59 results (0,15679 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec RXTI2 Hearing Loop Listener

C-Tec RXTI2 Hearing Loop Listener

C-Tec RXTI2 Hearing Loop ListenerAllows installers and non-hearing aid users to quickly assess the quality and audibility of an induction loop system ideal for daily system checking. The unit also allows non-hearing aid users to listen to the amplified sound generated by hearing loops in theatres cinemas churches etc. bringing performances sermons and general conversation closer to their earsKey FeaturesOn board filters helps reduce mains hum and background noiseIdeal for surveillance museum talk-through and stage manager talk-back systemsRotary onoff and volume control cw soft start functionality3.5mm headphone socket Impedance of headphones not supplied should be no greater than 32 ohmRequires 2 x AAA batteries

GBP 72.67
1

C-Tec BF330CTSR 24V Loop Sounder - Shallow Base - Red

C-Tec BF330CTSR 24V Loop Sounder - Shallow Base - Red

C-Tec BF330CTSR 24V Loop Sounder - Shallow Base - RedThe C-Tec BF330CTSR is a wall-mounted addressable sounderwith isolator. It is designed for use with C-Tec XFP analogue addressable firealarm panels compatible with Apollo Discovery protocols.Key FeaturesIncludes a built-in short-circuit loop isolatorDIP switch addressableExcellent lateral sound distribution92dBA sound output 1m700 quiescent currents 5.5mA typical alarm current 24Vsounder at max. volume15 selectable industry-standard tone pairs and 7 volumelevels selectable at panelPanel programmable group addressing allows multiple soundersto operate simultaneouslyLocking system offers full compliance with BS5839 Part 12002 Clause 12.2.2IP43 rated shallow base has a wide access hole for cableentry IP65 rated deep base allows wiring access through back or sideDesigned to comply with EN54-3 2001Dimensions 94mm diameter x 83mm BF330CTSR 94mm diameterx 101mm BF330CTDR

GBP 45.53
1

C-Tec BF333CTDR 24V Loop Sounder VID Deep Base - Red

C-Tec BF333CTDR 24V Loop Sounder VID Deep Base - Red

C-Tec BF333CTDR 24V Loop Sounder VID Deep Base - RedThe C-Tec BF333CTDR is a wall-mounted addressable unit thatcombines a sounder and flashing beacon. It is designed for use with C-Tec XFPanalogue addressable fire alarm panels compatible with Apollo XP95 andDiscovery protocols.The BF333CTDR features a red body and lens and it includesa deep back box making it ideal for surface cabling installations.Key FeaturesIncludes a built-in short-circuit loop isolator4 DIP switch addressable4 Excellent lateral sound distribution4 92dBA sound output 1m4 700A quiescent current 8mA typical alarm current 24Vbeacon lit sounder max. volume4 15 selectable industry-standard tone pairs and 7 volumelevels selectable at panel4 Panel programmable group addressing allows multiplesounders to operate simultaneously4 Locking system offers full compliance with BS5839 Part 12002 Clause 12.2.24 Beacon and Sounder can be set to operate independently ofeach other4 IP43 rated shallow base has a wide access hole for cableentry IP65 rated deep baseallows wiring accessthrough back or side4 Designed to comply with EN54-3 2001 and EN54-23 20104 Dimensions 94mm diameter x 89mm BF333CTSR94mm diameter x 106mm BF333CTDR

GBP 47.43
1

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio Plate

C-Tec APL Line Level Audio PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.62
1

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level Plate

C-Tec APXL XLR 3 Pin Line Level PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts stereo phono line-level input signals from sources such as TVs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.64
1

C-Tec BF459ACXW CX O Class Base - VAD - White

C-Tec BF459ACXW CX O Class Base - VAD - White

C-Tec BF459ACXW CX O Class Base - VAD - WhiteThe Base Mount range of addressable loop-powered basesincludes voice sounders and combined voice sounder visual alarm devices VADs.Their purpose is to visually and audibly alert building occupants of a firealarm. They are designed for use with C-TECs ZFPXFP Apollo Discovery protocolpanels and other third-party Apollo Discovery protocol panels. Howevercompatibility testing with third-party panels is recommended to ensure correctoperation.The bases offer low current consumption highsound output high efficiency VADs seven selectable volume levels 15 selectabletone pairs and built-in short-circuit loop isolators.

