mcb.dk | Få success online

International Gas Detectors T750BAV-O2-NHS Gas Detector with Audible Visual Alarms

International Gas Detectors T750BAV-O2-NHS Gas Detector with Audible Visual AlarmsThe TOC-750 is factory calibrated for its target gas. The target gas is indicated on the product i.e. CH4 LPG etc.The TOC-750 will respond to any flammable gas but can only be calibrated to be correct response to one.The detector front assembly simply plugs onto the indicated connector. Alarm actions are indicated on the following page for each detector type. This makes service replacement vert simple as the toxic IR detector assembly is pre-calibrated and can just be plugged in to enable operation.The detector node relay output can be used as an alarm interface to external systems run additional audio-visual alarms or directly control other devices. Typical applications could be gas solenoid valves boiler shut down interfaces or similar. When switching external loads it is important to consider the nature of the load being switched. For inductive loads suitable protection from induced back EMF must be fitted. Many modern devices conforming to the European EMC Directive may already have devices fitted as part of their design to limit in-rush currents and back EMF. Where these are not fitted the following two diagrams provide guidance. Failure to observe this may result in damage to the detector node.

GBP 392.63

1

International Gas Detectors TOC-CBL-SET Engineers Android Cable Set TOC 650 amp 750

International Gas Detectors TOC-CBL-SET Engineers Android Cable Set TOC 650 750The TOC-CBL-SET is an Engineers Android Cable Set designed for use with the TOC 650 750 range of products.International Gas Detectors provide a range of Android based apps for use with suitable tablets and mobile phones. For addressable devices it is necessary to make a direct USB cable connection using International Gas Detectors interface cable. Apps can be downloaded from the App Store.

GBP 206.55

1

International Gas Detectors Dynamic Duct Adaptor HT 5999205

International Gas Detectors Dynamic Duct Adaptor HT 5999205The HT version of the Dynamic Duct Adaptor is a development based on extensive indsutrail experience targeted specifically to overcome the problem of gas detection in a hot gas flow. The probe will interface to Tocsin 102 and MK3 series gas detectors. The detectors can either provide a conventional 4-20mA linear analogue process signal or can be networked using our addressable highway protocol. The probe system requires an airflow to induce a flow through the probe system. The probe incorporates a heat exchanger and baffle system to protect the fas detector from excessive temperature and debris. Field proven over many years the HT Duct Adaptor finds many applications in industry typical of these would be drying oven extracts.Any of the extensive 102 or MK3 series gas detectors can be used in conjunction with the probe system

GBP 2000.89

1

International Gas Detectors TOC-640-O2 Addressable Control Panel with Detector

International Gas Detector TOC-640-O2 Addressable Control Panel with DetectorThe TOCSIN 640 Addressable Control Panel with Detector is a variant of the TOCSIN 640 Detector Control Panel. The TOCSIN 640 Addressable Control Panel with Detector comes with all the features of a standard 640 system and fitted with a detector and mains lead. Available withCO2OxygenandVOC monitoring.This version of the 640 is pre-calibrated and configured with standard alarms based on HSE EH40 document. The TOCSIN 640 Addressable Control Panel withDetector is ready to use within minute of delivery with virtually no installation. The clear to read multi-colour display provides clear indication of alarm status.Green lightin normal operation flashing red on alarm and with level indication the system is simple to fit and operate. the built in window also provides clear indication of and alarm condition. Alarms automatically reset once the hazard is clear requiring no user input. This TOCSIN 640 with detector is clear simple to use effective protection and has all the features of a normal TOCSIN 640 Control Panel.The TOCSIN 640 with detector is shipped with factory calibration certificates and the gas detector fitted has a long life infrared or a polymer cell these cells typical operational life time is in excess of 5 years.This product is ideal to use inSmall surgeries for oxygen depletion monitoringIdeal forLaboratory environments clean rooms or dentistry.Background VOC monitoringKey FeaturesSupplied pre-calibrated with a wide range of sensor options including Oxygen CO2 and VOC.Easy to wall mountPre-fitted with a mains headExpand later as required with Additional detectorsRelay outputs as standard4-20mA outputsRS485 MonBusControl up to an additional 24 IGD Gas Detectors or IO Modules for future site expansion.LED display with multi coloured backlight Flashes red when the panel is in alarm the panel flashes yellow when it is in faultE-Stop inputSystem ConfigurableDedicated interlock to Fire Systems System Configurable

GBP 761.79

1

International Gas Detectors TOC-750-O2 Safe Area Gas Detector - Oxygen Sensor Standard Range 0-25 Vol

