mcb.dk | Få success online

System Sensor M200XE Loop Isolation Module

System Sensor M200XE Loop Isolation ModuleThere is a large number of System Sensor intelligent fire alarm systems the address loop with a recipient device up to 198 is protected by a single one loop interruption but in the case of loop short circuit the entire loop it may become inoperable. With the M200XE modules shorting is not desired can be reduced.Only a small part of the system falls out if the loop is broken down into isolators because in the case of a possible loop only the two isolators will not be available to the control panel. If the address loop voltage drops below 7V the isolator module - with FET on the branch breaks it off the loop in the non-short-term part of the address loop the assets remain operational. If the breakdown the loop voltage rises on one side of the module then the separated short-circuit loop section 3 mA max. 15 mA control current flows through the module.In isolation the address loop wires between min. 2.2 kOhm resistance. The isolated state is maintained until the voltage of the disconnected section is 7V the short-circuit or the abnormally high current consumption ceases to exist. After the termination of the termination the isolator disengages the loop automatically.The two-colour LED on the module flashes green in the normal state of the loop every 3 seconds. If the module on any side it detects a short-circuit it illuminates with continuous yellow light during the shutter. The M200XE module in the M200E-SMB mounting box is wall-mounted with the M200E-DIN clip directly on the DIN rail M200E-PMB clip can be mounted in the fire panels box.

GBP 55.08

1

System Sensor BSO-PP-I00 Base Sounder with Loop Isolation

System Sensor BSO-PP-I00 Base Sounder with Loop IsolationBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 58.90

1

System Sensor WSO-PP-I00 Wall Mounted White Sounder with Loop Isolation

System Sensor WSO-PP-I00 Wall Mounted White Sounder with Loop IsolationWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 61.27

1

System Sensor WSO-PR-I00 Wall Mounted Red Sounder with Loop Isolation

System Sensor WSO-PR-I00 Wall Mounted Red Sounder with Loop IsolationWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 55.08

1

System Sensor DSS-PC-I00 Base Sounder VAD with Loop Isolation

System Sensor DSS-PC-I00 Base Sounder VAD with Loop IsolationEN54-23 Detector Base Sounder Strobe is a high-quality loop powered device intended to alert building occupants of a potential fire. Approved to meet EN54-23 the European standard for Visual Alarm Devices it utilizes the System Sensor B501AP base for enhanced installation flexibility and integrates seamlessly with System Sensor intelligent detectors.When triggered by the fire panel its powerful sounder and intense strobe give a visible and audible warning. A choice of sound output levels and tones make the device suitable for a wide variety of applications.Key FeaturesHigh output LED technology ensures optimum light output and low power requirementsHigh efficiency piezo disk and horn profile generate powerful sound outputFeatures Advanced protocol controllable sound output tone selection group polling independent sound or strobe functionAutomatic synchronization of sounder and strobeLarge cable accessRear or surface cable entryLoop continuity springSimple twist fit onto universal B501AP base positive poke yoke engagementAnti-tamper featureIn-built isolation optionsAddress tag for clear indicationSingle point of installation saves time cost inventoryLow current draw enables more devices on loopAdjustable volume control on device or from panelRotary wheels for clear address indicationClear lens with red flash

GBP 93.70

1

System Sensor BSO-PP-I00-B Base Sounder with Loop Isolation With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor BSO-PP-I00-B Base Sounder with Loop Isolation With BaseBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501AP - includedDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 49.67

1

System Sensor IM-10EA Ten Input Monitor Module

System Sensor IM-10EA Ten Input Monitor ModuleThe IM-10EA Ten Input Monitor Module is intended for use in an intelligent alarm system. Each monitor module is intended to interface between a control panel and normally open contact devices such as pull stations. A common SLC input is used for all modules and the initiating device loops share a common supervisory supply and ground.Otherwise each monitor operates independently from the others. Each module also has panel-controlled tri-colour green red and amber LED indicators. The panel can cause the LEDs to blink latch on or latch off. The module also provides short circuit isolators to prevent shorts on the fire detection and alarm system loop from disabling more than one device on the intelligent loop.

GBP 538.40

1

System Sensor M200G-RF-26 Agile Gateway

System Sensor M200G-RF-26 Agile GatewayLoop-powered Gateway device for System Sensor Agile wireless system. Up to 8 Gateways may be used on the same loop. This requires a B501AP base. Compatible with DXc panels only.The System Sensor M200G-RF is a loop powered gateway unit from the Agile range of wireless fire system equipment. This device is designed to communicate with the System Sensor Agile range of wireless fire system devices.The Agile wireless platform is powered by robust mesh network technology providing up to two communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. Mesh network technology enables flexible and economic installations in a wide variety of building footprints.Key FeaturesRequires a B501AP basePlease NoteThis panel is compatible with the Morley System Sensor DXc panel range only.

