mcb.dk | Få success online

C-Tec QT612 Quantec Relay Output Device

C-Tec QT612 Quantec Relay Output DeviceProvides a zone-specific 30V 1A relay output that can be used to trigger third party strobes CCTV cameras auto-diallers building management systems and more. Can be programmed to operate in a multitude of ways using a QT432 Quantec Configurator.Key FeaturesMeasures just 56mm square x 10mm deep.Includes a diagnostic LED to aid setup.

GBP 140.20

1

C-Tec Output Expansion Relay Board EP212

C-Tec Output Expansion Relay Board EP212The EP212 is an optional system expansion device for use withthe EP203 three zone automatic extinguisher panel. Mounts inside the EP203panel to provide five volt free relay contacts reset mode discharged hold and abort.Key FeaturesReset relay switchesduring the panels reset cycleModerelay switcheswhen the extinguishant systems mode is changed to manualDischarged relay switcheswhen a released flow switch input e.g. from theextinguishant pipework is received toindicate the extinguishant has been releasedHoldrelay switcheswhen a hold input isreceived at the panel. If the panel is in 2nd stage alarm i.e. it is in automatic mode and detection circuits are activated or it is in either automaticmanual mode and a manual release input is operated the extinguishant release sequence is haltedAbortrelay switcheswhen an abort input isreceived at the paneltocancel the extinguishant release sequence

GBP 108.35

1

C-Tec ActiV Conventional Weatherproof Hi-Output W-2.75-9 Wall VAD cw Voice Sounder IP55 BF447CCCDR65

C-Tec ActiV Conventional Weatherproof Hi-Output W-2.75-9 Wall VAD cw Voice Sounder IP55 BF447CCCDR65It is compatible with C-TECs CFP FP MFP and EP203 conventional fire alarm panels and virtually all other makes testing on third-party panels is recommended before useIt is designed to be wall mounted. Can be used in covered outdoor areas.Key FeaturesProvides W-2.75-9 rated light distribution when wall mounted min. 0.4 lux over a 2.75x 9m cuboid area. Can also be used as aW-4-4 VADSuperb soundintelligibilityChoose fromtwoevacuation voice messagesand four evacuationalarm tones yourselected evacuation message will be preceded by theselected toneThree selectable VAD flash rates 0.5Hz 1Hz OFFAlarm Current at 30Vdc 17mA 0.5Hz or 24mA 1HzAlarm Current at 18Vdc 18.5mA 0.5Hz or 30mA 1HzIP55C rated weatherproofManufactured in the UK by C-TEC

GBP 105.30

1

C-Tec BF447ACXDRLD CX Wall Voice Sounder VAD Deep Base - Red Lockdown

C-Tec BF447ACXDRLD CX Wall Voice Sounder VAD Deep Base - RedLockdownThe Hi-Output range of addressableloop-powered devices include voice sounders and combined voice sounder VADs.Their purpose is to visually and audibly alert building occupants of a firealarm. They are designed for use with C-TECs ZFP and XFP Apollo Discoverypanels and other third-party Apollo Discovery panels. However compatibilitytesting with third-party panels is recommended to ensure correct operation.Pleasenote this image is for illustrative purposes only

GBP 101.59

1

C-Tec BF433CEASW Wall Sounder VID - Self Testing - White

C-Tec BF433CEASW Wall Sounder VID - Self Testing - WhiteThe BF433CEASW is a new EN54-3 compliant evacuation alert system from C-TEC specifically designed to assist the fire rescue services FRS in evacuating high-rise residential buildings. The device offers low current consumption emitting a clear concise and recognisable evacuation alarm toneDetailsDesigned for use on a C-TEC CAST-powered EVAC-ALERT system.Provides audible and visual indication of an evacuation alert to help satisfy the requirements of the Equality Act.Impressive 100dBA sound output at 1m.Low 12.2mA alarm current at 0.5Hz with sounder on max and indicator lit.IP21C rated.Designed to comply with EN54-3.