International Gas Detectors TOC-750-O2 Safe Area Gas Detector - Oxygen Sensor Standard Range 0-25 VolBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 315.51

1

International Gas Detectors TOC-750-HNH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-5000ppm

International Gas Detectors TOC-750-HNH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-5000ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 535.95

1

International Gas Detectors TOC-750-MK7 Safe Area Gas Detector - MK7 Flammable Gas Sensor Range 0-100 LEL

International Gas Detectors TOC-750-MK7 Safe Area Gas Detector - MK7 Flammable Gas Sensor Range 0-100 LELBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 161.18

1

International Gas Detectors TOC-750-O3 Safe Area Gas Detector - Ozone Sensor Range 0-5ppm

International Gas Detectors TOC-750-O3 Safe Area Gas Detector - Ozone Sensor Range 0-5ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 413.59

1

International Gas Detectors TOC-750-SIH4 Safe Area Gas Detector - Silane Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-SIH4 Safe Area Gas Detector - Silane Sensor Standard Range 0-10ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.93

1

International Gas Detectors TOC-750-CO2 Safe Area Gas Detector - CO2 Sensor High Range Standard Range 0-5

International Gas Detectors TOC-750-CO2 Safe Area Gas Detector - CO2 Sensor High Range Standard Range 0-5Building on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 453.87

1

International Gas Detectors TOC-750-H2S Safe Area Gas Detector - H2S Sensor Standard Range 0-50ppm

International Gas Detectors TOC-750-H2S Safe Area Gas Detector - H2S Sensor Standard Range 0-50ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 300.08

1

International Gas Detectors TOC-750-CL2 Safe Area Gas Detector - Chlorine Sensor Standard Range 0-5ppm

International Gas Detectors TOC-750-CL2 Safe Area Gas Detector - Chlorine Sensor Standard Range 0-5ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 430.26

1

International Gas Detectors TOC-750-NH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-500ppm

International Gas Detectors TOC-750-NH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-500ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 433.53

1

International Gas Detectors TOC-750-HCL Safe Area Gas Detector - Hydrogen Chloride Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-HCL Safe Area Gas Detector - Hydrogen Chloride Sensor Standard Range 0-10ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.93

1

International Gas Detectors TOC-750-SO2 Safe Area Gas Detector - SO2 Sensor Standard Range 0-5ppm

International Gas Detectors TOC-750-SO2 Safe Area Gas Detector - SO2 Sensor Standard Range 0-5ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 508.36

1

International Gas Detectors TOC-750-CO Safe Area Gas Detector - CO Sensor Standard Range 0-100ppm

International Gas Detectors TOC-750-CO Safe Area Gas Detector - CO Sensor Standard Range 0-100ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 276.93

1

International Gas Detectors TOC-750-BCL3 Safe Area Gas Detector - Boron Trichloride Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-BCL3 Safe Area Gas Detector - Boron Trichloride Sensor Standard Range 0-10ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.93

1

International Gas Detectors TOC-750-NO2 Safe Area Gas Detector - Nitrogen Dioxide Sensor Standard Range 0-5pp

International Gas Detectors TOC-750-NO2 Safe Area Gas Detector - Nitrogen Dioxide Sensor Standard Range 0-5ppBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 376.64

1

International Gas Detectors TOC-750-H2 Safe Area Gas Detector - Hydrogen Sensor Standard Range 0-1000ppm

International Gas Detectors TOC-750-H2 Safe Area Gas Detector - Hydrogen Sensor Standard Range 0-1000ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.93

1

International Gas Detectors TOC-750-HCO Safe Area Gas Detector - CO2 Sensor Standard Range 0-100 VV

International Gas Detectors TOC-750-HCO Safe Area Gas Detector - CO2 Sensor Standard Range 0-100 VVBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 366.50

1

International Gas Detectors TOC-750-LVOC Safe Area Gas Detector - VOC Sensor Range 200ppm Isobutylene

International Gas Detectors TOC-750-LVOC Safe Area Gas Detector - VOC Sensor Range 200ppm IsobutyleneBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 1262.25

1

International Gas Detectors TOC-750-CH2O Safe Area Gas Detector - Formaldehyde Detector Standard Range 0-5ppm

International Gas Detectors TOC-750-CH2O Safe Area Gas Detector - Formaldehyde Detector Standard Range 0-5ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.91

1

International Gas Detectors TOC-750-NO Safe Area Gas Detector - Nitric Oxide Sensor Standard Range 0-25ppm

