mcb.dk | Få success online

Kidde Airsense Wire Burn Test Rig 9-30051

Kidde Airsense Wire Burn Test Rig 9-30051The unit incorporates a switched 230 volts A.C. input feeding the primary coil of a 200 VA transformer. The transformer has two 6 volt A.C. outputs that are connected across three output terminals. The two outer terminals are the individual 6 volt A.C. outputs and the centre terminal is a common return. This equipment is fitted to a die-cast metal enclosure that is connected to earth. The 230 volts A.C. supply plug is fitted with a 3.0 Amp fuse.Key FeaturesBS 6266 1992. Appendix A. Procedures A.3 and A.4British Telecom WNPCPG 57200 1998 Section 4.1. Formerly FP1063.4 Issue 8 Ultra-high sensitivity. Very high sensitivity.

GBP 1015.68

1

Vesda Xtralis VSP-025 Filter Cartridge for VLP VLS VLC amp VLF Pack of 20

Vesda Xtralis VSP-025 Filter Cartridge for VLP VLS VLC VLF Pack of 20The VSP-025 is a VESDA replacement filter cartridge VSP-005 for single units and VSP-025 for a pack of 20 is used to replace filter cartridges in VESDA LaserCOMPACT LaserFOCUS LaserPLUS and LaserSCANNER detectors. One model fits all detectors.Key FeaturesEasy swap replacement filterFits VLC VLF VLP and VLS VESDA detectorsAvailable singly or in packs of 2090 mm x 63 mm x 30 mm 3.5 in. x 2.5 in. x 1.2 in.Two Stage FiltrationFirst stage removes particles in excess of 20 micronsSecond stage is ultra-fine and removes more than 99 of particles of 0.3 microns or larger to provide a clean air barrier for optics protection

GBP 1392.68

1

Vesda-E VEU VEU-A00 Four Pipe Detector with LEDs Display - Silver

Vesda-E VEU VEU-A00 Four Pipe Detector with LEDs Display - SilverThe VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range 15 times greater than VESDA VLP and provision for more sampling holes provide an increased coverage in high airflow applications by up to 40.Considerably longer linear pipe runs and extended branched pipe network configurations cater perfectly to applications with higher ceilings providing an increased coverage by up to 80 whilst allowing convenient detector mounting for ease of service and maintenance. A range of revolutionary new features provide unsurpassed detection performance flexibility field programmability connectivity and reduced total cost of ownership.VEU features a robust IP40-rated enclosure and is equipped with a powerful aspirator that provides a total pipe length of 800 m 2624 ft. It is fully supported by the ASPIRE-E and Xtralis VSC software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.Key FeaturesFlair detection technology delivers reliable very early warning in a wide range of environments with minimal nuisance alarmsMulti stage filtration and optical protection with clean air barriers ensures lifetime detection performanceFour alarm levels and an ultra-wide sensitivity range deliver optimum protection for the widest range of applicationsIntuitive LCD icon display provides instant status information for immediate responseFlow fault thresholds per port accommodate varying airflow conditionsSmart on-board filter retains dust count and remaining filter life for predictable maintenanceExtensive event log 20000 events for event analysis and system diagnosticsAutoLearn smoke and flow for reliable and rapid commissioningReferencing to accommodate external environmental conditions to minimise nuisance alarmsFully backward compatible with VLP and VESDAnetRemote monitoring with iVESDA for system review and proactive maintenanceEthernet for connectivity with Xtralis software for configuration secondary monitoring and maintenanceIndustry first. Aspirating detector secondary monitoring and maintenance via WiFiUSB for PC configuration and firmware upgrade using a memory stickTwo programmable GPIs 1 monitored for flexible remote controlField replaceable sub-assemblies enable faster service and maximum uptime

GBP 3893.45

1

Fike FIK-UV-IR-F-AS11 UVIR Detector Hydrocarbon Fire Only

Fike FIK-UV-IR-F-AS11 UVIR Detector Hydrocarbon Fire OnlyThe UV-IR-F flame detector provides ultra-fast response high performance and reliable detection of a large variety of fires including hydrocarbon visible and non-visible. The UV-IR-F detects both slow-growing fires and fast eruptions of fire using improved UV-IR technology operating in all weather and light conditions.Key FeaturesHigh immunity to false alarmHydrocarbon flame detection. Spectrum response of IR radiation in the 4.0- 5.0 micron rangeUltra-fast detection within 5 milliseconds for fireballs or explosionsHigh sensitivity up to 100 ft. 30m for a 1 ft2 0.1m2 n-heptane pan fireDataEvent logger alarms faults and other relevant events are logged to non-volatile memoryBuilt-in-Test BIT Automatic and manual internal self-test of window cleanliness and the overall operation of the detectorWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detectorUV and IR warning levels - 0-20mA - Current output warning when elevated UV or IR radiation is detectedMeets NFPA 33 response requirement for flame detection within 0.5 seconds

