21 results (0,17931 seconds)

Show all filters

Brand

Colour

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Fast Mover Tools Displaced Parts Storage Trolley

Fast Mover Tools Displaced Parts Storage Trolley

A super useful displaced parts cart for any size of workshop. Comes complete with two mesh side frames with hooks and straps to attach vehicle panels to and a wire basket for those small items. There is an adjustable wire shelf for bulkier items. At the bottom of the trolley there is an area for the larger and heavier items Height: 1700mm Length: 890mm Width: 590mm Safe Working Load (SWL) 228KG 4 x 100mm Swivel Casters Light Grey RAL 7045

GBP 439.99
1

Fast Mover Tools Powered Air Breathing Mask, A2P3

Fast Mover Tools Powered Air Breathing Mask, A2P3

Powered Air Breathing Mask, A2P3. An air powered air-purifying respirator suitable for use in open and closed areas to protect the respiratory system, face, eyes and head. Recommended for pesticides spraying in the open and in the greenhouses, for grain handling, cleaning and disinfecting stables and pens, and during any work where it is necessary to effectively protect the respiratory system, eyes and head. These respirators work by means of a slight overpressure created by a flow of filtered air. The air, sucked and purified through the filters by means of a control unit, is sent through the tube inside the helmet. Control unit, filters and battery are worn on the belt. The electric respirator with helmet is a device capable of providing combined protection of the head (EN397) , face and eyes (EN166) and respiratory tract from gases and particles (EN12941) The adjustable internal harness locks the helmet to the forehead giving greater visibility to the operator. The polyamide collar allows a pleasant and efficient closure of the helmet around the operators neck. The respirator is designed to be used both in compact mode and in mode with control unit and battery on the belt. This is possible by changing the rear insert. The e-T5 control unit is equipped with a silent and long-lasting coreless motor and a monitoring system for the state of charge of the battery and the minimum flow by means of a LED and a buzzer. The lightness of the device allows it to be used without the use of a shoulder support. FEATURES AND BENEFITS PROTECTION: The electro respirator with helmet is the only assisted ventilation device capable of providing combined protection for the head, face and eyes, andrespiratory tract from particles and gas.The aspirated and filtered air is introduced into the helmet via the control unit and connection pipe, creating a slight over pressure.The continuous and uniform flow of air prevents fogging of the visor and eliminates any respiratory effort, offering protection and comfort for the operator. COMFORT: The respirator is easy to don and use also by inexperienced workers. Lightweight and of simple design, it is comfortable to wear even in harsh working conditions. LIFE: The use of carefully selected first choice raw materials guarantee a product average life expectancy of over ten years. FLOW INDICATOR: there are 2 flow indicators: a visual and acoustic one on the ventilation unit and a sphere flow indicator always visible on the visor. These systems allow to keep under control the functioning of the respirator. LITHIUM BATTERIES: The latest generation lithium battery, lightweight and of easy maintenance, is carried at the waist. VENTILATION UNIT: Equipped with a silent and long-lasting coreless motor and a system that allows the monitoring of the minimum flow and the state of charge of the battery. HELMET: The inner headband, adjustable from 52 to 63 cm, blocks the helmet round the forehead allowing for excellent visibility when the worker turns his head. Ultraviolet sun rays are repelled by the white color of the helmet.The helmet complies with the requirements of the EN 397 standard: protects the head from falling objects and brain injuries to the skull that may result. COLLARS: The polyamide collar closes efficiently and comfortably around the workers neck. VISOR: It complies with the requirements of the EN166 standard: it is in optical class 2 and resists particles with a speed of 120 m/s. Allows visibility over 90%. Anti-fog and anti-scratch treatments have been carried out on the visor. Protective films, to be fixed to the special pins, can be supplied as an accessory to further protect the visor. There is a minimum flow indicator on the visor. STANDARD COMPONENTS: a helmet with a visor that can be closed using a special hook and integrated range indicator, a type C insert that allows the connection of a breathing tube to the helmet, a ventilation unit with integrated electronics, a lithium battery, a battery charger, an A2P3 filter, a belt, a breathing tube, an electric cable. TECHNICAL INFORMATION CLASSIFICATION EN 12941:98+A1:03+A2:08: TH3 A1P R SLCONFORMITY REGULATION EU 2016/425NOMINAL PROTECTION FACTOR (NPF) EN529:2006: 500OPTICAL CLASS: IICOMPLIANCE WITH THE REQUIREMENTS OF EN166: 2001 AND EN397: 2012 + A1: 2012MAX AIRFLOW AT 20C-60%RH*: 160 l/minMIN AIRFLOW AT 20C-60%RH: 120 l/minCOMPLETE RESPIRATOR/HELMET WEIGHT: 3 kg/1 kgSOUND LEVEL: 68 dBaPOWER: 7, 4 VBATTERY TYPE: Li-IonRECHARGING TIME: 3 hRUNNING TIME: >8 hAVAILABLE SIZES Adjustable headbandINGRESS PROTECTION RATING IP**: 65 *with battery fully charged and new filters**Air system: blower unit, breathing tube, electric cord, filters