GBP 50.47
1

C-Tec PL1SHELF Wall Mounting Storage Shelf for PL1 Amplifier

C-Tec PL1SHELF Wall Mounting Storage Shelf for PL1 Amplifier

C-Tec PL1SHELF Wall Mounting Storage Shelf for PL1 AmplifierAttractive easy-to-fit mounting accessory that safely and securely holds a PL1 portable loop amplifier when it is not in use. Includes a pre-cut hole for feeding through the plug-top power supplyslead to the PL1s charger socket so theamplifier can becharged whilst stored on the shelf.Key FeaturesBuilt-in pocket for instruction storage.Finished in black high-impact plastic.Technical SpecificationsApplication operation allows the PL1 portable hearing loop amplifier to be safely stored on a wallProduct dimensions W260 x H263 x D14 mmConstructions Black high impact plastic shelfWeight 360g

GBP 43.88
1

C-Tec BF457ACXWLD CX C Class Base Voice Sounder - White Lockdown

C-Tec BF457ACXWLD CX C Class Base Voice Sounder - White Lockdown

C-Tec BF457ACXWLD CX C Class Base Voice Sounder - White LockdownThe Base Mount range of addressable loop-powered basesincludes voice sounders and combined voice sounder visual alarm devices VADs.Their purpose is to visually and audibly alert building occupants of a firealarm. They are designed for use with C-TECs ZFPXFP Apollo Discovery protocolpanels and other third-party Apollo Discovery protocol panels. Howevercompatibility testing with third-party panels is recommended to ensure correctoperation.The bases offer low current consumption highsound output high efficiency VADs seven selectable volume levels 15 selectabletone pairs and built-in short-circuit loop isolators.Please note this image is for illustrative purposes only

GBP 64.69
1

C-Tec BF455ACXW CX O Class Base Voice Sounder - VAD - White

C-Tec BF455ACXW CX O Class Base Voice Sounder - VAD - White

C-Tec BF455ACXW CX O Class Base Voice Sounder - VAD - WhiteThe Base Mount range of addressable loop-powered basesincludes voice sounders and combined voice sounder visual alarm devices VADs.Their purpose is to visually and audibly alert building occupants of a firealarm. They are designed for use with C-TECs ZFPXFP Apollo Discovery protocolpanels and other third-party Apollo Discovery protocol panels. Howevercompatibility testing with third-party panels is recommended to ensure correctoperation.The bases offer low current consumption high sound outputhigh efficiency VADs seven selectable volume levels 15 selectable tone pairsand built-in short-circuit loop isolators.The combined sounder and VAD on the BF455ACXW andBF457ACXW bases can be set to operate independently of each other paneldependent function.All bases are designed to comply with all relevant sectionsof the fire alarm device standards EN 54-3 Sounders EN 54-23 Visual alarmdevices - VADs and EN 54-17 Short-circuit isolators.Key FeaturesSuperb sound intelligibilityIncludes three selectable voice message pairsIncludes the same electronics as our EN54-3 17certified base soundersOnboard short-circuit loop isolator550A quiescent current10mA alarm current 24V DC voice sounder on maxGroup addressing facility allows multiple devices to beoperated simultaneously7 selectable volume levelsOptional BF330CTLIDW white or BF330CTLIDR red cap availablefor stand-alone useIP21C ratedDetector spare wires includedPlease note This image is for illustrative purposes only

GBP 64.69
1

C-Tec BF432ACXW CX O Class Base Sounder VAD

C-Tec BF432ACXW CX O Class Base Sounder VAD

C-Tec BF432ACXW CX O Class Base Sounder VADThe Base Mount range of addressable loop-powered basesincludes voice sounders and combined voice sounder visual alarm devices VADs.Their purpose is to visually and audibly alert building occupants of a firealarm. They are designed for use with C-TECs ZFPXFP Apollo Discovery protocolpanels and other third-party Apollo Discovery protocol panels. Howevercompatibility testing with third-party panels is recommended to ensure correctoperation.The bases offer low current consumption high sound outputhigh efficiency VADs seven selectable volume levels 15 selectable tone pairsand built-in short-circuit loop isolators.The combined sounder and VAD on the BF455ACXW andBF457ACXW bases can be set to operate independently of each other paneldependent function.All bases are designed to comply with all relevant sectionsof the fire alarm device standards EN 54-3 Sounders EN 54-23 Visual alarmdevices - VADs and EN 54-17 Short-circuit isolators.Please note this image is for illustrative purposes only

