well as a Combined Mode Smoke 2 and Heat 2 where a smoke or heat source can trigger a fire decision - see opposite. The end user is given optimum fire protection even if the installer is unsure of the use of the particular area where the detector is sited. All TWINFLEX products including the Multipoint detector feature an End of Line switch negating the need for end-of-line resistors.The Multipoint and ASD detectors have the unique benefit of an optional full specification integral sounder where 90dBA output can be achieved. The two-wire Multipoint detector can be set to 3 different sound patterns as well as switched off with 2 sound output levels. The addressable ASD detector has 7 different sound patterns and 3 volume settings as well as the option of a combined strobe.Key FeaturesIntegral Strobe - The Multipoint ASD can be ordered with an optional integral strobe allowing the 2-wire installation of an advanced smokeheat detector sounder and strobe in a single cost-saving device.Base LED - When the detector head is removed a base mounted LED flashes allowing users to easily identify which head is missing even from considerable distance e.g. in a high-ceiling building.Head Removal Tool - The Multipoint ASD detector removal tool fits the Solo Detector Tester pole for easy testing and maintenance at height.Optical Chamber - The Multipoint ASD detector incorporates a new advanced optical chamber for enhanced smoke detection.Modes of DetectionSmoke 1 Used where ionisation detectors are normally fitted especially when there are high ceilings or a risk of free burning fires chemical stores etc. or fires that need to be detected extremely quickly.Smoke 2Used where optical detectors are normally fitted when there is a risk of a smouldering fire and for escape routes.Smoke 3Designed for use in areas that are prone to nuisance alarms. The reduced sensitivity linked with a time delay feature means that a higher concentration of smoke needs to be present for a constant time period before a fire decision is made. For example this setting is ideal for hotel bedrooms with en-suite shower rooms. The installer or service engineer can change the setting from smoke 2 to smoke 3 if nuisance alarms are a problem whilst still offering optimum protection of a smoke detection setting.Heat 1 Rate of RiseUsed where a standard rate of rise detector would normally be used.Heat 2 Standard Fixed Temperature - 58C approx. Used where a standard fixed temperature heat detector would normally be fitted suitable for kitchens etc.Heat 3 High Fixed Temperature - 90C approx. Used where a high fixed temperature heat detector would normally be fitted. Suitable for commercial kitchens boiler rooms etc.

GBP 32.12
1