mcb.dk | Få success online

Global Fire Equipment 3-LC-CHAMELEON Chameleon 3 Loop Card

Global Fire Equipment 3-LC-CHAMELEON Chameleon 3 Loop CardA 3 loop card for the Global Fire Equipment Chameleon Repeater Panel.

GBP 446.27

1

Global Fire Equipment GFE-IO-3 Addressable 3-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-3 Addressable 3-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 82.61

1

Global Fire Equipment GFE-MULTI Multi IO Module - 4 x ZMU 3 x LSC 2 x Aux. Relays

Global Fire Equipment GFE-MULTI Multi IO Module - 4 x ZMU 3 x LSC 2 x Aux. RelaysThe MULTI-IO is a fully monitored addressable module which can be used with Global Fire Addressable fire alarm control panels.The module provides four Zone Monitor Units three Sounder Units and two system auxiliary Relays.The module requires an external 24V DC power supply. A Dedicated green LED indicates if a power supply is present.The module has selectable Active or Resistive End of Line Monitoring for the Zone Monitor Units. The status of each zone is indicated by two LEDs. A Red LED signals Fire Yellow indicates Fault on that zone.Key FeaturesLoop monitored for Open Circuits Short CircuitsMaximum 32 devices per Zone1A Maximum combined current drive for S1 S2 and S3Powered from 24V external supplyFour consecutive addresses selection Zone Monitor UnitsSeven consecutive addresses selection Four Zone Monitor Units Three Sounder UnitsActive or Resistive end online

GBP 63.88

1

Global Fire Equipment GFE-IO-2 Addressable 2-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-2 Addressable 2-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 65.52

1

Global Fire Equipment GFE-IO-1 Addressable 1-Channel IO Module CW Isolator

Global Fire Equipment GFE-IO-1 Addressable 1-Channel IO Module CW IsolatorThe 3 IO PLUS Modules are fully monitored loop powered devices which permit the interfacing of third-party equipment with the FireAlarm Control panel using normally open dry contact connections. Each module can be fitted with a maximum of 3 inputs and 3 outputs. The connection to each input is monitored for fault open or short circuit and alarm conditions.The interface is used to monitor the contacts of an external system which must be interfaced to the Fire Alarm System for example a Flow Switch in a sprinkler system to indicate if the sprinklers have been activated or extinguishant level monitoring in Gas Extinguishing Systems etc.Module is provided with a loop short-circuit isolator and with up to 3 voltage free single pole change over relay outputs. The output relays are always powered directly from the detection loop. It is not required to use an external 24V DC power supply. Relay operation is confirmed by an onboard Red LED. A 8 way D.I.L. switch is provided to configure the modules address. This value can be set in the range 1 to 125. The following programmable functions are available Input Activation Mode Delayed Input Alarm Activation Output Delayed Activation.Key FeaturesFast Activation ResponseLoop PoweredStatus LEDs for each IO and OPLow Power ConsumptionModule features an integral short-circuit loop isolator

GBP 48.43

1

Global Fire Vulcan 2 CS Conventional Red Base Sounder

Global Fire Vulcan 2 CS Conventional Red Base SounderThe VULCAN 2 C is a low consumption sounder designed to be used as an unobtrusive low profile sounder or as a base sounder to be installed in conjunction with a conventional detector. This leads to reduced installation costs and improves the aesthetics of the fire alarm system.Four different tones are available and selected by jumpers. The Sound level can be adjusted if required using the potentiometer. The complete range is composed of 3 varieties in both base and wall mounted versions Beacon Sounder and combined SounderBeacon.

GBP 18.29

1

Global Fire VULCAN2-CSB VULCAN 2 Conventional Base Sounder Beacon cw Lid

Global Fire VULCAN2-CSB VULCAN 2 Conventional Base Sounder Beacon cw LidThe VULCAN 2 C is a low consumption sounder designed to be used as an unobtrusive low profile sounder or as a base sounder to be installed in conjunction with a conventional detector.This leads to reduced installation costs and improves the aesthetics of the fire alarm system. Four different tones are available and selected by jumpers.The Sound level can be adjusted if required using the potentiometer.The complete range is composed of 3 varieties in both base and wall mounted versions Beacon Sounder and combined Sounder Beacon.

GBP 31.34

1

Global Fire Valkyrie AB Addressable Red Beacon

Global Fire Valkyrie AB Addressable Red BeaconThe VALKYRIE AB is a Wall Mounted Addressable Beacon with low power consumption. Up to 32 individually addressed beacons can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8-way DIL switch.When individual address reporting is not required VALKYRIE AB can be configured as a Shadow Beacon. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow beacons do not report back to the control panel so their presence on the loop is not monitored.Shadow beacons draw current from the loop 3 mA in alarm and must be included in loop load calculations. These units are produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.