GBP 48.60
1

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module

C-Tec CA732 CA Zone Monitor Module The C-Tec CA732 is a CA Zone monitor module using the C-TecCAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13A single-zone addressable Zone Monitor capable of supportingup to 20 conventional fire detectors and 10 MCPsMountable on a standard UK 25mm double gang back boxOnboard short-circuit loop isolator4mA typical alarm current 1.1mA typical quiescent current 22-40V DCIndicators for Loop polling input faults and relay statusAlternatively can be used as general purpose input monitorMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 44.86
1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-Tecs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts unbalanced electret microphones with 3.5mm mono jack plugs.Part of C-Tecs patented Outreach Plate audio input extension system.Compatible with C-Tecs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.59
1

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm The Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced electret microphones with 6.35mm 14 jack plugs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone Plate

C-Tec APXM XLR 3 Pin Microphone PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced microphones with standard 3 pin XLR connectors.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.30
1

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output Module

C-Tec CA730 CA Input Output ModuleThe C-Tec CA730 is an addressable input output interfacemodule using the C-Tec CAST analogue addressable protocol.CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesLPCB certified to EN54-17 18 and Kiwa Teleficationcertified to EN54-13Incorporates the functions of a switch monitor zone monitorand output unitUp to 20 conventional detectors 10 MCPsAny normally open switch with an EOL resistor fittedA simple normally open or closed switch non-faultmonitoredOnboard short-circuit loop isolator5.5mA typical alarm current 1.3mA typical quiescentcurrent 22-40V DCIndicators for Loop polling input faults and relay statusCan switch 1A30V DC or 0.3A125V ACIncludes volt free changeover contacts that can be used totrigger rollershutter doors gas shut-off valves smoke vents etcMountable on a C-TEC NCP-26 surface box or a standard UK25mm double gang back box not supplied

GBP 51.37
1

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated Microphone

C-Tec APM Omni-Directional Plated MicrophoneThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesA self-contained omni-directional plated electret microphone complete with onboard mic to line level converter.Part of C-TECs patented Outreach Plate audio input extension system.Provides up to25m2 ambient coverage or 2.5m2 direct speechcoveragewhen located at a ceiling height of 2.5 to 3m.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 53.39
1

C-Tec BF446ACXDRLD CX Wall Voice Sounder Deep Base Red Lockdown

C-Tec BF446ACXDRLD CX Wall Voice Sounder Deep Base Red Lockdown

C-Tec BF446ACXDRLD CX Wall Voice Sounder Deep Base RedLockdownThe Hi-Output range of addressable loop-powered devicesinclude voice sounders and combined voice sounder VADs. Their purpose is tovisually and audibly alert building occupants of a fire alarm. They aredesigned for use with C-TECs ZFP and XFP Apollo Discovery panels and otherthird-party Apollo Discovery panels. However compatibility testing withthird-party panels is recommended to ensure correct operation.Please note this image is for illustrativepurposes only

