mcb.dk | Få success online

XPZ730 Dunlop Standard Raw Edge Belt

Moulded Cog or Raw-edge V-belts have higher capacity and efficiency and they use smaller pulleys than traditional envelope (wrapped) belts. These belts have a higher coefficient of friction and are more aggressive, which makes them a very efficient belt for power transmission Unlike conventional fabric-covered V-belts, raw-edge belts have no cover. Thus, the cross-sectional area normally occupied by the cover is used for more load-carrying cord. Cogs on the inner surface of the belt increase air flow to enhance cooler running. They also increase flexibility, allowing the belt to operate with smaller pulleys.

GBP 0.00

1

XPZ1400 Dunlop Standard Raw Edge Belt

Moulded Cog or Raw-edge V-belts have higher capacity and efficiency and they use smaller pulleys than traditional envelope (wrapped) belts. These belts have a higher coefficient of friction and are more aggressive, which makes them a very efficient belt for power transmission Unlike conventional fabric-covered V-belts, raw-edge belts have no cover. Thus, the cross-sectional area normally occupied by the cover is used for more load-carrying cord. Cogs on the inner surface of the belt increase air flow to enhance cooler running. They also increase flexibility, allowing the belt to operate with smaller pulleys.

GBP 4.99

1

20-L-100F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

19-L-100F Imperial Pilot Bore Timing Pulley, 19 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

27L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

24L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

22L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

23L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

26L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 0.00

1

Dunlop BTL 40-L-075F Imperial Taper Bore (1108) Timing Pulley, 18 Teeth, 3/8" Pitch, for A 1/2" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 21.99

1

Dunlop BTL 32-L-100F Imperial Pilot Bore Timing Pulley, 32 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 17.39

1

Dunlop BTL 18L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 5.19

1

Dunlop BTL 26-L-100F Imperial Pilot Bore Timing Pulley, 26 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 12.99

1

Dunlop BTL 25-L-100F Imperial Taper Bore (1108) Timing Pulley, 25 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 15.99

1

Dunlop BTL 30-L-100F Imperial Pilot Bore Timing Pulley, 30 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 15.99

1

Dunlop BTL 36L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 14.29

1

Dunlop BTL 32L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 10.99

1

Dunlop BTL 22-L-100F Imperial Pilot Bore Timing Pulley, 22 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 9.49

1

Dunlop BTL 25L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 7.99

1

Dunlop BTL 19L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 5.59

1

Dunlop BTL 18-L-100F Imperial Pilot Bore Timing Pulley, 18 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 12.99

1

Dunlop BTL 28-L-100F Imperial Pilot Bore Timing Pulley, 28 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 14.39

1

Dunlop BTL 40-L-100F Imperial Pilot Bore Timing Pulley, 40 Teeth, 3/8" Pitch, for A 1" Wide Belt

Imperial timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 25.99

1

Dunlop BTL 21L050F (1108) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 6.29

1

Dunlop BTL 40L050F (1610) Timing Belt Pulley Taper Bore

Dunlop timing pulleys have equally spaced grooves machined in to the outside diameter, to give correct meshing with the belts teeth, The pulley grooves are of special design to give this correct meshing of the belt teeth with minimal friction. All pulleys manufactured have correct minimum meshing tolerances built in and the pitch diameter is always larger then the outside diameter.

GBP 16.99

1

DIGITAL MARKETING

Brand

Size

Merchant

Price (EUR)

XPZ730 Dunlop Standard Raw Edge Belt

XPZ1400 Dunlop Standard Raw Edge Belt

20-L-100F Imperial Pilot Bore Timing Pulley, 20 Teeth, 3/8" Pitch, for A 1" Wide Belt

19-L-100F Imperial Pilot Bore Timing Pulley, 19 Teeth, 3/8" Pitch, for A 1" Wide Belt

27L050F (1108) Timing Belt Pulley Taper Bore

24L050F (1108) Timing Belt Pulley Taper Bore

22L050F (1108) Timing Belt Pulley Taper Bore

23L050F (1108) Timing Belt Pulley Taper Bore

26L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 40-L-075F Imperial Taper Bore (1108) Timing Pulley, 18 Teeth, 3/8" Pitch, for A 1/2" Wide Belt

Dunlop BTL 32-L-100F Imperial Pilot Bore Timing Pulley, 32 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 18L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 26-L-100F Imperial Pilot Bore Timing Pulley, 26 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 25-L-100F Imperial Taper Bore (1108) Timing Pulley, 25 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 30-L-100F Imperial Pilot Bore Timing Pulley, 30 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 36L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 32L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 22-L-100F Imperial Pilot Bore Timing Pulley, 22 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 25L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 19L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 18-L-100F Imperial Pilot Bore Timing Pulley, 18 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 28-L-100F Imperial Pilot Bore Timing Pulley, 28 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 40-L-100F Imperial Pilot Bore Timing Pulley, 40 Teeth, 3/8" Pitch, for A 1" Wide Belt

Dunlop BTL 21L050F (1108) Timing Belt Pulley Taper Bore

Dunlop BTL 40L050F (1610) Timing Belt Pulley Taper Bore

Powered by Cobiro