GBP 131.30

1

C-Tec BF447ACXDR Addressable Wall Voice Sounder VAD with Deep Base

C-Tec BF447ACXDR Addressable Wall Voice Sounder VAD with Deep BaseThe BF447ACXDR is a Hi-Output wall VAD with voice sounder designed with superb sound intelligibility for use with the C-Tec addressable range of control panels.Key FeaturesIncludes three selectable voice message pairsProvides W-2.4-8.2 light distribution when wallmounted min 0.4 lux over a 2.4m x 8.2mcuboidarea using the same lens and electronics as our EN54-23 3 17 certified wall sounder VADOnboard short-circuit loop isolator550A quiescent current19.5mA alarm current 24V DC VAD lit voice sounder on maxGroup addressing facility allows multiple devices to be operated simultaneously7 selectable volume levels and up to 15 selectable tone pairsIP33C Type B rated

GBP 101.59

1

C-Tec NC943B Conventional Single Zone Call Controller

C-Tec NC943B Conventional Single Zone Call ControllerThe NC943B is a single zone call controller cw a 12V 140mA PSU and standby battery. The device is fully compatible with C-TECs entire range of 800 Series Call System components.Key FeaturesCapable of indicating standard constant tone and emergency intermittent tone calls.Includes a volume adjustable sounder and a link-selectable Call AcceptReset button.Power on and Alarm CALLING LEDs.Volt-free relay output for the optional connection of externally powered beacons etc relay activates on active call signal.Standby battery provides up to 24 hours standby and 15 minutes alarm running time.Mounts on a standard UK 25mm double gang flush or surface back box.Also available as part of the NC951 Accessible Toilet Alarm Kit.

GBP 106.38

1

C-Tec BF433CEASR Wall Sounder VID - Self Testing - Red

C-Tec BF433CEASR Wall Sounder VID - Self Testing - RedThe is BF433CEASR a new EN54-3 compliant evacuation alert system from C-TEC specifically designed to assist the fire rescue services FRS in evacuating high-rise residential buildings. The device offers low current consumption emitting a clear concise and recognisable evacuation alarm tone.Details Designed for use on a C-TEC CAST-powered EVAC-ALERT system Provides audible and visual indication of an evacuation alert to help satisfy the requirements of the Equality Act Impressive 100dBA sound output at 1m Low 12.2mA alarm current at 0.5Hz with sounder on max and indicator lit IP21C rated. Designed to comply with EN54-3 White version also available order code BF433CEASW

GBP 131.30

1

C-Tec BF447ACXSR Addressable Wall Voice Sounder VAD with Shallow Base

C-Tec BF447ACXSR Addressable Wall Voice Sounder VAD with Shallow BaseThe BF447ACXSR is a Hi-Output wall VAD with voice sounder which has been designed with superb sound intelligibility for use with the C-Tec addressable range of control panels.Key FeaturesIncludes three selectable voice message pairsProvides W-2.4-8.2 light distribution when wallmounted min 0.4 lux over a 2.4m x8.2mcuboidarea using the same lens and electronics as our EN54-23 3 17 certified Wall Sounder VADOnboard short-circuit loop isolator550A quiescent current19.5mA alarm current 24V DC VAD lit voice sounder on maxGroup addressing facility allows multiple devices to be operated simultaneously7 selectable volume levels and up to 15 selectable tone pairsIP21C Type A rated

GBP 95.84

1

C-Tec CA447ADR CA Wall Voice Sounder VAD - Deep - Red

C-Tec CA447ADR CA Wall Voice Sounder VAD - Deep - RedThe CA447ADR is a red wall mounted high output addressablewall VAD and voice sounder with an IP33C deep base designed for use on C-TecCAST protocol analogue addressable fire alarm systems. CAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million-pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key FeaturesSuperb sound intelligibilityOnboard short-circuit loop isolatorFour selectable volume levelsSix selectable messages with tonesProvides W-2.75-9 or W-4-4 rated light distribution26.5mA typical alarm current 470A typical quiescentcurrent 27-40V DCGroup addressing facility allows multiple devices to beoperated simultaneouslyIP33C rated

GBP 90.85

1

C-Tec NC941SS Conventional Stainless Steel Single Zone Call Controller with PSU amp Reset Button

C-Tec NC941SS Conventional Stainless Steel Single Zone Call Controller with PSU Reset ButtonThe NC941SS is a stainless-steel single zone call controller with a built-in mains to regulated DC power supply providing 250mA at 13.5V. An on-board buzzer reset button and LED indicator are provided making it ideal for all types of single zone call communication applications including disabled persons toilet alarms. The NC941SS is compatible with all 800 Series call points ceiling pulls and remote sounders.Key FeaturesA high-quality brushedstainless-steel single zone call controller cw a 12V 250mA PSUFully compatible with C-TECs entire range of 800 Series Call System componentsCapable of indicating standard constant tone and emergency intermittent tone callsPower On and Alarm CALLING LEDsOpen collector output goes to 12V when the controllers onboard buzzer soundsMounts on a standard UK 40mm double gang flush or surface back box

