mcb.dk | Få success online

Fireclass 577.001.038FC 602SBD Conventional 2 Wire Sounder Base

Fireclass 577.001.038FC 602SBD Conventional 2 Wire Sounder BaseThe 602SBD Conventuonal 2 Wire Sounder Base provides an additional sounder function on the detection circuit. The Sounder Base should be used with an associated detector. Removal of the detector should not prevent the sounder operating but will flag up a fault at the control panel.It provides eight tone and variable volume settings. This detector base is a two-wire line powered option.Key FeaturesManufactured to EN54 part 3Integral sounder and detector baseVolume and tone adjustable after installationLow Power SynchronisationDo not require use of a standard baseEight tones and variable volume settingsProvides an additional sounder function

GBP 67.82

1

Fireclass 577.001.036FC 602SB Conventional 2 Wire Sounder Base

Fireclass 577.001.036FC 602SB Conventional 2 Wire Sounder BaseThe 602SB Conventional Sounder Bases provide an additional sounder function on collective fire detection circuits. They operate independently of the detector circuit and may be used without an associated detector.The 602SB Sounder Base may be used with or without an associated detector. When used with an associated detector removal of any detector or loss of power to the detection circuit may cause the sounder to cease operating. When used without an associated detector the wiring should be as shown in the alternate wiring scheme. It also provides eight tone and variable volume settings.This detector base is a two-wire line powered option.The 602SB provides the same tone specifications as the 601SB but is powered by a 2-wire detector loop. It is identified by a yellow park clip.Key FeaturesOperating Voltage LoopCircuitStandby Current 100A dumb mode 1.5mA intelligent modeAlarm Current 1.2mA 68dBA low vol 6.8mA 90dBA max volOperating Temp -25C to 70CRelative Humidity 10 to 95 non cond.Dimensions 108 dia x 38 mmWeight 195gWire Size 1.5mm2 to 2.5mm2

GBP 51.47

1

Fireclass OSID-WGFC Wire Guard for OSID Imager or Emitter

Fireclass OSID-WGFC Wire Guard for OSID Imager or EmitterThis steel cage is designed to protect OSID Imagers and Emitters from vandalism and accidental damage.The cage is constructed of heavy gauge steel wire with corrosion resistant polyester coating.Installation and servicing are easy.Highly recommended for areas where abuse to beams is severe.Key FeaturesDesigned to not interfere with the operation of the protected unitFast and easy installationSimple removal for servicing the unitsConstructed from 9-gauge galvanised steel rodPlastic coated for durability and use in harsh environmentsProtects against vandalism or accidental damage

GBP 46.19

1

Fireclass 540.001.039FC XB11 Flameproof Xenon Beacon

Fireclass 540.001.039FC XB11 Flameproof Xenon BeaconThese certified beacons have been designed for use in potentially explosive gas and dust atmospheres and harsh environmental conditions. The glass reinforced polyester enclosures are suitable for use offshore or onshore where light weight combined with corrosion resistance is required.The beacon housing is manufactured completely from a U.V. stable glass reinforced polyester. Stainless steel screws and mounting bracket are incorporated ensuring a totally corrosion free product.Key FeaturesRobust Corrosion Resistant GRP bodyDesigned for use in potentially explosive atmospheresSuitable for use offshore or onshore where a lightweight product combined with corrosion resistance is requiredManufactured from a U.V. stable glass reinforced polyesterThe strobes contain supervisory diode and four wire leads for fire alarm applicationsUnits can be painted to customer specification and supplied with identification labelsHigh Power 5 JouleCertificated FlameproofZones 1 2 21 and 22 useEx d IIB T4 T5T6ATEX approved Ex II 2GDUL certified for USA and Canada Hazardous locations Class I Div 2 Groups C D Class I Zone 1 2 AExd IIB T5 Ordinary locations visual-signal deviceIECEx certified Gb DbTR CU certifiedCQST certifiedINMETRO certifiedCertified temperature from 55C to 70CCorrosion resistant GRPOptional stainless steel backstrap