GBP 799.99
1

Fast Mover Tools Air Operated Surface Conditioning Tool Kit

Fast Mover Tools Air Operated Surface Conditioning Tool Kit

A fantastic air operated surface preparation tool. This tool will efficiently and effectively remove paint, undercoating seam sealer and rust without damaging or taking away the metal. The tool is ergonomically designed and can access all those difficult to get at areas - under the wheel arches, between the panels, grooves and tight corners. Use the eraser wheels to remove stickers, sign writing adhesive, tape, glue from painted metal, plastic or wood surfaces. Kit includes 1 x FT1047 Air surface Conditioning Tool 3 X FMT5085 Wire Brush 3 X FMT5019 Conditioning Wheel 3 X FMT5011 Fluted Rubber Eraser Wheel 100mm 1 X FMT5020 Hub Assembly

GBP 439.99
1

Fast Mover Tools Pneumatic Soft Foil Cartridge Dispensing Gun

Fast Mover Tools Pneumatic Soft Foil Cartridge Dispensing Gun

Pneumatic Sausage Cartridge Dispensing Gun. The cartridge or soft pack is held within a metal casing therefore making it easier to achieve the desired effect. A very well-balanced dispensing gun with a comfortable and ergonomic handle. The gun is equipped with a telescopic piston that prevents the compressed air coming into contact with the material sprayed. Fitted with an air regulator to control air flow and a regulator to control the flow of the sealant Supplied with a variety of nozzles to achieve different effects

GBP 659.99
1

Fast Mover Tools 3 Stage Turbine Sprayer with Gun & Hose

Fast Mover Tools 3 Stage Turbine Sprayer with Gun & Hose

3 Stage Turbine Sprayer With Gun & Hose. The FMT7830 Turbine sprayer is a powerful and efficient turbine delivering High Volume air at Low Pressure. Its this massive air volume that atomises the paint not the pressure, so the paint stays on the surface and does not bounce back onto surrounding areas nor into the atmosphere. Easy to spray cleanly, efficiently and achieve a fantastic finish with minimal masking off. And because bounce back is reduced you will save paint and help protect the environment too. FMT7830 Turbine sprayer is perfect where space is limited and for on-site spraying, classic cars, shop fitting, decorating, custom kitchen fitters and bath re-enamellers anywhere needing clean, hassle-free spray with a great finish. Specification Fitted with Non-bleed spray gun Supplied with 6mtr hose Size 260mm x 310mm x 250mm Lightweight at just 15Kg Suitable for water based paints 3 stage motor 1500watt 240v Replacement gun FMT7890 Replacement hose Quiet running motor 240v or 110v available - please enquire Simple to use and maintain.