International Gas Detectors TOC-750-NO Safe Area Gas Detector - Nitric Oxide Sensor Standard Range 0-25ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 376.64

1

International Gas Detectors TOC-750-HBR Safe Area Gas Detector - Hydrogen Bromide Sensor Standard Range 0-20ppm

International Gas Detectors TOC-750-HBR Safe Area Gas Detector - Hydrogen Bromide Sensor Standard Range 0-20ppmBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 438.93

1

International Gas Detectors TOC-750-ETO Safe Area Gas Detector - ETO Sensor Standard Range 0-10 PPM

International Gas Detectors TOC-750-ETO Safe Area Gas Detector - ETO Sensor Standard Range 0-10 PPMBuilding on IGDs existing Addressable Gas Detectors the 750 Series add 2-Wire addressable technology. Using IGDs Sentinel 2-Wire protocol the 750 Series communicate over the detector power cables. This reduces cabling and terminations whilst improving reliability. Sentinel protocol continuously monitors data between connected detectors and the system controller ensuring maximum system availability. With only two wires for power and communication existing systems can be easily upgraded using existing cables with the option to easily add more detectors where required.Tocsin 750 Series detector systems have a number of standard interfaces available on-board each unit. The standard PCB set allows interface either Toxic Oxygen or Flammable Detectors. Communication to the system controller uses IGDs latest Sentinel 2-Wire protocol for speed of installation and increased reliability. Existing analogue systems can be quickly updated to 2-Wire addressable systems. In addition each module has a flexible range of additional interfaces to easily add slam switches beacon-sounders and other readings to the system

GBP 536.56

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)

International Gas Detectors T750BAV-O2-NHS Gas Detector with Audible Visual Alarms

International Gas Detectors TOC-CBL-SET Engineers Android Cable Set TOC 650 amp 750

International Gas Detectors Dynamic Duct Adaptor HT 5999205

International Gas Detectors TOC-640-O2 Addressable Control Panel with Detector

International Gas Detectors TOC-750-O2 Safe Area Gas Detector - Oxygen Sensor Standard Range 0-25 Vol

International Gas Detectors TOC-750-HNH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-5000ppm

International Gas Detectors TOC-750-MK7 Safe Area Gas Detector - MK7 Flammable Gas Sensor Range 0-100 LEL

International Gas Detectors TOC-750-O3 Safe Area Gas Detector - Ozone Sensor Range 0-5ppm

International Gas Detectors TOC-750-SIH4 Safe Area Gas Detector - Silane Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-CO2 Safe Area Gas Detector - CO2 Sensor High Range Standard Range 0-5

International Gas Detectors TOC-750-H2S Safe Area Gas Detector - H2S Sensor Standard Range 0-50ppm

International Gas Detectors TOC-750-CL2 Safe Area Gas Detector - Chlorine Sensor Standard Range 0-5ppm

International Gas Detectors TOC-750-NH3 Safe Area Gas Detector - Ammonia Sensor Standard Range 0-500ppm

International Gas Detectors TOC-750-HCL Safe Area Gas Detector - Hydrogen Chloride Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-SO2 Safe Area Gas Detector - SO2 Sensor Standard Range 0-5ppm

International Gas Detectors TOC-750-CO Safe Area Gas Detector - CO Sensor Standard Range 0-100ppm

International Gas Detectors TOC-750-BCL3 Safe Area Gas Detector - Boron Trichloride Sensor Standard Range 0-10ppm

International Gas Detectors TOC-750-NO2 Safe Area Gas Detector - Nitrogen Dioxide Sensor Standard Range 0-5pp

International Gas Detectors TOC-750-H2 Safe Area Gas Detector - Hydrogen Sensor Standard Range 0-1000ppm

International Gas Detectors TOC-750-HCO Safe Area Gas Detector - CO2 Sensor Standard Range 0-100 VV

International Gas Detectors TOC-750-LVOC Safe Area Gas Detector - VOC Sensor Range 200ppm Isobutylene

International Gas Detectors TOC-750-CH2O Safe Area Gas Detector - Formaldehyde Detector Standard Range 0-5ppm

International Gas Detectors TOC-750-NO Safe Area Gas Detector - Nitric Oxide Sensor Standard Range 0-25ppm

International Gas Detectors TOC-750-HBR Safe Area Gas Detector - Hydrogen Bromide Sensor Standard Range 0-20ppm

International Gas Detectors TOC-750-ETO Safe Area Gas Detector - ETO Sensor Standard Range 0-10 PPM

Powered by Cobiro