GBP 891.01

1

Fireclass 517.050.023FC 5BEX 5 Universal Ex Detector Base

Fireclass 517.050.023FC 5BEX 5 Universal Ex Detector BaseThe 517.050.023FC 5BEX detector base has been ATEX approved for use with the series M600Ex and series 800Ex intrinsically safe detectors and is covered by type examination certificates BAS01ATEX1134X3 and BAS01ATEX1194X3 respectively.The 5BEx 5 Universal Base is compatible with M600Ex MX 800Ex and the 800Exn ranges of Detectors. This document describes its use with the 800Exn series of detectors. Thus a ceiling-mounted detector comprises the specific detector type plus a 5BEx 5 Universal Base. The range is intended for two wire operation.When the detector is mounted on the base the detector LED provides a visual indication of its status through 360 degrees. The detector may be locked in position by inserting a locking key which is part of the detector moulding. This is broken from the sprue and inserted in the locking key slot.Key FeaturesHigh performanceDetector base is made of fire resistant FR110 BAYBLENDThe base can be used with the DHM-5BThe base accepts an address label carrier from the detector when it is fitted to the base. The base also has four electrical contacts which align with the contacts on the detector once the latter is fitted and fully latched into positionThe raised rib is aligned with a raised rib on the detector when the detector is in the fully home positionLoop cabling is connected to base terminals L -ve and L1 veA drive is provided for a remote indicator connected between loop positive and terminal RTerminal L2 is not used

GBP 14.99

1

Fireclass 516.016.027FC Digital Interface 2-Zone Monitor Module

Fireclass 516.016.027FC Digital Interface 2-Zone Monitor ModuleA Unique and Flexible dual zone Digital LHD Interface Monitor Module offering advanced functionality to traditional Digital LHD systems.A further important addition to Thermocables world leading family of digital linear heat detection technologies the ProReact Interface Monitor Module is designed to work with the ProReact Digital Linear Heat Detection Cable and effectively monitor up to two zones at any one time.The Digital Interface Monitor Module is unique in being approved to the UL864 10th edition standard the most recent revision to the UL standard for fire alarm control panels and accessories. It has been designed and tested against the stringent requirements of the 10th edition including new tests to confirm the integrity of the software in the device. The Digital Interface Monitor Module simultaneously monitors two zones of Digital LHD cable for an alarm or fault condition. If an overheat or fire situation triggers either zone of the Digital LHD cable the Module automatically calculates and displays the distance along the cable in feet and metres to the alarm point. The two zones can operate independently of each other or in interlockcoincidence detection mode to eliminate the possibility of false alarms.The Module is intended to be installed between the Digital Linear Heat Detection cable and a conventional or addressable fire alarm control panel. An RS-485 Modbus RTU output also allows direct connection into a PLC or other process control system.Typical ApplicationsPower generation industriesOil and gas industriesMinesCold storage and industrial freezersFloating roof storage tanksTunnelsCable traysWarehousingKey FeaturesAdvanced functionality for traditional Digital LHD systemsPinpoints exact location of an incident and responds immediatelySimultaneous monitoring of up to two zonesPower indicator fault and alarm lights for each zoneVolt-free outputs for fault and alarm corresponding to each zoneCan be connected to an industrial process control system using the two-wire RS485 Modbus RTU outputBuilt-in sounder for audible annunciationInterlockCoincidence detection eliminates the possibility of false alarms by requiring both LHD cables to trigger before transmitting an alarmUL CE RoHS approved to meet end user specificationsSimultaneous monitoring of up-to two zones increases potential applications. For example pre-alarm on one zonealarm on the other fault-tolerant triggering of alarm both zones must activate before alarm at panelImmediately pinpoints exact location and responds to an incidentCompatible with Thermocables ProReact Digital LHD cableCan be retro-fitted to existing installationsCost effectively increases functionality and performanceConnects to addressable fire alarm control panels for fast response to faultsLow installation and maintenance costs reduce total cost of ownershipReliability through design approvals and 3 year warranty