GBP 799.99
1

Fast Mover Tools Skipper Airless Paint Sprayer Kit, 240 Volt

Fast Mover Tools Skipper Airless Paint Sprayer Kit, 240 Volt

Skipper Airless Paint Sprayer Kit, 240 Volt. Our popular airless paint sprayer the Skipper is a complete kit with a 15mtr hose and airless gun and is suitable for spraying all types of paints onto all types of surfaces with the minimum amount of overspray. Designed to spray and get the job perfectly done every time! The Skipper is a compact, lightweight, portable, yet powerful sprayer and is perfect for working in the yard spraying plant, machinery, boats, large fences, steel beams, warehouse cladding, in the factory spraying furniture and finished steel fabricated items and in and around the construction site spraying walls, both internally and externally. Airless paint sprayers enable the user to apply coatings quickly over large areas with perfect and consistent finishing. They can be used in a wide variety of industries and are ideal for those that want to finish the job fast , efficiently and on time! Our Skipper is one of the market leaders in their field due to its robust piston pump manufactured in Europe and durable gun and hose, and with a high level of efficiency. The Skipper is an easy to use and maintain paint sprayer and is ready to plug in and spray. Suitable for spraying water or solvent based paints, primers, fillers, acrylic paints, latex, emulsions, epoxy resins, lacquers, wood paints, insulation coatings, bitumens and adhesives. In short this Skipper is the economical answer to any paint spraying requirements and is a must for any property maintenance team, plant hire yard, decorator and factory owner. Specification Voltage 110 Volt Motor power 0.7 Kw Power supply 4 KW single Phase Max working pressure 220 Bar Max delivery 1.9 L/Min Pump Weight 15Kg Max nozzle size 0, 021 Fluid outlet 1/4 NPT-NPSM Sound pressure level 80 dB (A) Fluid filter 60 Mesh All spare parts available and replacement guns are FMT4710, FMT4720 and FMT4765. Replacement hoses FMT71405 5Mtrs FMT71410 10Mtrs FMT71415 15Mtrs

GBP 2099.99
1

Fast Mover Tools Thermostat, Atex Approved - for Use with FAW1000

Fast Mover Tools Thermostat, Atex Approved - for Use with FAW1000

An ATEX approved cast aluminium alloy thermostat for use with the FAW1000 Paintroom and hazardous area air warmers. This ATEX approved thermostat is suitable for installation in Zone 1 or 2 hazardous areas. The AFT40 has external adjustment enabling quick and accurate variable control. Features 2 cable entries and external and internal earths. Wall mounted with threaded boss or industry standard flange. Suitable for use in ambient temperatures -60 to + 60 degrees C. 250V 16 Amp ATEX certified 11 2G/D IECEx & ATEX certified Ex`d` 11C T6 Ex tD A21 IP6X T85 degrees C for Zone 1 or 2 (GAS) and Zone 21 or 22 (DUST). Size 126mm x 113mm x 86mm

GBP 479.99
1

Fast Mover Tools Parts Storage Cart 3 Shelves 210Kg Capacity

Fast Mover Tools Parts Storage Cart 3 Shelves 210Kg Capacity

The best displaced parts trolley you will ever buy! Strong, robust, agile and very practical. Even fits through a standard pedestrian door! This makes it very easy to fit between parked cars and enabling them to go from one workshop to another.The bottom mesh shelf is great for heavy or dirty items, and the 2 further wooden shelves will carry the cleaner or larger items. Light Grey RAL 7045. Heavy Duty 4 x 100mm casters. Safe Working Load (SWL) 210kg

GBP 799.99
1

Fast Mover Tools Wheel Skates, Pair, 1800kg Capacity per Pair

Fast Mover Tools Wheel Skates, Pair, 1800kg Capacity per Pair

Please note the wheels are now Green and not White Simply jack up the vehicle and slide the skate under the wheel and lower the wheel into the skate. The 4 swivel casters will enable the vehicle to be kept mobile. With 2 pairs ( one skate under each wheel) the whole vehicle can be moved or rotated in any direction. Designed for use on relatively smooth surfaces, will take rough concrete but don't like potholes! We suggest the wheel is strapped to the skate using a ratchet strap. 1800kg capacity per pair