GBP 3314.58

1

Fike FIK-IR3-HD-AS11 Triple IR Detector With HD Video Output

Fike FIK-IR3-HD-AS11 Triple IR Detector With HD Video OutputThe IR3-HD flame detector provides ultra-fast response high performance and reliable detection of all types of hydrocarbon fires visible and non-visible.The detector addresses slow growing fires as well as fast eruption of fire using improved triple IR IR3 technology. It operates in all weather and light conditions with highest immunity to false alarms.Key FeaturesHigh Immunity to False AlarmExtreme sensitivity up to 260 ft. 80m for a 1 ft2 0.1m2 n-heptane pan fireUltra-fast detection mode detection within 40 milliseconds for fireballs or explosions1.2 second detection time for 1 ft2 0.1m2 n-heptane pan fire at up to 50 ft. 15m distanceHD video output with Automatic HD video recording of fire events. DataEvent logger Alarms faults and other relevant events are logged to non-volatile memoryBuilt-in-Test BIT Automatic and manual self-test of window cleanliness and the overall operation of the detectorWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detector

GBP 4567.84

1

Fike FIK-IR3-AS11 Triple IR Detector

Fike FIK-IR3-AS11 Triple IR DetectorThe IR3 flame detector provides ultra-fast response high performance and reliable detection of all types of hydrocarbon fires visible and non-visible. The detector addresses slow growing fires as well as fast eruption of fire using improved triple IR IR3 technology. It operates in all weather and light conditions with highest immunity to false alarms.Add to that the integral event recording on top of the proven superior capabilities of Triple IR IR3 flame detection and you have a very powerful safety tool to protect your personnel plant and process.Key FeaturesHigh immunity to false alarmExtreme sensitivity up to 260 ft. 80m for a 1 ft2 0.1m2 n-heptane pan fireUltra-fast detection mode detection within 40 milliseconds for fireballs or explosions1.3 seconds detection time for 1 ft2 0.1m2 n-heptane pan fire at up to 50 ft. 15m distanceDataEvent logger alarms faults and other relevant events are logged to non-volatile memoryBuilt-in-Test BIT Automatic and manual self-test of window cleanliness and the overall operation of the detectorWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detector

GBP 3694.76

1

Fike FIK-UV-IR-AS11 UVIR Detector Hydrocarbon amp Non-Hydrocarbon Fires

Fike FIK-UV-IR-AS11 UVIR Detector Hydrocarbon Non-Hydrocarbon FiresUltra-fast detection within 5 milliseconds of fireballs or explosions the FIK-UV-IR-AS11 detects fires up to 100 ft away for a 1ft n-heptane fire. Quickly identifies hydrocarbon fuel and gas fires. Operates in all weather and light conditions triple spectrum technology provides immunity to false alarms.The UV-IR flame detector provides ultra-fast response high performance and reliable detection of a large variety of fires including hydrocarbon fires visible and non- visible as well as Hydrogen fires. The detector addresses slow growing fires as well as fast eruptions of fire using improved UV-IR technology. The detector operates in all weather and light conditions.Key FeaturesHigh immunity to false alarmHydrogen and Hydrocarbons flame detection.Ultra-fast detection mode detection within 5 milliseconds for fireballs or explosionsHigh sensitivity up to 100 ft. 30m for a 1 ft2 0.1m2 n-heptane pan fireDataEvent logger alarms faults and other relevant events are logged to non-volatile memoryBuilt-in-Test BIT Automatic and manual internal self-test of window cleanliness and the overall operation of the detectorWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detectorUV and IR warning levels 0-20mA Current output warning when elevated UV or IR radiation is detected

