mcb.dk | Få success online

Verplas Thermal Rectangular Pipe

Verplas Thermal Rectangular Pipe Product Part Number 1 x Meter of 204x60mm rectangular pipe - SST-204-1M 1 x Meter of 220x90mm rectangular pipe - SST-220-1M-IND Description The Verplas Self-Seal thermal 1 meter duct is manufactured from graphite impregnated expanded Polystyrene. Supplied with duct to duct connector to fit into the next set of duct. The open end of the duct is designed to push-fit over a 204x60mm/220/90mm fan spigot. It is possible to cut the length to allow for a duct to fitting to push lock and click into a female coupling. Pipe meets thermal conductivity requirements of BASF-EN13163 as well as exceeding the requirements of DW/143 Class A for low leakage. Available Sizes 204x60mm 220x90mm

GBP 21.80

1

Verplas Thermal Round Pipe

Self-Seal Thermal pipe complete with 1 click and lock duct to duct ﬁtting Product Part Number 1 meter Thermal Pipe - SST-125-1M 1 meter Thermal Pipe - SST-160-1M-IND Description Please note that any small orders below 20 meters may only be supplied in one meter lengths (excluding complete orders over £500) The Verplas Self-Seal Thermal is manufactured from Neopor Reg; graphite impregnated expanded polystyrene (EPS) with infrared absorbers and reﬂectors which signiﬁcantly improve the thermal resistance of the material compared with standard EPS. The Neopor ® material is fully tested to meet the thermal conductivity requirements of BASF – EN13163 to assist with the prevention of condensation and is Flame Retardant to DIN 4102 B1. Verplas Thermal Ducting has a minimum Density of 25 kg/m³ and therefore achieves a Thermal Conductivity of 0.03 W/mK, which at 20mm thickness, provides a minimum Thermal Resistance or R value of 0.666 m²K/W. This exceeds the current UK Domestic Ventilation Regulation requirements of Part F 2010 Domestic Ventilation Compliance Guide and NHBC Guidance Document Chapter 3.2 which states that the Thermal Resistance of the insulating material should be equivalent to a minimum 25mm of insulating material with a thermal conductivity of 0.04 W/mK which gives a minimum Thermal Resistance requirement of 0.625 m²K/W.EPP Please note that this pipe can be damaged if stood on or heavy weight is applied. Available Sizes 125mm 160mm

GBP 21.19

1

Verplas Thermal Round Pipe 90o Bend

Verplas Thermal Round Pipe 90º Bend Product Part Number 125mm 90º Round Bend - SST-125-90B 160mm 90º Round Bend - SST-160-90B-IND Description Self-Seal Thermal 90° bend complete with click and lock ﬁttings The Verplas Self-Seal Thermal is manufactured from Neopor Reg; graphite impregnated expanded polystyrene (EPS) with infrared absorbers and reﬂectors which signiﬁcantly improve the thermal resistance of the material compared with standard EPS. The Neopor ® material is fully tested to meet the thermal conductivity requirements of BASF – EN13163 to assist with the prevention of condensation and is Flame Retardant to DIN 4102 B1. Verplas Thermal Ducting has a minimum Density of 25 kg/m³ and therefore achieves a Thermal Conductivity of 0.03 W/mK, which at 20mm thickness, provides a minimum Thermal Resistance or R value of 0.666 m²K/W. This exceeds the current UK Domestic Ventilation Regulation requirements of Part F 2010 Domestic Ventilation Compliance Guide and NHBC Guidance Document Chapter 3.2 which states that the Thermal Resistance of the insulating material should be equivalent to a minimum 25mm of insulating material with a thermal conductivity of 0.04 W/mK which gives a minimum Thermal Resistance requirement of 0.625 m²K/W.EPP Please note that this pipe can be damaged if stood on or heavy weight is applied. Available Sizes 125mm 160mm