GBP 171.83

1

C-Tec APXMM Mini-Mixer Plate

C-Tec APXMM Mini-Mixer PlateThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesCombines the functions of anAPXM microphone Outreach plate and an APL dual phono Outreachplate in one double gang device.Accepts balanced or unbalanced microphones with standard 3 pin XLR connectors AND dual phono line level inputs.Gives a more attractive appearance than separate side-by-side single gang Outreach Plates.Counts as one of the total of ten plates permitted aspart of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK doublegang back box.

GBP 96.35

1

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications CardAn optional system expansion device for use with XFP 12 Loop 32 Zone fire panels. Allowsthe connection of up to eight XFP Repeaters or eight XFP Main panels any mix on an RS485 network. One AFP711 card required per networked Main XFP 12 Loop 32 Zone panel note that XFP510-16 and XFP510-32 repeaters include a network driver card as standard.The AFP711 is NOT compatible with XFP Single Loop 16 Zone panels which require a CFP761 card for networking.Key network protocol features when used for interconnecting XFP main panelsCan be used to connect up to 8 XFP main panels any mix over a two-wire RS485 network of up to 1KM in length.Each networked XFP can be programmed to accept Fires Faults and Control actions such as Silence Alarm Sounders and Control Panel Resets from other panels.Each XFP will accept Disablement commands for zones sounders and output sets from other panels.All panels monitored for network wiring faults.Fires and faults on remote panels are displayed on local panels including the point description.CEs can be programmed into local panels dependent on which remote panel is in alarm.The network supports the programming of site data into remote panels from a PC at a local panel.Time and date is common to all panels.All networked main panels require a network communication card.It is not possible to mix XFP main panels and XFP repeaters on the same network.Key network protocol features when used for connecting XFP repeatersCan be used to connect up to 8 XFP repeaters any mix to one XFP main panel.Up to 500m of cable may be fitted to an XFP two-wire repeater network.Each XFP repeater offers all the functions and controls of an XFP main panel.The XFP main panel must have a network communication card fitted.It is not possible to mix XFP main panels and XFP repeaters on the same network.

GBP 114.65

1

C-Tec BF562-1 Switch Mode 24v 1.5A EN54-4 Boxed Metal PSU

C-Tec BF562-1 Switch Mode 24v 1.5A EN54-4 Boxed Metal PSUThe BF562-1 is certified to EN54-4A2 by the LPCB and VdS AFNOR pending. It comes with a plastic cover on PSU PCB which guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition.Key FeaturesMultiple indicators - supply present general fault fault type aux. equipment faultTwo selectable battery charge currentsBattery fault impedance limits can be optimised to suit load current helps extend battery lifeMains fail simulation modeImproved on-board temperature sensor with optional remote sensorElectronic functions comply with EN50131-6 grades 1-4 for security applicationsBF562-1E caged BF562-1C PCB-only versions availableTYPICAL USESIdeal for poweringbeam detectors auto-dial communicators aspirating smoke detectors auto-open vent systems auxiliary sounder systems or any other device performing a mandatory function of a fire alarm system.PSU CUSTOMISATIONThe BF562-1can be customised to suit your exact requirements using a BF423 configurator PC. Configurable parameters include float voltage temperature compensation battery charge rate mA battery impedance and configurableInputOutput settings. It is important to note changing the PSUs parameters in this way isoutside the scope of EN54-4 and any changes mustbe tested by the responsible person for correctoperation.PSU STATUS LEDlocated on the PSU PCB1 flash Mains Failure.2 flashes Battery Voltage Low.3 flashes Battery Voltage Critical.4 flashes Charger Failure.5 flashes Charger OK Battery is either actively charging or in float charge.6 flashes No Batteries Fitted indicating DIP Switch 4 position.7 flashes Battery Resistance Fault Level set by DIP Switch 2 position.8flashes Output Over Voltage.BATTERY FAULT MONITORINGThe BF562-1 complies with EN54-4A2 and therefore must monitor battery resistance. The fault threshold is directly related to the ability of the battery to deliver the rated current to the load. For example batteries stored uncharged for long periods during shipment andor distribution degrade leading to increased internal resistance. If a degraded battery is fitted a fault will be shown by the PSU as mandated by EN54-4A2.DATA PORTData on the BF562-1s status can be extracted from the PSUsbi-directional data port. The data availableincludes thermistor measurements battery terminal voltage system voltage at load terminals battery charge current load current battery impedanceandASCII text string status messages. Extracting this data requires additional equipment and permissions - contact C-TEC for details.