GBP 515.16

1

Fireclass FC501-HK Triple Circuit Single Loop Panel with Icons and 2.5A PSU

Fireclass FC501-HK Triple Circuit Single Loop Panel with Icons and 2.5A PSUFC501 is the newest FireClass addressable solution for small systems brought to you by Tyco Fire Protection Products. Conceived to be extremely easy to install and use the FC501 is an out of the box panel which offers the simplicity of a conventional system and the benefits of the FireClass addressable digital technology.Auto Addressing Intelli-Zone On line Help function USB interface to upload the configuration and the easiness to configure the panel via integrated keypad are only some of the features that allow the installation and configuration of the FC501 in just a few simple steps.This 3 in 1 loop panel enables 3 circuits of devices to be connected to this single loop panel providing greater flexibility and simplifying the wiring process. Once the loop devices are wired the system can be auto addressed by a single click. The devices are automatically assigned to 3 zones according to the physical loop they are connected to the system is ready to protect the site. If the system configuration needs to be modified and the devices re-addressed or the zonesre-programmed the powerful Intelli-Zone feature significantly reduces the configuration time allowing the installer to perform test and programming at once. The configuration software is extraordinarily user friendly and provides a very nice graphic interface that displays all devices connected to the different zones. A battery and wire calculation tool is included in the software to help the installer in sizing up the system.A free graphic maps software based on a multilevel maps tree structure allows a remote real time visualization of any loop zone and point status and the simple remote user interface with control buttons reset silence evacuate allow users to manage the system from any location in the world. The FireClass FC501 control panel supports a total of 128 devices including the double and triple technology detectors and a plenty of modules and sounders benefiting of one of the widest ranges available in the market.Key Features3 in 1 LoopsUp to 400mA current dynamically shared across 3 loop circuitsTwo versions available 1.5 A or 2.5 A power supplyUp to 128 Addresses 32 ZonesEasy to programmeAuto AddressingAuto mapping with Intelli-Zone featureOut of the BoxOn Line Help functionUSB interface dual role HostDeviceMulti UsersMulti Installers Up to 2 Installers 8 UsersWalk test function4000 Event LogLoop break locationOn board PSTN communicatorOptional IP boardGSMGPRS as external moduleLCD display 160 CharactersUp to 4 repeatersUp to 4 Multifunction interfaces for printer simplified fire brigade panelsEvent transmission via PSTN and IPFront panel controls enabling text and configuration changesDisplays temperature CO level and smoke level at any pointAutomatic drift compensation

GBP 531.17

1

Fireclass FC501-L Triple Circuit Single Loop Panel with 1.5A PSU

Fireclass FC501-L Triple Circuit Single Loop Panel with 1.5A PSUFC501 is the newest FireClass addressable solution for small systems brought to you by Tyco Fire Protection Products. Conceived to be extremely easy to install and use the FC501 is an out of the box panel which offers the simplicity of a conventional system and the benefits of the FireClass addressable digital technology.Auto Addressing Intelli-Zone On line Help function USB interface to upload the configuration and the easiness to configure the panel via integrated keypad are only some of the features that allow the installation and configuration of the FC501 in just a few simple steps.This 3 in 1 loop panel enables 3 circuits of devices to be connected to this single loop panel providing greater flexibility and simplifying the wiring process. Once the loop devices are wired the system can be auto addressed by a single click. The devices are automatically assigned to 3 zones according to the physical loop they are connected to the system is ready to protect the site. If the system configuration needs to be modified and the devices re-addressed or the zonesre-programmed the powerful Intelli-Zone feature significantly reduces the configuration time allowing the installer to perform test and programming at once. The configuration software is extraordinarily user friendly and provides a very nice graphic interface that displays all devices connected to the different zones. A battery and wire calculation tool is included in the software to help the installer in sizing up the system.A free graphic maps software based on a multilevel maps tree structure allows a remote real time visualization of any loop zone and point status and the simple remote user interface with control buttons reset silence evacuate allow users to manage the system from any location in the world. The FireClass FC501 control panel supports a total of 128 devices including the double and triple technology detectors and a plenty of modules and sounders benefiting of one of the widest ranges available in the market.Key Features3 in 1 LoopsUp to 400mA current dynamically shared across 3 loop circuitsTwo versions available 1.5 A or 2.5 A power supplyUp to 128 Addresses 32 ZonesEasy to programmeAuto AddressingAuto mapping with Intelli-Zone featureOut of the BoxOn Line Help functionUSB interface dual role HostDeviceMulti UsersMulti Installers Up to 2 Installers 8 UsersWalk test function4000 Event LogLoop break locationOn board PSTN communicatorOptional IP boardGSMGPRS as external moduleLCD display 160 CharactersUp to 4 repeatersUp to 4 Multifunction interfaces for printer simplified fire brigade panelsEvent transmission via PSTN and IPFront panel controls enabling text and configuration changesDisplays temperature CO level and smoke level at any pointAutomatic drift compensation