GBP 25.15

1

Verplas Thermal Round Pipe Duct to Fitting Connectors

Verplas Thermal Round Pipe Duct to Fitting Connector(Click and Lock Mechanism) Product Part Number 125mm Thermal Connector - SST-125-DFCON 160mm Thermal Connector - SST-160-DFCON Description Duct connector is manufactured with thermal resistance in mind and exceeds the thermal resistance compliance tests. The rapid self seal technology is designed to increase the pace in which a ventilation system can be installed. Components within the range of thermal self seal also exceed the requirements set out in the DW/143 Class A leakage test. Available Sizes 125mm 160mm

GBP 2.47

1

Verplas Thermal Round Pipe T-Piece

Self-Seal Thermal T Piece complete with click and lock ﬁttings Product Part Number 125mm Thermal T-Piece - SST-125-TP 160mm Thermal T-Piece - SST-160-TP-IND Description The Verplas Self-Seal Thermal is manufactured from Neopor Reg; graphite impregnated expanded polystyrene (EPS) with infrared absorbers and reﬂectors which signiﬁcantly improve the thermal resistance of the material compared with standard EPS. The Neopor ® material is fully tested to meet the thermal conductivity requirements of BASF – EN13163 to assist with the prevention of condensation and is Flame Retardant to DIN 4102 B1. Verplas Thermal Ducting has a minimum Density of 25 kg/m³ and therefore achieves a Thermal Conductivity of 0.03 W/mK, which at 20mm thickness, provides a minimum Thermal Resistance or R value of 0.666 m²K/W. This exceeds the current UK Domestic Ventilation Regulation requirements of Part F 2010 Domestic Ventilation Compliance Guide and NHBC Guidance Document Chapter 3.2 which states that the Thermal Resistance of the insulating material should be equivalent to a minimum 25mm of insulating material with a thermal conductivity of 0.04 W/mK which gives a minimum Thermal Resistance requirement of 0.625 m²K/W.EPP Please note that this pipe can be damaged if stood on or heavy weight is applied. Available Sizes 125mm 160mm

GBP 33.46

1

Ducting Condensation Trap

Ducting Condensation Trap Product Part Number 100mm PVC Condensation Trap - CD100 125mm PVC Condensation Trap - CD125 Description For Control of condensation/moisture In ducted ventilation systems Condensation will occur when warm, humid air extracted from the bathroom, shower, kitchen or utility room hits the cooler surface of your ventilation duct. If the extracted air is significantly cooled and you have a vertical pipe the moisture will condense back to water and become trapped in your ducting, potentially causing damage to the fan and property. Systems using Roof Vents or Ducting rising vertically carrying extract air to outside benefit with the use of a condensate trap, this is to prevent any moisture forming inside the ductwork, dropping back down and into the fan unit. This should then be connected to a suitable soil vent pipe using a 21.5mm overflow pipe. Constructed of PVC Compatibility Compatible with most manufactures including 100mm 125mm 150mm Verplas VKC434 VKC445 - Vent-Axia 563516 455191 455190 Manrose 1440 1450 1460 Domus 497

GBP 18.70

1

Verplas Thermal 45o Bend

Verplas Thermal 45º Bend Product Part Number 125mm Self-Seal Thermal 45° Bend - SST-125-45B 160mm Self-Seal Thermal 45° Bend - SST-160-45B-IND Description Self-Seal Thermal 45° bend complete with click and lock ﬁttings The Verplas Self-Seal Thermal is manufactured from Neopor Reg; graphite impregnated expanded polystyrene (EPS) with infrared absorbers and reﬂectors which signiﬁcantly improve the thermal resistance of the material compared with standard EPS. The Neopor ® material is fully tested to meet the thermal conductivity requirements of BASF – EN13163 to assist with the prevention of condensation and is Flame Retardant to DIN 4102 B1. Verplas Thermal Ducting has a minimum Density of 25 kg/m³ and therefore achieves a Thermal Conductivity of 0.03 W/mK, which at 20mm thickness, provides a minimum Thermal Resistance or R value of 0.666 m²K/W. This exceeds the current UK Domestic Ventilation Regulation requirements of Part F 2010 Domestic Ventilation Compliance Guide and NHBC Guidance Document Chapter 3.2 which states that the Thermal Resistance of the insulating material should be equivalent to a minimum 25mm of insulating material with a thermal conductivity of 0.04 W/mK which gives a minimum Thermal Resistance requirement of 0.625 m²K/W.EPP Please note that this pipe can be damaged if stood on or heavy weight is applied. Available Sizes 125mm 160mm