GBP 3037.18

1

Fike FIK-IR3-H2-HD-AS11 Triple IR Hydrogen Flame Detector With HD Video Output

Fike FIK-IR3-H2-HD-AS11 Triple IR Hydrogen Flame Detector With HD Video OutputThe IR3-H2-HD flame detector provides ultra-fast response high performance and reliable detection for a number of fires found in Energy Transition applications. The detector addresses slow growing fires as well as fast eruptions of fire using improved IR3 technology. The detector operates in all weather and light conditions.The detector provides high-definition HD video output of the monitored area with clear imaging of a fire event and of personnel at distances up to 100 ft. 30m. This allows the rescue team to be aware of the exact situation before entering the hazardous area. Video and data of events are stored and saved quickly to non-volatile memory for post incident investigation. The recordings start one minute before detection and continue for up to four minutes.Key FeaturesHigh immunity to false alarm including arc weldingUltra-fast detection mode detection within 40 milliseconds for Hydrogen fireballs or explosionsDetects hydrogen ammonia methane Syngas flames 3 infrared wavelengths with clear separation.Five selectable sensitivity levelsHD or composite video output with automatic HD video recording of eventsDataEvent logger alarms faults and other relevant events are logged to non-volatile memoryUniversal outputs 3 and 4 wire 4-20 mA sinksource Fire Auxiliary and Fault Relays RS485 port using Modbus RTUBuilt-in-Test BIT Automatic and manual self-test of window cleanliness and overall detector operationWindow heater to avoid condensation and icingStainless steel tilt mount adjustable horizontallyvertically

GBP 4874.34

1

Global Fire GEKKO-2 2 Loop Control Panel

Global Fire GEKKO-2 2 Loop Control PanelThe GEKKO Fire Alarm Control Panel is the successor of the enormously popular GFE JUNIOR panel.The GEKKO can have from 1 to 4 addressable loops. It is housed in a functional ABS plastic enclosure with only two screws used to close and secure the lid.The new graphic backlit LCD display can accommodate any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.It can naturally also communicate with our proprietary ODYSSEY Graphics Interface as well as with third party Building Management Systems through a Modbus output. It is also capable to communicate with a Repeater unit using any of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space for installing up to 7 AH 24V DC Sealed Lead Acid backup batteries providing battery supply to the GEKKO and ZEOS associated devices which boast extremely low current consumption.The Cause and Effect programming as well as all customer specific configuration is introduced in the GEKKO using the CHAMELEON CONNECTOR software which is then downloaded to the Flash Memory of the unit.Key Features2 loop panelNetworkable panel compatible with OCTO and NODE range of panelsSupports connection to Repeaters via RS422 Fibre-Optic or TCPIP250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limit32 individually programmable sounder addressesFull Self-Addressable Devices support2 Fire output relays change-over and 1 Fault relay NC - opens on fault2 conventional alarm outputs individually programmableBoth detection loops monitored for integrity384 fully programmable zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all our own low cost ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indication

GBP 671.47

1

Fike FIK-UV-IR-HD-AS11 UVIR Detector With HD Video Output Hydrocarbon amp Non-Hydrocarbon

Fike FIK-UV-IR-HD-AS11 UVIR Detector With HD Video Output Hydrocarbon Non-HydrocarbonThe UV-IR flame detector provides ultra-fast response high performance and reliable detection of a large variety of fires including hydrocarbon fires visible and non- visible as well as Hydrogen fires. The detector addresses slow growing fires as well as fast eruptions of fire using improved UV-IR technology. The detector operates in all weather and light conditions.The detector provides high-definition HD video output of the monitored area with clear imaging of a fire event and of personnel at distances up to 100 ft. 30m allowing rescuers to know the exact situation before entering the hazardous area. It will automatically record a video of a fire event 1 min pre-alarm up to 3 min post-alarm.Add to that the integral HD quality video with event recording on top of the proven superior capabilities of UV-IR flame detection and you have a very powerful safety tool to protect your personnel plant and process.Key FeaturesHigh immunity to False AlarmUltra-fast detection mode detection within 5 milliseconds for fireballs or explosionsHydrogen and Hydrocarbons flame detectionHigh sensitivity up to 100 ft. 30m for a 1 ft2 0.1m2 nheptane pan fireHD video output with Automatic HD video recording of fire events. DataEvent logger Alarms faults and other relevant events are logged to non-volatile memoryEthernet communication in addition to the standard methods such as 4-20mA and ModbusBuilt-in-Test BIT Automatic and manual internal self-test of window cleanliness and the overall operation of the detector for both IR and UV channelsWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detectorUV and IR warning levels 0-20mA Current output warning when elevated UV or IR radiation is detected