GBP 76.22
1

C-Tec XFP508H Hush Button Hochiki ESP Protocol

C-Tec XFP508H Hush Button Hochiki ESP Protocol

C-Tec XFP508H Hush Button Hochiki ESP ProtocolThe XFP508H Hush Button has been specifically designed to reduce the incidence of false alarms in houses of multiple occupation by providing reliable fully monitored fire detection alarm and silencing facilities inside each individual flat or apartment.It can be looked upon as a miniature loop-powered single zone fire alarm controller that sits and is addressed on an Hochiki ESP analogue loop with the ability to communicate its status back to the host panel. On a typical system one Hush Button is fitted in each dwelling complete with conventional detectors and conventional sounders to provide occupants with a simple means of invoking two types of hushed period.By providing occupants with this level of control over their fire alarm systems it helps reduce false alarms and prevent unnecessary building evacuations system vandalism and the likelihood of a true alarm signal being ignored.Key FeaturesUpgrades the level of protection offered in a flat or apartment from the Grade D minimum mainsbattery smoke alarms to Grade A or BProvides each individual dwelling with a 2 minute silence facility and 15 minute isolate facility to BS 5839 pt 6 clause 12.2Can be operated by building occupants whilst standing at floor levelIncludes a built-in loop isolator conventional sounder circuit conventional detector circuit and three status LEDsFully monitored for open and short circuit faults logging facilities at the host panel give full traceability of any problemsFailsafe operation - a general fire condition at the host panel will override any silencedisolated state at the hush button and immediately turn on its local soundersOperation of a manual call point fitted with a resistor of less than 400 ohm will immediately trigger the host panel a 330 Ohm resistor is suppliedCommon OV line allows sounders and detectors to be wired in three core cable

GBP 74.52
1

C-Tec XFP508X Hush Button Apollo XP95 Discovery Protocol

C-Tec XFP508X Hush Button Apollo XP95 Discovery Protocol

C-Tec XFP508X Hush Button Apollo XP95 Discovery ProtocolThe XFP508X Hush Button has been specifically designed to reduce the incidence of false alarms in houses of multiple occupation by providing reliable fully monitored fire detection alarm and silencing facilities inside each individual flat or apartment.It can be looked upon as a miniature loop-powered single zone fire alarm controller that sits and is addressed on an XP95 Discovery or Xplorer analogue loop with the ability to communicate its status back to the host panel. Typically one Hush Button is fitted in each dwelling complete with conventional detectors and conventional sounders to provide occupants with a simple means of invoking two types of hushed period.By providing occupants with this level of control over their fire alarm systems it helps reduce false alarms and prevent unnecessary building evacuations system vandalism and the likelihood of a true alarm signal being ignored.Key FeaturesUpgrades the level of protection offered in a flat or apartment from the Grade D minimum mainsbattery smoke alarms to Grade A or BProvides each individual dwelling with a 2-minute silence facility and 15 minute isolate facility to BS 5839 pt 6 clause 12.2Can be operated by building occupants whilst standing at floor levelIncludes a built-in loop isolator conventional sounder circuit conventional detector circuit and three status LEDsFully monitored for open and short circuit faults logging facilities at the host panel give full traceability of any problemsFailsafe operation - a general fire condition at the host panel will override any silencedisolated state at the hush button and immediately turn on its local soundersOperation of a manual call point fitted with a resistor of less than 400 ohm will immediately trigger the host panel a 330 Ohm resistor is suppliedCommon OV line allows sounders and detectors to be wired in three core cable

GBP 74.52
1

C-Tec BF365SC Sounder Isolator Controller

C-Tec BF365SC Sounder Isolator Controller

BF365SC Sounder Isolator ControllerBF365SC Conventional Sounder Controller and its associated BF365IM Isolator Modules are designed to interface to a fire alarm panels conventional sounder circuit. The Modules each of which would typically have a conventional sounder connected to it are wired in a loop arrangement beginning and ending at the controller. The Controller transforms the conventional sounder circuits monitoring and triggering voltages into its own unique control voltages which it uses to trigger the Isolator Modules and monitor the sounder loop wiring.Each Module has smart sensing which means if a wiring fault should occur the Modules nearest to the faulty section of cabling will if needed isolate this section. As the Modules are driven from each direction any loss of cable integrity will have no effect on the functionality of the actual sounders. Having a fault tolerant arrangement such as this means that low cost cabling can be used for the sounder circuit subject to the fire officers approval leading to significant savings in installation.Key FeaturesDesigned to meet requirement 17.9.2c of Dutch standard NEN2575BSI certified to EN54 parts 17 18Easily interfaced to a conventional fire alarm sounder circuitAllows low-cost non-fire resistant sounder circuit cabling to be used when used in conjunction with our BF365IM Isolator Modules subject to fire officer approval.Wiring must be made in a loop arrangement beginning and ending at the controllerIf a wiring fault should occur the Modules nearest to the faulty section of cabling will if needed isolate this section. As the Modules are driven from each direction any loss of cable integrity will have no effect on the functionality of the actual soundersFits on standard UK 25mm flush or surface mount back boxesNot suitable for use in the UK

GBP 77.21
1