GBP 289.18

1

System Sensor Agile Wireless Gateway Device M200G-RF

System Sensor Agile Wireless Gateway Device M200G-RF The System Sensor M200G-RF is a loop powered gateway unit from the Agile range of wireless fire system equipment. This device is designed to communicate with the System Sensor Agile range of wireless fire system devices.The Agile wireless platform is powered by robust mesh network technology providing up to two communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. Mesh network technology enables flexible and economic installations in a wide variety of building footprints.Please NoteThis panel is compatible with the Morley System Sensor DXc panel range only.

GBP 255.80

1

System Sensor WSS-PR-I00 Wall Mounted Sounder Strobe With Isolator - White Skirt

System Sensor WSS-PR-I00 Wall Mounted Sounder Strobe With Isolator - White SkirtThe WSS-PR-I00 is a wall mounted sounder strobe with integral isolator.The beacon has fast and simple installation and is control powered by the fire panel via the loop wiring. The control of the device is enabled using on-board switches or via the digital protocol using the control panel.Key FeaturesWall Mounted Addressable Sounder StrobeColour White Body Red LensIntegral IsolatorFast and simple installationPlease note This product is not approved to EN54-23 Visual Alarm Device and must not be used as a visual alarm device to provide a primary warning notification of fire.

GBP 86.93

1

System Sensor WST-PC-N00 Wall Mounted VAD Clear Lens with Red Flash

System Sensor WST-PC-N00 Wall Mounted VAD Clear Lens with Red FlashWall mount strobe is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its intense strobe gives a highly visible warning. A choice of lens colours makes the device suitable for a wide variety of applicationsKey FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of strobePositive poke yoke engagementAddress tag for clear indicationAnti-tamper featureSimple familiar rotary wheel address controlsCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols

GBP 38.52

1

System Sensor WSO-PR-N00 Wall Mounted Red Sounder

System Sensor WSO-PR-N00 Wall Mounted Red SounderWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 47.51

1

System Sensor WSO-PP-N00 Wall Mounted White Sounder

System Sensor WSO-PP-N00 Wall Mounted White SounderWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 50.95

1

System Sensor M201EA Output Control Module

System Sensor M201EA Output Control ModuleThe System Sensor M200 wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The new M200 look and feel combine maximum reliability with top-end functionality. Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure.Key FeaturesCommon mechanical platform for modules enclosureLow standby currentFACP reads module power voltageHigh Power Loop 48V readyBuilt-in short circuit isolatorsAddressability through rotary switchesTri-colour Light PipeImproved Light Pipe visibility on two sidesPlug-in field wiring terminalsIntegrated DIN rail bracketsLasered engraved label dataIP rate 30Intertek ApprovedPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 68.16

1

System Sensor M221EA Dual Input and Single Control Output Combination Module

System Sensor M221EA Dual Input and Single Control Output Combination ModuleThe System Sensor M200 wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The new M200 look and feel combine maximum reliability with top-end functionality. Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure.Key FeaturesCommon mechanical platform for modules enclosureLow standby currentFACP reads module power voltageHigh Power Loop 48V readyBuilt-in short circuit isolatorsAddressability through rotary switchesTri-colour Light PipeImproved Light Pipe visibility on two sidesPlug-in field wiring terminalsIntegrated DIN rail bracketsLasered engraved label dataIP rate 30Intertek ApprovedPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 128.75

1

System Sensor BSO-PP-N00 Base Sounder

System Sensor BSO-PP-N00 Base SounderBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 48.12

1

System Sensor WSO-PR-N00-B Wall Mounted Red Sounder With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor WSO-PR-N00-B Wall Mounted Red Sounder With BaseWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 50.81

1

System Sensor WSO-PP-N00-B Wall Mounted White Sounder With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor WSO-PP-N00-B Wall Mounted White Sounder With BaseWall mount sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many marketsAddress tag for clear indicationAnti-tamper featureIn-built isolation optionsSimple familiar rotary wheel address controls

GBP 54.43

1

System Sensor M201E-B Output Control Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M201E-B Output Control Module With M200E-SMBThe M201E provides a single output that can be switched when commanded by a fire alarm control panel. In the supervised mode the M201E supervises the wiring to the load devices. Upon command from the fire alarm control panel the M201E switches an external power supply to operate these devices while de-activating the load supervision.The module raises an unlatched fault condition if the external power supply voltage falls below the fixed threshold. In the unsupervised mode the M201E provides one set of form C changeover contacts and does not provide load nor power supply supervision. The M201E has built-in short circuit protection for the communications loop which may be selecteddeselected to meet the specific requirements of each installation.Key FeaturesComes withM200E-SMBfor surface mounting