GBP 599.99
1

Fast Mover Tools Paint Room Heater Atex Approved 240v 1KW

Fast Mover Tools Paint Room Heater Atex Approved 240v 1KW

FAW1000 offers a versatile, lightweight air warming solution for small work and storage areas. With the extremely high cost of paint stored in the average bodyshop, it is extremely critical that it is properly stored at the correct temperature. Suitable for use in Zone 1 and 2 T2/T3 Class Our air warmer is fully ATEX approved, a thermostat is available to purchase separatley (AFT40) and is not supplied with the heater shown. Typical Applications: Aircraft Hangers. Offshore Installations. Fuel Servicing Areas. Battery Stores. Chemical Plants. Container Heating Spray Booths Motor Enclosures Gas Installations Fuel Servicing Areas To name a few.. Powder Coated Finish. 1000kw. Certified to meet the ATEX directive 94/9/EC. Weatherproof to IP66/67. Floor mounted. Suitable for ambient temperatures between -60C and +60C. Individually replaceable heater elements. L: 1221mm D: 160mm H: 186mm Weight: 14 Kg

GBP 1299.99
1

Fast Mover Tools Infrared Paint Dryer, Mobile, 3KW Single Phase 240V

Fast Mover Tools Infrared Paint Dryer, Mobile, 3KW Single Phase 240V

Mobile 3KW 240V Infrared Paint Dryer with Timer Allow 5 working days for delivery Our FMT6930 Mobile 3KW infrared paint dryer will greatly increase your efficiency and reduce drying times all with a low cost and sustainable energy. This paint dryer emits short wave infrared heat which is ideal for optimising drying of water-based paints and can typically reduce drying times from 45mins to 10 mins! Improving efficiencies is what its all about and you will achieve a rapid return on investment by increasing your throughput and faster turn around times in your Paintshop. The cassettes are set out to give you the maximum drying area and at 500mm will give you a drying area of 800 x 1000mm. A fully flexible stand will allow you to cover the low-down areas of any vehicle as well as high sided vans and on top of the roofs. The bulbs are considered low glare therefore not causing an issue for the operative and nearby workers. The swivel casters are designed to roll easily over spray booth grids and grating. Locking rear swivel casters Locking gas strut to fix arm height. 099-minute timer with the ability to have 1, 2 or all three cassettes in use. With proper care the bulbs will provide approximately 20, 000hrs of use. Specification Single phase 240V Current 12.5 (A) 13 AMP fused 3 pin plug Replacement bulbs FMT64241034 Both flash and bake settings. Temperature settable on both flash and bake cycle. 3 pre-set memory functions. Temperature display of time and setting of both flash and bake cycles. Standard controls +Distance/temperature sensors Temperature settable on both flash and bake cycle. Optical electronic digital feedback loop adjusts heat automatically during cycle. Digital distance readout with safety cut out if unit is moved too close.

GBP 1119.99
1

Fast Mover Tools Heavy Duty Wheel Skates, 3600KG Capacity per Pair

Fast Mover Tools Heavy Duty Wheel Skates, 3600KG Capacity per Pair

Please note the wheels are now Green and not White The strongest wheel skate money can buy! A massive 1800kg load capacity per skate means these skates will handle the largest and heaviest of vehicles including loaded vans and small trucks. These skates are designed for heavy use in the recovery industry and are virtually indestructible. Simply jack the damaged vehicle up and lower the wheel (damaged or flat tyres no problem) into the skate, the vehicle is then mobile. When using two pairs, the vehicle can be moved or rotated in any direction. Stop wasting time and effort dragging disabled vehicles around the workshop! Can be used for winching vehicles up onto recovery truck slide beds. Dimensions of skate frame Length 666mm Width 435mm Castors 125mm white nylon swivel FMT331 Max Type Width: 400mm SWL 3600kg per Pair Weight: 22.5kg per Unit We suggest the wheel is strapped to the skate using a ratchet strap.