GBP 6.59

1

125mm PVC Self Seal Connector Duct to Duct

125mm PVC Self Seal Connector Duct to Duct Product Part Number 125mm duct to duct connector - VSSC125PP Description Our range of plastic ducting is UK manufactured with top quality materials that will supply a durable product suitable for domestic and commercial systems It is perfectly suited for ducting your Ventilation system, Kitchen extractor fan, bathroom fan or In-Line Extract Fans It can be used as a part of a long ductwork run for a variety of purposes including whole house ventilation, passive stack vent, positive input, air conditioning, HVAC, and Heat Recovery Systems KEY FEATURES: UK Manufactured Pipe ends are female and will accept male fittings such as bends and grilles Lengths of duct channel can be joined together using a male connector Easy to install and durable, just push-fit duct and fittings together Compatible with most other manufactures Extensive range of fittings, outlets, and grilles available Max / Min Temperature: +60c / -15c DW/154 and meets UL94HB Flammability standard Suitable to use in compliance with Part F Building Regulations Sap Appendix Q Compliant Airflow performance independently tested by BSRIA or BRE Performance Solid Rigid ducting systems are suitable for use in all buildings to provide superior airflow performance vs. comparative size rectangular or flexible pvc or Aluminium duct. Suitable to use in compliance with Part F Building Regulations. Insulation of Ductwork It is important that any ducting located in a cold area (e.g. loft space) to be insulated. The insulation needs to be the equivalent of 25mm thick and have a thermal conductivity of 0.04W/(m.k) or less. This ensures that condensation doesn’t form due to the difference in air temperature inside the duct when compared to the air temperature in the cold space.

GBP 10.13

1

Short Round to Rectangular Adaptor Female

110x54mm - Short Round to Rectangular Adaptor Female Product part Number Short Round Female Adaptor - AS110100 Description Adaptor for 100mm round female spigot to 110mm x 54mm rectangular duct pipe Our range of plastic ducting is UK manufactured with top quality materials that will supply a durable product suitable for domestic and commercial systems It is perfectly suited for ducting your ventilation system, kitchen extractor fan, bathroom fan or in-line extract fans It can be used as a part of a long ductwork run for a variety of purposes including whole-house ventilation, passive stack vent, positive input, air conditioning, HVAC, and heat recovery systems. Performance Solid Rigid ducting is suitable for use in all buildings to provide superior airflow performance vs. comparative size rectangular or flexible PVC or aluminium duct. Suitable to use in compliance with Part F Building Regulations. Installation To provide the best performance in airtightness and durability we recommend You provide greater mechanical strength to a joint by using a combination of plastic ducting sealant and aluminium duct sealing tape Apply duct sealant to the male fitting Push together Apply aluminium duct sealing tape over joint Alternatively, you can use self-sealing fittings that speed up the time taken by up to 70% and can be easily dismantled Insulation of Ductwork It is important that any ducting located in a cold area (e.g. loft space) to be insulated. The insulation needs to be the equivalent of 25mm thick and have a thermal conductivity of 0.04W/(m.k) or less. This ensures that condensation doesn’t form due to the difference in air temperature inside the duct when compared to the air temperature in the cold space. If you don’t have a loft space there is still a need for insulated ducting on the intake and exhaust legs, as they will be carrying cold air in a warm space. The level of insulation can be achieved by wrapping PVC duct in a layer of 25mm duct wrap that has a silver foil face on a 25mm Rockwool It is also worth noting that foil wrap with air bubbles (bubble wrap) is no longer applicable in building control regulations Available Sizes 110x54mm rectangular to 100mm

GBP 2.96

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)