28 results (0,14255 seconds)

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec ML1K ML1 Hearing Loop System

C-Tec CL1 Mini-Counter Hearing Loop Amplifier Only

C-Tec CA740 Cast 4w Conventional Zone Convertor - No PSU Included

C-Tec CA739 CAST 4 Way Sounder Controller Extendable To 8 Way ZFP ONLY

C-Tec CA736 EACIE 1 Way Flat Interface - Double Gang

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesCombines the functions of anAPXM microphone Outreach plate and an APL dual phono Outreachplate in one double gang device.Accepts balanced or unbalanced microphones with standard 3 pin XLR connectors AND dual phono line level inputs.Gives a more attractive appearance than separate side-by-side single gang Outreach Plates.Counts as one of the total of ten plates permitted aspart of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK doublegang back box.

GBP 96.35
1

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications CardAn optional system expansion device for use with XFP 12 Loop 32 Zone fire panels. Allowsthe connection of up to eight XFP Repeaters or eight XFP Main panels any mix on an RS485 network. One AFP711 card required per networked Main XFP 12 Loop 32 Zone panel note that XFP510-16 and XFP510-32 repeaters include a network driver card as standard.The AFP711 is NOT compatible with XFP Single Loop 16 Zone panels which require a CFP761 card for networking.Key network protocol features when used for interconnecting XFP main panelsCan be used to connect up to 8 XFP main panels any mix over a two-wire RS485 network of up to 1KM in length.Each networked XFP can be programmed to accept Fires Faults and Control actions such as Silence Alarm Sounders and Control Panel Resets from other panels.Each XFP will accept Disablement commands for zones sounders and output sets from other panels.All panels monitored for network wiring faults.Fires and faults on remote panels are displayed on local panels including the point description.CEs can be programmed into local panels dependent on which remote panel is in alarm.The network supports the programming of site data into remote panels from a PC at a local panel.Time and date is common to all panels.All networked main panels require a network communication card.It is not possible to mix XFP main panels and XFP repeaters on the same network.Key network protocol features when used for connecting XFP repeatersCan be used to connect up to 8 XFP repeaters any mix to one XFP main panel.Up to 500m of cable may be fitted to an XFP two-wire repeater network.Each XFP repeater offers all the functions and controls of an XFP main panel.The XFP main panel must have a network communication card fitted.It is not possible to mix XFP main panels and XFP repeaters on the same network.

GBP 114.65
1

C-Tec CA447ADR65 CA Wall Voice Sounder VAD Deep Red - IP5565

C-Tec BF447ACXSR Addressable Wall Voice Sounder VAD with Shallow Base

C-Tec BF447ACXDR Addressable Wall Voice Sounder VAD with Deep Base

C-Tec CP411T CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder

C-Tec CA47067 CA Manual Call Point Surface IP67 Red

C-Tec CA447ADR CA Wall Voice Sounder VAD - Deep - Red

C-Tec ECU723 SigTEL InterfaceNetwork Communication Card

C-Tec CP414TVR CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP411TV CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP414V CAST-PRO Smoke Heat Multisensor cw Voice Sounder

C-Tec CP414TV CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP411V CAST-PRO CO Fire Smoke Heat Multisensor cw Voice Sounder

C-Tec CP411TVR CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP414VV CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp C-3-9.4 White VAD

C-Tec CP414VVR CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp O-C-1.9-4 Red VAD