GBP 58.97

1

System Sensor BSO-PP-N00-B Base Sounder With Base

Please note The price of this product including the base is a special promotional offer directly from the manufacturer.System Sensor BSO-PP-N00-B Base Sounder With BaseBase sounder is a high-quality loop powered device designed to alert building occupants of an emergency. It utilizes the System Sensor B501AP base for improved installation flexibility and integrates seamlessly with SS intelligent detectors. When triggered by the fire panel its powerful sounder gives an audible warning. A choice of output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseLarge cable accessRear or surface cable entryLoop continuity springAutomatic synchronisation of sounderLow current draw enables more devices on loopAdjustable volume control on device or from panelIntense strobe outputDeep and high IP base optionsPure White or Ivory body coloursCommon base with detectors B501APDevice protocol is backward compatible through inclusion of both SS CLIP and Advanced Protocols32 tone selection to cover many markets on device or from panel

GBP 35.16

1

System Sensor DSS-PC-N00 Base Sounder VAD

System Sensor DSS-PC-N00 Base Sounder VADEN54-23 Detector Base Sounder Strobe is a high-quality loop powered device intended to alert building occupants of a potential fire. Approved to meet EN54-23 the European standard for Visual Alarm Devices it utilizes the System Sensor B501AP base for enhanced installation flexibility and integrates seamlessly with System Sensor intelligent detectors. When triggered by the fire panel its powerful sounder and intense strobe give a visible and audible warning. A choice of sound output levels and tones make the device suitable for a wide variety of applications.Key FeaturesHigh output LED technology ensures optimum light output and low power requirementsHigh efficiency piezo disk and horn profile generate powerful sound outputFeatures Advanced protocol controllable sound output tone selection group polling independent sound or strobe functionAutomatic synchronization of sounder and strobeLarge cable accessRear or surface cable entryLoop continuity springSimple twist fit onto universal B501AP base positive poke yoke engagementAnti-tamper featureIn-built isolation optionsAddress tag for clear indicationSingle point of installation saves time cost inventoryLow current draw enables more devices on loopAdjustable volume control on device or from panelRotary wheels for clear address indicationClear lens with red flash

GBP 76.56

1

System Sensor DSS-PC-N00-B Base Sounder VAD With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor DSS-PC-N00-B Base Sounder VAD With BaseEN54-23 Detector Base Sounder Strobe is a high-quality loop powered device intended to alert building occupants of a potential fire. Approved to meet EN54-23 the European standard for Visual Alarm Devices it utilizes the System Sensor B501AP base for enhanced installation flexibility and integrates seamlessly with System Sensor intelligent detectors. When triggered by the fire panel its powerful sounder and intense strobe give a visible and audible warning. A choice of sound output levels and tones make the device suitable for a wide variety of applications.Key FeaturesIncludes B501AP baseHigh output LED technology ensures optimum light output and low power requirementsHigh efficiency piezo disk and horn profile generate powerful sound outputFeatures Advanced protocol controllable sound output tone selection group polling independent sound or strobe functionAutomatic synchronization of sounder and strobeLarge cable accessRear or surface cable entryLoop continuity springSimple twist fit onto universal B501AP base positive poke yoke engagement - base includedAnti-tamper featureIn-built isolation optionsAddress tag for clear indicationSingle point of installation saves time cost inventoryLow current draw enables more devices on loopAdjustable volume control on device or from panelRotary wheels for clear address indicationClear lens with red flash

GBP 32.89

1

System Sensor M210EA Single Input Monitor Module

System Sensor M210EA Single Input Monitor ModuleThe newly designed platform of M200 family of Input Output modules completes the S200AP line of wired spot detectors with unaltered family feeling and undisputed continuity.The new M200 look and feel combine maximum reliability with top-end functionality all enriched by a cutting-edge modern design.Single and multi-way models are available within the renewed mechanical package reducing both the cost of installation and the mounting space required.Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure. The DIN rail mounting option is possible thanks to smart DIN brackets directly built-in the enclosure. Irrespective of the mounting methods chosen the address switch is always visible and accessible for selection.Each module has built-in short circuit protection for the communications loop however to increase application flexibility the isolators can be selecteddeselected on an individual module basis.To help technicians in the maintenance and fault-finding process light pipes have been enlarged to increase visibility even in the most challenging space constrained application. Both the status LED and the rotary switch selection can be viewed on the two sides without having to remove the cover of the surface mounting box. The multi-colour status LED provide diagnostic information regarding the status of each individual inputoutput.For ease of installation testing and maintenance modules have been equipped with quick connectors.The renovated aesthetics offers data finely engraved on the enclosures surface by laser for lifetime durability and resistance to degradation.Please note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 57.14

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)