GBP 155.72

1

C-Tec BF560-12 Switch Mode 12v 2A EN54-4 Boxed PSU

C-Tec BF560-12 Switch Mode 12v 2A EN54-4 Boxed PSUThe C-Tec BF560-12 12V 2A EN54-4 Switch Mode PSU is ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities. It is certified to EN54-4A2 by the LPCB VdS AFNOR pending.Key FeaturesMultiple indicators - supply present general fault fault type aux. equipment fault.Two selectable battery charge currents.Battery fault impedance limits can be optimised to suit load current helps extend battery life.Mains fail simulation mode.Improved on-board temperature sensor with optional remote sensor.Ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities.Electronic functions comply with EN50131-6 grades 1-4 for security applications.BF560-12E Caged BF560-12C PCB-only versions available.Plastic cover on PSU PCB guards against touching live parts.Includes a single-pole voltfree changeover relay that switches for any fault condition.Additional InformationPSU CUSTOMISATIONThe BF560-12can be customised to suit your exact requirements using a BF423 configurator PC. Configurable parameters include float voltage temperature compensation battery charge rate mA battery impedance and configurableInputOutput settings. It is important to note changing the PSUs parameters in this way isoutside the scope of EN54-4 and any changes mustbe tested by the responsible person for correctoperation.12V SECURITY STUUSED PURELY FOR FIRE ALARM SIGNALLINGThe BF560-12 can help combat an area of fire alarm system non-compliance that is often overlooked - their connection to remote monitoring centres via 12V security STUs or autodiallers. Firesystems that require such monitoring are typically connected to 12V security STUs. Unfortunately PSUs used to power these STUs normally only offer 12 hours standby are notconnected to a dedicated mains supply and do not include the features demanded by EN54-4 such as battery impedance monitoring temperature compensated charging CPR compliance etc. TheBF560-12 solves these problems by allowing the use of 12V STUs with a cost-effective EN54-4 compliant PSU thereby facilitating compliance with BS5839-1 or European equivalents. Tofurther assist this application an optional STU mounting plate is available for inside the BF560-12 order code BF360SP.PSU STATUS LEDlocated on the PSU PCB1 flash Mains Failure.2 flashes Battery Voltage Low.3 flashes Battery Voltage Critical.4 flashes Charger Failure.5 flashes Charger OK Battery is either actively charging or in float charge.6 flashes No Batteries Fitted indicating DIP Switch 4 position.7 flashes Battery Resistance Fault Level set by DIP Switch 2 position.8flashes Output Over Voltage.BATTERY FAULT MONITORINGThe BF560-12 complies with EN54-4A2 and therefore must monitor battery resistance. The fault threshold is directly related to the ability of the battery to deliver the rated current to the load. For example batteries stored uncharged for long periods during shipment andor distribution degrade leading to increased internal resistance. If a degraded battery is fitted a fault will be shown by the PSU as mandated by EN54-4A2.EN50131-6 POWER SUPPLIES FOR INTRUSION HOLD UP ALARMS CAPABILITYThe power supply inside the BF560-12 has all the electrical functions required to comply with EN50131-6 Grade 4which includes Grades 3 2 and 1. However the BF560-12s enclosure isnot designed to comply with the standardsrequirements totriggeranalarm if someone tries to force the box open. OEM security companies interested in utilising the BF560-12s PSUPCB inside their own EN50131-6 compliant tamper-resistant enclosures should contact our marketing departmentfor further detailson costs and approvals.DATA PORTData on the BF560-12s status can be extracted from the PSUsbi-directional data port. The data availableincludes thermistor measurements battery terminal voltage system voltage at load terminals battery charge current load current battery impedanceandASCII text string status messages. Extracting this data requires additional equipment and permissions -call C-TEC for details.

GBP 113.64

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)