GBP 37.91

1

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with Isolator

Global Fire Valkyrie ABI IP65 Addressable Red Beacon with IsolatorThe VALKYRIE ABI IP65 is a Wall Mounted Addressable Beacon with Isolator and low power consumption. It is specifically designed to be used outdoors. Up to 32 individually addressed beacons can be installed per loop occupying address 94 to 125. The address is set using switches 1 to 5 of the 8 way DIL switch.When individual address reporting is not required VALKYRIE ABI IP65 can be configured as a Shadow Beacon. In this case sounders do not occupy an address in the loop thus freeing up addresses for more detection devices. Shadow beacons do not report back to the control panel so their presence on the loop is not monitored.Shadow beacons draw current from the loop 3 mA in alarm and must be included in loop load calculations. These units are produced using the latest high intensity LED technology and use extremely low levels of current consumption providing a highly visible flash.

GBP 65.70

1

Global Fire MAM-WHITE Manually Addressed Module for Detector

Global Fire MAM-WHITE Manually Addressed Module for DetectorThe MAM allows the connection and addressing of Conventional Detectors Call Points Micro Input Micro Output and Conventional Sounder Beacon. With its small physical size and convenient 8 way DIL switch for address setting and configuration the MAM provides the facility to upgrade all the components of a conventional system to a full addressable system making it an ideal solution for retrofitting installations.The MAM is fully compatible with all our standard addressable modules addressable sounders addressable manual call points and GFE detectors facilitating extensions to existing systems.To assist easy identification the MAM is supplied in 3 coloured plastic housingsRed - Manual Call Point interface Micro Input ModuleYellow - Micro Output Module Loop Sounder Beacon ControllerWhite - Smoke Heat Detector interface.Device type selection is by means of switch 8 on the DIL. Additionally the MAM-LSC can be set as a sounder or beacon driver using switch 7. In Sounder mode the output is removed when a Silence Alarm signal is received from the control panel. In Beacon mode the output remains active until the system is reset.

GBP 23.52

1

Global Fire MAMRED Manually Addressed Module for Conventional Manual Call Points

Global Fire MAMRED Manually Addressed Module for Conventional Manual Call PointsThe MAM allows the connection and addressing of Conventional Detectors Call Points Micro Input Micro Output and Conventional Sounder Beacon. With its small physical size and convenient 8 way DIL switch for address setting and configuration the MAM provides the facility to upgrade all the components of a conventional system to a full addressable system making it an ideal solution for retrofitting installations.The MAM is fully compatible with all our standard addressable modules addressable sounders addressable manual call points and GFE detectors facilitating extensions to existing systems.To assist easy identification the MAM is supplied in 3 coloured plastic housingsRed - Manual Call Point interface Micro Input ModuleYellow - Micro Output Module Loop Sounder Beacon ControllerWhite - Smoke Heat Detector interface.Device type selection is by means of switch 8 on the DIL. Additionally the MAM-LSC can be set as a sounder or beacon driver using switch 7. In Sounder mode the output is removed when a Silence Alarm signal is received from the control panel. In Beacon mode the output remains active until the system is reset.

GBP 23.52

1

Global Fire Equipment OWL-6-OFFLINE OWL Graphical Software 6 Panels Offline

Global Fire Equipment OWL-6-OFFLINE OWL Graphical Software6 Panels OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during systemcommissioning devices icons may be placed on these drawings for easy alarmidentification. Therefore in an alarm condition the exact allocation of thealarm can be displayed in a graphical manner.The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 3434.39

1

Global Fire Equipment OWL-1-ONLINE OWL Graphical Software - 1 Panel Online

Global Fire Equipment OWL-1-ONLINE OWL Graphical Software -1 Panel OnlineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1303.57

1

Global Fire Equipment OWL-1-OFFLINE OWL Graphical Software - 1 Panel Offline

Global Fire Equipment OWL-1-OFFLINE OWL Graphical Software - 1 Panel OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1479.05

1

Global Fire Equipment OWL-2-5-ONLINE OWL Graphical Software - 2 -5 Panels Online

Global Fire Equipment OWL-2-5-ONLINE OWL Graphical Software - 2 -5 Panels OnlineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 1955.34

1

Global Fire Equipment OWL-2-5-OFFLINE OWL Graphical Software - 2 -5 Panels Offline

Global Fire Equipment OWL-2-5-OFFLINE OWL Graphical Software - 2 -5 Panels OfflineOwl is an advanced software program designed for monitoringand control of up to 64 Fire Alarm systems. A system can consist of a singlepanel or a multi panel network. Map drawings may be uploaded during system commissioningdevices icons may be placed on these drawings for easy alarm identification.Therefore in an alarm condition the exact allocation of the alarm can bedisplayed in a graphical manner. The biggest advantage of OWL software is the possibility todirectly import the panels Cause and Effect file Octo Gekko or G-Onemaking commissioning faster and seamless. Another advantage is the userfriendly and intuitive commissioning the software mapping and deviceallocation configuration is as simple as 1 2 3 click drag and drop.Key FeaturesUp to 64 systems can be connected up to 16000 connecteddevicesMaximum number of simultaneously connected PC users 5Supports Image format bmp jpeg etcSimple synchronization of panel configuration and graphicsdatabase2 groups of user levels admin and operatorSite survey option for Maintenance commissioningSelectable event notifications via Email and SMSDrag and drop icon placement provides easy device locationmappingGlobal event log with filter optionsSelectable event notifications via Email and SMSUser friendly backup restore facility100 control of the system

GBP 2130.83

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)