GBP 3938.11

1

Vesda-E VEU VEU-A10 4-Pipe Smoke Detector with 3.5quot Touchscreen Display

Vesda-E VEU VEU-A10 4-Pipe Smoke Detector with 3.5 Touchscreen DisplayThe VEU series of aspirating smoke detectors are the premium detector of the VESDA-E range. An Ultra-wide sensitivity range 15 times greater than VESDA VLP and provision for more sampling holes provide an increased coverage in high airflow applications by up to 40.Considerably longer linear pipe runs and extended branched pipe network configurations cater perfectly to applications with higher ceilings providing an increased coverage by up to 80 whilst allowing convenient detector mounting for ease of service and maintenance. A range of revolutionary new features provide unsurpassed detection performance flexibility field programmability connectivity and reduced total cost of ownership.VEU features a robust IP40-rated enclosure and is equipped with a powerful aspirator that provides a total pipe length of 800 m 2624 ft. It is fully supported by the ASPIRE-E and Xtralis VSC software applications which facilitate ease of pipe network design system commissioning and maintenance together with compatibility with existing VESDA installations.Key FeaturesShort wavelength laser based detectionInherent absolute calibrationAdvanced Imaging technology equivalentto thousands of sensorsClean air barrier for optics protectionMost robust contamination resistanceUltra-wide sensitivity rangeFlow fault thresholds configurable per portLong-life easy-to-replace filterQuiet operationLEDs for alarm and fault signalling3.5 colour touch screen for status reviewAdvanced remote diagnosticsArea coverage up to 6500m 69960ftUp to four inlet pipesTotal pipe length of 800m 2624ftSeven programmable relaysTwo GPIs monitored and unmonitoredUltrasonic flow sensingXtralis VSC VSM4 and ASPIRE-E PC software supportIP 40 enclosure not UL testedEasy mounting with optional steel supportbracketField replaceable aspirator sampling module filter anddetection chamberVESDAnet networkingEthernet 100 base TWiFi 802.11 bgnLocal host-mode USB portEasy cable termination accessEvent Log 20000 events

GBP 4616.03

1

Fike FIK-UV-IR-F-HD-AS11 UVIR Detector With HD Video Output Hydrocarbon Fires Only

Fike FIK-UV-IR-F-HD-AS11 UVIR Detector With HD Video Output Hydrocarbon Fires OnlyThe UV-IR-HD-F flame detector provides ultra-fast response high performance and reliable detection of a large variety of fires including hydrocarbon fires visible and non- visible. The detector addresses slow growing fires as well as fast eruptions of fire using improved UV-IR technology. The detector operates in all weather and light conditions.The detector provides high-definition HD video output of the monitored area with clear imaging of a fire event and of personnel at distances up to 100 ft. 30m allowing rescuers to know the exact situation before entering the hazardous area. It will automatically record a video of a fire event 1 min pre-alarm up to 3 min post-alarm.Add to that the integral HD quality video with event recording on top of the proven superior capabilities of UV-IR flame detection and you have a very powerful safety tool to protect your personnel plant and process.Key FeaturesHigh immunity to false alarmHydrocarbon flame detection. Spectrum response of IR radiation in the 4.0-5.0 micron rangeUltra-fast detection mode detection within 5 milliseconds for fireballs or explosionsHigh sensitivity up to 100 ft. 30m for a 1 ft2 0.1m2 nheptane pan fireHD video output with Automatic HD video recording of fire events. Data Event logger alarms faults and other relevant events are logged to non-volatile memoryEthernet communication - in addition to the standard methods such as 4-20mA and Modbus.Built-in-Test BIT Automatic and manual internal self-test of window cleanliness and the overall operation of the detectorWindow heater to avoid condensation and icingTilt mounting bracket can be connected either above or below the detectorUV and IR warning levels 0-20mA Current output warning when elevated UV or IR radiation is detected

GBP 3938.11

1

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop Control Panel Anthracite

Global Fire Equipment GEKKO-2BLK GEKKO 2 Loop ControlPanel AnthraciteThe GEKKO Fire Alarm Control Panel is the successor to GFEswell-known JUNIOR V4 panel.The GEKKO can have from 1 to 4 addressable loops. It ishoused in a functional ABS plastic enclosure with only two screws used toclose and secure the lid.The new graphic backlit LCD display can accommodate any typeof custom characters or graphic symbols allowing multi-language support aswell as visual and customisable elements.It can communicate with our proprietary ODYSSEY GraphicsInterface as well as with third party Building Management Systems through aModbus output. It is also capable of communicating with a repeater unit usingany of the networking interfaces of the CHAMELEON protocol.Inside the cabinet there is space to install up to 7 AH 24VDC Sealed Lead Acid backup batteries providing battery supply to the GEKKO andZEOS associated devices which boast extremely low energy consumption.The Cause and Effect programming as well as allcustomer-specific configuration is introduced in the GEKKO using the CHAMELEONCONNECTOR software which is then downloaded to the flash memory of the unit.Key FeaturesSuccessor to GFEs JUNIOR V4 panel1 to 4 loop panel 2 loop cards installedSupports connection to Repeaters via RS422 Fibre-Optic orTCPIPNetworkable panel compatible with OCTO and NODE range ofpanelsUp to 250 devices per loop only 125 addresses availableUp to 95 VULCAN 2 addressable ultra low current basesounders 32 address limit32 individually programmable sounder addressesFull self-addressable devices support2 Fire output relays change-over and 1 fault relay NC -opens on fault2 conventional alarm outputs Individually programmableBoth detection loops monitored for integrity512 fully programmable sounder and IO groups384 fully programmable zonesEvent log rolling 10000 entriesAvailable only with ZEOS protocolCompatible with all GFE manufactured ancillary modulesBacklit graphical LCD display of 240x64 pixelsProgramming by integrated keypad or Loader PC softwareMultiple language support menu selectableIntegrated 16 zone LED fire zone indicationEN54-13 EN54-2 EN54-4 1328-CPR-0737 certified