GBP 899.99
1

Fast Mover Tools Mobile Alloy Wheel Painting StanD, Holds 4 Wheels

Fast Mover Tools Mobile Alloy Wheel Painting StanD, Holds 4 Wheels

Mobile Alloy Wheel Painting Stand Holds 4 Wheels with Tyres A strong and robust alloy wheel painting stand. This stand will take four alloy wheels and enable the painter to rotate the without touching them so they can be painted completely without the need to lift and reposition the wheel. The supporting bars can be adjusted in height and the cones can be adjusted as well so the painter can work at the most comfortable position. The trolley can be moved around the workshop with the wheels mounted so saving further time and at the end of the job it can be dismantled in next to no time and stored away, absolutely great for mobile smart repairers. Size of base 1000mm x 750mm Size of support arms 1200mm

GBP 459.99
1

Fast Mover Tools TH3 PAPR (NPF=500) Powered Air-purifying Respirator

Fast Mover Tools TH3 PAPR (NPF=500) Powered Air-purifying Respirator

TH3 PAPR (NPF=500) Powered air-purifying respirator Recommended for protection against particles and during any work where it is necessary to effectively protect the respiratory system, eyes, and head. The KAIO series respirators work by means of a slight overpressure created by a flow of filtered air. The air, sucked and purified through the filters by means of a control unit, is sent inside the helmet. Control unit, filter and battery are integrated into the helmet. The electric respirator with helmet is a device capable of providing combined protection of the head (EN397) , face and eyes (EN166) and respiratory tract from particles (EN12941) The adjustable internal harness locks the helmet to the forehead giving greater visibility to the operator. The polyamide collar allows a pleasant and efficient closure of the helmet around the operators neck. The respirator is designed to be used both in compact mode and in mode with control unit and battery on the belt. This is possible by changing the rear insert. The e-TA control unit is equipped with a silent and long-lasting brushless motor and a monitoring system for the state of charge of the battery and the minimum flow by means of a LED and a buzzer. The lightness of the device allows it to be used without the use of a shoulder support. FEATURES AND BENEFITS PROTECTION: The electro respirator with helmet is the only assisted ventilation device capable of providing combined protection for the head, face and eyes, andrespiratory tract from particles.The aspirated and filtered air is introduced into the helmet via the integrated control unit, creating a slight over pressure.The continuous and uniform flow of air prevents fogging of the visor and eliminates any respiratory effort, offering protection and comfort for the operator. COMFORT: The respirator is easy to don and use also by inexperienced workers. Lightweight and of simple design, it is comfortable to wear even in harsh working conditions. LIFE: The use of carefully selected first choice raw materials guarantee a product average life expectancy of over ten years. FLOW INDICATOR: there are 2 flow indicators: a visual and acoustic one on the ventilation unit and a sphere flow indicator always visible on the visor. These systems allow to keep under control the functioning of the respirator. LITHIUM BATTERIES: The latest generation lithium battery, lightweight and of easy maintenance built into the helmet. VENTILATION UNIT: Equipped with a silent and long-lasting coreless motor and a system that allows the monitoring of the minimum flow and the state of charge of the battery. HELMET: The inner headband, adjustable from 52 to 63 cm, blocks the helmet round the forehead allowing for excellent visibility when the worker turns his head. Ultraviolet sun rays are repelled by the white colour of the helmet.The helmet complies with the requirements of the EN 397 standard: protects the head from falling objects and brain injuries to the skull that may result. COLLARS: The polyamide collar closes efficiently and comfortably around the workers neck. VISOR: It complies with the requirements of the EN166 standard: it is in optical class 2 and resists particles with a speed of 120 m/s. Allows visibility over 90%. Anti-fog and anti-scratch treatments have been carried out on the visor. Protective films, to be fixed to the special pins, can be supplied as an accessory to further protect the visor. There is a minimum flow indicator on the visor. STANDARD COMPONENTS: a helmet with a visor that can be closed using a special hook and integrated range indicator, a type A insert that integrates a ventilation unit and lithium battery inside, a battery charger, a P3 filter. TECHNICAL INFORMATION CLASSIFICATION EN 12941:98+A1:03+A2:08: TH3 P R SLCONFORMITY REGULATION EU 2016/425NOMINAL PROTECTION FACTOR (NPF) EN529:2006: 500OPTICAL CLASS: IICOMPLIANCE WITH THE REQUIREMENTS OF EN166: 2001 AND EN397: 2012 + A1: 2012MAX AIRFLOW AT 20C-60%RH*: 170 l/minMIN AIRFLOW AT 20C-60%RH: 120 l/minCOMPLETE RESPIRATOR/HELMET WEIGHT: 1, 49 kgSOUND LEVEL: 74 dBaPOWER: 7, 4 VBATTERY TYPE: Li-IonRECHARGING TIME: 3 hRUNNING TIME: >8 hAVAILABLE SIZES Adjustable headband Not suitable for use with paints containing isocyanates *With battery fully charged and new filters Some of the intended uses for which the operators respiratory system protection device against solid and liquid aerosols (particle filter P3) has been designed: Local sanitation and cleaning Wood processing Building, Construction, Renovations Processing with glass and mineral fibres Metal processing Painting and surface treatment Biological risk Chemistry and Pharmaceuticals: Treatment with powders, chemical formulations and special pastes.