GBP 479.87

1

Fireclass FC501-H Triple Circuit Single Loop Panel with 2.5A PSU

Fireclass FC501-H Triple Circuit Single Loop Panel with 2.5A PSUFC501 is the newest FireClass addressable solution for small systems brought to you by Tyco Fire Protection Products. Conceived to be extremely easy to install and use the FC501 is an out of the box panel which offers the simplicity of a conventional system and the benefits of the FireClass addressable digital technology.Auto Addressing Intelli-Zone On line Help function USB interface to upload the configuration and the easiness to configure the panel via integrated keypad are only some of the features that allow the installation and configuration of the FC501 in just a few simple steps.This 3 in 1 loop panel enables 3 circuits of devices to be connected to this single loop panel providing greater flexibility and simplifying the wiring process. Once the loop devices are wired the system can be auto addressed by a single click. The devices are automatically assigned to 3 zones according to the physical loop they are connected to the system is ready to protect the site. If the system configuration needs to be modified and the devices re-addressed or the zonesre-programmed the powerful Intelli-Zone feature significantly reduces the configuration time allowing the installer to perform test and programming at once. The configuration software is extraordinarily user friendly and provides a very nice graphic interface that displays all devices connected to the different zones. A battery and wire calculation tool is included in the software to help the installer in sizing up the system.A free graphic maps software based on a multilevel maps tree structure allows a remote real time visualization of any loop zone and point status and the simple remote user interface with control buttons reset silence evacuate allow users to manage the system from any location in the world. The FireClass FC501 control panel supports a total of 128 devices including the double and triple technology detectors and a plenty of modules and sounders benefiting of one of the widest ranges available in the market.Key Features3 in 1 LoopsUp to 400mA current dynamically shared across 3 loop circuitsTwo versions available 1.5 A or 2.5 A power supplyUp to 128 Addresses 32 ZonesEasy to programmeAuto AddressingAuto mapping with Intelli-Zone featureOut of the BoxOn Line Help functionUSB interface dual role HostDeviceMulti UsersMulti Installers Up to 2 Installers 8 UsersWalk test function4000 Event LogLoop break locationOn board PSTN communicatorOptional IP boardGSMGPRS as external moduleLCD display 160 CharactersUp to 4 repeatersUp to 4 Multifunction interfaces for printer simplified fire brigade panelsEvent transmission via PSTN and IPFront panel controls enabling text and configuration changesDisplays temperature CO level and smoke level at any pointAutomatic drift compensation