GBP 671.47

1

Global Fire OCTO-2BLK OCTO 2 Loop Control Panel - Black

Global Fire OCTO-2BLK OCTO 2 Loop Control Panel - BlackThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable ChassisColour Black

GBP 1219.99

1

Global Fire OCTO-4 Loop Control Panel

Global Fire OCTO-4 Loop Control PanelThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable Chassis

GBP 1446.26

1

Global Fire OCTO-2 OCTO 2 Loop Control Panel

Global Fire OCTO-2 OCTO 2 Loop Control PanelThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable Chassis

GBP 1157.02

1

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - Anthracite

Global Fire Equipment OCTO-4BLK 4 Loop Control Panel - AnthraciteThe OCTO Fire Alarm Control Panel is built on the pedigree of the worldwide known JUNO NET. Now featuring a fully peer-to-peer multi-master networking solution.This new Chameleon Network solution enables extreme resilience in very large distributed systems. On a Chameleon Network system each network NODE has in its internal configuration memory the whole system information i.e. in the unlikely event of a communication loss there is no performance degradation of individual NODE.The network layout is usually configured in a closed loop or having physical multi-paths for communications redundancy which can use either RS422 or Fibre-Optic mediums.It can also use Ethernet interfaces which can use the existing networking infrastructure.A Chameleon Network can accommodate up to 32 NODE. Each OCTO panel can support from 1 to 4 addressable loops giving a total of 128 loops in a single systemNaturally it also supports remote access with our proprietary ODYSSEY Graphics Interface as well as integration with third party Building Management Systems through a Modbus output.The graphic backlit LCD display accommodates any type of custom characters or graphic symbols allowing multi-language support as well as pictorial and customisable elements.Housed in an aluminium back box with a reversible plastic lid it comprises a PSU a Front End Display for visualisation of the CI equipment status a NODE unit with the loop card fitted and networking interfaces if necessary.For each 4 loops there is space for installing up to 12 AH 24V DC Sealed Lead Acid backup batteries more than enough to provide up to 24 H battery supply to the NODE and ZEOS associated devices which boast extremely low current consumption.Take into account that all networked panels share the complete system knowledge. On a multi OCTO networked panels as far as the network architecture is concerned if no human-machine Interface is needed at a specific location instead of using a complete OCTO panel with display built in a simple NODE panel can be used.By having the same 4 Loops available and housed in the same aluminium back box without the Front End Display built in the lid the NODE offers the possibility to extend the system keeping the human interface access only available at specific locations.In addition to this each NODE has provision to communicate with a remote Repeater unit using any of the networking interfaces.The Cause and Effect programming as well as customer specific Configurations can be uploaded to any OCTO panel in the network using the CHAMELEON CONNECTOR software tool. This is done by USB connection. Later the updated panel can broadcast the same configuration to all other Chameleon Network panels.Key Features1 to 4 loops panelUp to 250 devices per loop 125 address limitUp to 95 VULCAN 2 addressable ultra low current base sounders 32 address limitSupports connection to Repeaters via RS422 Fibre-Optic or TCPIPNetworked system up to 128 loopsChameleon Peer-to-Peer Advanced Networking Protocol with up to 32 NODE32 individually programmable sounder addressesSupport of Non-European languages Mandarin Arabic Hindu Urdu Farsi etc.Full Self-Addressable Devices supportBuilt in Fire Fault relays2 conventional alarm outputs individually programmableDetection loops monitored for integrity384 fully programmable multi loop zones512 fully programmable sounder groups512 IO groupsEvent log rolling 10000 entriesRemovable ChassisBlack version

GBP 1518.88

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)