GBP 1199.99
1

Fast Mover Tools Paint Pressure Tank, 10ltr, Manual Agitator, CE Approved

Fast Mover Tools Paint Pressure Tank, 10ltr, Manual Agitator, CE Approved

10ltr paint pressure tank on 4 swivel casters and fitted with a manual agitator. CE Approved and built in a factory TUV regulated. This tank is ideal for painting large areas as the large tank will mean less refills. It is great for painting paint, glues, grease and a wide range of other coatings Use this pressure tank with the FMT6079 gun and the twin air and fluid hoses FMT8910. Fitted with an air regulator and gauge.

GBP 469.99
1

Fast Mover Tools 200Bar Air Assisted Airless Spray Gun Standard 411 Aircap

Fast Mover Tools 200Bar Air Assisted Airless Spray Gun Standard 411 Aircap

200Bar Air Assisted Airless Spray Gun standard. Our best selling manual air assisted airless spray gun. Suitable for spraying metal coatings and wood finishes. A great gun thats both efficient and easy to produce great results. Manufactured in Europe to a very high standard and can be used with any brand of pump. The gun is supplied with our standard air assisted air cap and spray tip, but other branded air caps can be used if required. Fitted with a 411-air cap, and all a range of different size tips available. Air assisted spraying gives you all the advantages of airless spraying, speed and coverage but giving you the fine finish expected from low pressure spraying. Maximum Working Fluid Pressure:200 bar, 20 MPa (2900 psi) Maximum Working Air Pressure 7 bar, 0, 7 MPa (100 psi) Maximum Working Fluid Temperature:43CFluid Inlet: 1/4" npsAir Inlet:1/4" npsGun Weight with filter holder:520 gramsGun Body:AluminiumTrigger Resistance:17.35 NWetted Parts:Stainless steel, carbide, PTFE

GBP 499.99
1

Fast Mover Tools Skipper Airless Paint Sprayer Kit Trolley Mounted 220v 1.9L/Min 220Bar

Fast Mover Tools Skipper Airless Paint Sprayer Kit Trolley Mounted 220v 1.9L/Min 220Bar

Our popular airless paint sprayer the Skipper is a complete kit with a 15mtr hose and airless gun and is suitable for spraying all types of paints onto all types of surfaces with the minimum amount of overspray. The Skipper is a compact, lightweight, portable, yet powerful sprayer and is perfect for working in the yard spraying plant, machinery, boats, large fences, steel beams, warehouse cladding, in the factory spraying furniture and finished steel fabricated items and in and around the construction site spraying walls, both internally and externally. Suitable for spraying water or solvent based paints, primers, fillers, acrylic paints, latex, emulsions, epoxy resins, lacquers, wood paints, insulation coatings, bitumens and adhesives. In short this Skipper is the economical answer to any paint spraying requirements and is a must for any property maintenance team, plant hire yard, decorator and factory owner.

GBP 2499.99
1