GBP 501.42

1

Fireclass FC503 3 Loop Panel 250 Points

Fireclass FC503 3 Loop Panel 250 PointsThe FC503 is the newest FireClass addressable solution for a wide range of applications and requirements. Conceived to be extremely easy to install and use the FC503 is an out of the box panel which offers the simplicity of a conventional system and the benefits of the FireClass addressable digital technology. Auto Addressing Intelli-Zone Online Help function USB interface to upload the configuration and the easiness to configure the panel via integrated keypad are only some of the features that allow the installation and configuration of the panels in just a few simple steps.The FC503 panel has 3 in 1 loops that can support up to 250 addressable devices and 32 zones. The split loop technology enables 3 circuits of devices to be connected to one single loop providing greater flexibility andsimplifying the wiring process. Once the loop devices are wired the system can be auto addressed by a single click. The devices are automatically assigned to 32 zones according to the physical loop they are connected to the system is ready to protect the site. If the system configuration needs to be modified and the devices re-addressed or the zones re-programmed the powerful Intelli-Zone feature significantly reduces the configuration time allowing the installer to perform test and programming at once. The configuration software is extremely user friendly and provides a very nice graphic interface that displays all devices connected to the different zones.A battery and wire calculation tool is included in the software to help the installer in sizing up the system. A free graphic maps software based on a multilevel maps tree structure allows a remote real time visualization of any loop zone and point statusand the simple remote user interface with control buttons reset silence evacuate allow users to manage the system from any location in the world. This new FireClass FC503 control panel supports up to 250 devices including the double and triple technology detectors and a plenty of modules and sounders benefiting of one of the widest ranges available in the market.Key Features3 in 1 loopsUp to 800mA current dynamically shared across 3 loop circuitsAuto mapping with Intelli-Zone featureOnline Help functionUSB interface dual role HostDeviceMulti users and multi installers Up to 2 installers 8 usersWalk test function4000 Event LogLoop break locationOn board PSTN communicatorGSMGPRS as external moduleUp to 8 repeaters and up to 7 FC500 Series panel clientsEvent transmission through PSTN and IPAutomatic drift compensationFast and simple system configuration also offlineTransferable user databaseDevice graphic displayedBattery and wiring calculationCustomizable cables databaseVisualization of all the devices assigned to a single zoneRemote real time visualization of control panel loop and zone status and so on.Easy remote user interface with control buttons reset silence evacuateMultilevel map based on a tree structureAccess device data from any pages of the mapConfiguration downloadable to USB memory stickCapability to print zone label sheet for front panel customization

GBP 722.82

1

Fireclass FC506 6 Loop Panel 500 Points

Fireclass FC506 6 Loop Panel 500 PointsThe FC506is the newest FireClass addressable solution for a wide range of applications and requirements. Conceived to be extremely easy to install and use the FC506is an out of the box panel which offers thesimplicity of a conventional system and the benefits of the FireClass addressable digital technology. Auto Addressing Intelli-Zone Online Help function USB interface to upload the configuration and the easiness to configure the panel via integrated keypad are only some of the features that allow the installation and configuration of the panels in just a few simple steps.The FC506 auto-addressing panel has 6 in 2 loops that can support up to 500 addressable devices and 32 zones. The split loop technology enables 3 circuits of devices to be connected to one single loop providing greater flexibility andsimplifying the wiring process. Once the loop devices are wired the system can be auto addressed by a single click. The devices are automatically assigned to 32 zones according to the physical loop they are connected to the system is ready to protect the site. If the system configuration needs to be modified and the devices re-addressed or the zones re-programmed the powerful Intelli-Zone feature significantly reduces the configuration time allowing the installer to perform test and programming at once. The configuration software is extremely user friendly and provides a very nice graphic interface that displays all devices connected to the different zones.A battery and wire calculation tool is included in the software to help the installer in sizing up the system. A free graphic maps software based on a multilevel maps tree structure allows a remote real time visualization of any loop zone and point statusand the simple remote user interface with control buttons reset silence evacuate allow users to manage the system from any location in the world. This new FireClass FC506control panel supports up to 500 devices including the double and triple technology detectors and a plenty of modules and sounders benefiting of one of the widest ranges available in the market.Key Features 6 in 2 loopsUp to 800mA current dynamically shared across 3 loop circuitsAuto mapping with Intelli-Zone featureOnline Help functionUSB interface dual role HostDeviceMulti users and multi installers Up to 2 installers 8 usersWalk test function4000 Event LogLoop break locationOn board PSTN communicatorGSMGPRS as external moduleUp to 8 repeaters and up to 7 FC500 Series panel clientsEvent transmission through PSTN and IPAutomatic drift compensationFast and simple system configuration also offlineTransferable user databaseDevice graphic displayedBattery and wiring calculationCustomizable cables databaseVisualization of all the devices assigned to a single zoneRemote real time visualization of control panel loop and zone status and so on.Easy remote user interface with control buttons reset silence evacuateMultilevel map based on a tree structureAccess device data from any pages of the mapConfiguration downloadable to USB memory stickCapability to print zone label sheet for front panel customization

GBP 1073.92

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)