60 results (0,16012 seconds)

Show all filters

Brand

Colour

Show all

Size

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

1218 2H Propane Heating Nozzle

1218 2H Propane Heating Nozzle

These heating nozzles are designed to provide large volumes of heat for applications such as bending, straightening, pre-heating, brazing, shrinking, forming and many others. They can be used to braze or silver-solder large pipes, or can be used for heating castings. Smaller sizes are often used for brazing or for applying hard-facing metal to large areas. Heating nozzles deliver significant cost-savings by providing great amounts of quick, concentrated heat. They help to do the job faster and cut labour time to a minimum.

GBP 9.99
1

99721 Shaft Repair Sleeve 180.01 x 33

99721 Shaft Repair Sleeve 180.01 x 33

Quickly and economically repair grooved and worn shafts for rotary oil seals. Fitting new seals on already worn shafts can result in repeat replacement of the seals. Grooving wear on a shaft can require expensive re-machining or even result in the shaft having to be replaced. Repair sleeves are simply pushed over the worn running surface. No special equipment is required - a standard depth installation tool is supplied with the sleeve. A mallet and a pair of pliers are all that are required for the repair job. The surface is machined without directionality, wear resistant often a better finish than that of the original shaft. Worn shaft with groove. Shaft repair sleeve in place. Restored shaft with rotary seal running on the sleeve.

GBP 79.99
1

FT33 Bearing Fitting Tool

FT33 Bearing Fitting Tool

The simatool bearing fitting tools are designed for the fast, precise and secure mounting of bearings with bore diameters from 10 to 50 mm. The right combination of impact rings and impact sleeves makes sure that the mounting forces never go through the rolling elements of a bearing. The Fitting Tool FT 33 is for careful mounting of roller bearings and radial shaft seals. Universal use for bearings with a bore diameter from 10 to 50 mm. Easily carried in a handy case, including a recoilless hammer. 3 impact sleeves and 33 impact rings No mechanical damage of the bearing Also suitable for the mounting of sleeves, sealing rings, pulleys and much more

GBP 609.99
1

24/10 Genesi M Dental Compressor 2 Chairs, 120 L/Min 5Bar, 65 dB (A) with Dryer

24/10 Genesi M Dental Compressor 2 Chairs, 120 L/Min 5Bar, 65 dB (A) with Dryer

24/10 GENESI M WITH DRYER Code: M-D-GE150-024-M Model: 24/10 Genesi M With Dryer Weight: 33 kg HIGHLIGHTS: Main features: Main features: Oil Free Compact design Receiver Size - 24Lt Noise level as low as 65 dB (A) Suitable for a dental practice with 2 dental chairs Ideal for the small lab, dental surgery, or process where air quality is critical Air quality suitable for a system in compliance with HTM 2022 ISO8573.1 Class 1-3-1 - Particles below 0.1 micron, zero oil trace Membrane dryer provide a dewpoint of up to -20 oC Simple control SPECIFICATION Chairs 2 c.f.m 4.2 L/min 120 Hp 1.5 kW 1.1 Bar 8 Psi 145 dB (A) 65 Volt 230 Receiver Size 24Lt Product L x W x H (mm) 500 x 420 x 600 Kg 33

GBP 1839.99
1

M14X2.00MM Chaser Die 20M M D/HD Type S20

M14X2.00MM Chaser Die 20M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 123.99
1

3/4" BSW Chaser Die 20MMD/HD Type S20

3/4" BSW Chaser Die 20MMD/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 119.99
1