65 results (0,15729 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec QT42410 Ten-Way Charging Unit for QT412

C-Tec QT42410 Ten-Way Charging Unit for QT412

C-Tec QT42410 Ten-Way Charging Unit for QT412The QT42410 ten-way charging unit can simultaneously charge up to ten QT412 Range dual action infraredradio transmitters. Designed to be powered from a 230V a.c. mains source using the standard IEC lead supplied the unit can be wall or desk mounted to suit the transmitter storage and charging requirements of a particular site.Key FeaturesA ten-way plugtop charger designed for use with Quantecs QT412 range of IRRF transmitters.Can simultaneously charge up to ten transmitters.Connects to a standard 13A mains socket using the standard IEC lead suppliedCan be wall or desk mounted to suit the transmitter storagecharging requirements of a particular site.Fully recharged transmitters can be left connected to the charger with no detrimental effect.14-hour typical charging time full cycle.Indicators confirm when charging is complete.

GBP 265.99
1

C-Tec BF364 Single Gang Locking Jack Socket

C-Tec BF364 Single Gang Locking Jack Socket

Please note that this product is now obsolete. The replacement isC-Tec BF320JP XLR Connector Plate for BF320C-Tec BF364 Single Gang Locking Jack Socket for use with BF363The BF364 allows the BF363 Vibrating Pillow Pad to be connected to a 24V DC conventional fire alarm sounder circuit. The BF364 typically used to provide early warning of a potential fire alarm condition to the hard of hearing.Key FeaturesMax operating voltage 27V DCMounts on a standard UK 18mm single gang flush or surface back boxIncludes Braille text

GBP 37.43
1

C-Tec NC802DB Conventional Call Point with Button Reset and Remote Socket

C-Tec NC802DB Conventional Call Point with Button Reset and Remote Socket

C-Tec NC802DB Conventional Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been made.Onboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone such as ceiling pull units in en-suite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 27.18
1

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote Socket

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote Socket

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been madeOnboard reset button cancels Standard and Emergency calls made from the NC802DEB-12 and Standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 43.27
1

C-Tec PDA103I Intercom AFILS IP65 Surface

C-Tec PDA103I Intercom AFILS IP65 Surface

C-Tec PDA103I Intercom AFILS IP65 SurfaceThe PDA103I is a self-contained hearing loop system specifically designed to integrate with disabled refuge door entry and intercom help points.Key FeaturesHelps satisfy the accessibility and integrated loop requirements of the Equality Act and the 2018 revision of BS 8300Housed in an attractive surface-mounting IP65 rated enclosure for use in indoor or outdoor areasSupplied with a plugtop power supply if no plug socket is available replace with an appropriate 110-240Vac 5060Hz Mains power supplyAdjustable controls allow the amplifiers input and output stages to be set to suit the exact characteristics of the applicationState-of-the-art audio processor helps suppress loud noises hisses clicksIncludes internal Limit Peak Loop Fault and Power On indicatorsExceeds the requirements of PD IEC TR 63079 BS7594 EN60118-4 when correctly installed

GBP 361.32
1

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote Socket

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote Socket

C-Tec NC802DERM Conventional Infrared Call Point with Magnetic Reset and Remote SocketA button operated call point which comes with an infrared receiver capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a magnetic reset target that requires an NC803M magnetic reset key to operate.Onboard infrared receiver will accept Standard Emergency calls from compatible 800 Series infrared transmitters. Calls can also be made by activating the call points CALL button to make a Standard call and the call points CALL RESET target together for an emergency call.Key FeaturesIncludes a6.35mm jack plug socket for the connection of an optional tail call lead or other ancillary calling deviceRed reassurance LED confirms a call has been madeOnboardmagentic reset target cancels Standard and Emergency calls made from the NC802DEWM and Standard calls made from other devices on the same zoneCan be connected to up to 3 NC302RXCS slave infrared ceiling receivers to increase coverageMounts on a standard UK 25mm single gang flush or surface back box

GBP 63.59
1

C-Tec NC805C14 Tail Call Lead 4.2m 14ft

C-Tec NC805C14 Tail Call Lead 4.2m 14ft

C-Tec NC805C14 Tail Call Lead 4.2m 14ftA long 4.2m tail call lead for use with C-TECs Quantec and 800 Series Call Systems. It allows usersto remotely generate Standard calls from armchairs beds etc.Key FeaturesEasily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call pointsActivating the pear push or removing the tail call lead from a call points remote socket will generate a Standard callComprises a pear-shaped call push 4.2m14ft trailing lead and a 6.35mm remote jack plug

GBP 15.54
1

C-Tec NC805C6 Tail Call Lead 1.8m 6ft

C-Tec NC805C6 Tail Call Lead 1.8m 6ft

C-Tec NC805C6 Tail Call Lead 1.8m 6ftA short 1.8mtail call lead for use with C-TECs Quantec and 800 Series Call Systems. It allows usersto remotely generate Standard calls from armchairs beds etc.Key FeaturesEasily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call pointsActivating the pear push or removing the tail call lead from a call points remote socket will generate a Standard callComprises a pear-shaped call push 1.8m 6ft trailing lead and a 6.35mm remote jack plug.

GBP 13.82
1

C-Tec NC805D Coiled Tail Call Lead 1.2-3.6m 4-12ft

C-Tec NC805D Coiled Tail Call Lead 1.2-3.6m 4-12ft

C-Tec NC805D Coiled Tail Call Lead 1.2-3.6m 4-12ftAn extendable coiled tail call lead for use with C-tecs Quantec and 800 Series Call Systems. Allows usersto remotely generate Standard calls from armchairs beds etc.Key FeaturesComprises a pear-shaped call push coiled1.2-3.6mtrailing lead and a 6.5mm remote jack plugEasily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call pointsActivating the pear push or removing the tail call lead from a call points remote socket will generate a Standard call

GBP 21.17
1

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet SensorDesigned to trigger a call when moisture is detected in a patients bed. Connects to Quantec via the jack socket on the QT637 Enuresisgeneral purpose interface socket. Typically positioned across and over amattress directly underneath the bed sheet.Key FeaturesProtects against patient discomfort and reduces the number of incontinence checks staff are required to make.Measures 80cm x 12cm and is supplied with a 2m lead and normally open right angled jack plug.Wipe clean design - can be re-used many times.

GBP 34.24
1

C-Tec QT634 Chair Exit Mat

C-Tec QT634 Chair Exit Mat

C-Tec QT634 Chair Exit MatDesigned to trigger a call by sensing the pressure change when a patient exits a chair. Connects to Quantec via the remote jack socket on a QT637 EnuresisGeneral Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call. Measures 400mm x 250mmand is supplied with a 2m lead and normally closed right angled jack plug.

GBP 36.64
1

C-Tec QT633 Bed Exit Mat

C-Tec QT633 Bed Exit Mat

C-Tec QT633 Bed Exit MatDesigned to trigger a call by sensing the pressure change when a patient exits a bed. Connects to Quantec via the remote jack socket on a QT637 EnuresisGeneral Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call.Key FeaturesTypically positioned across and overamattress directly underneath the bedsheet.Measures 80cm x 10cm and is supplied with a 2m lead and normally closed right angled jack plug.

GBP 34.70
1

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 164.82
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05

C-Tec Moflash EX Intrinsically Safe Beacon with White Lens IS-B-02-05This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02

C-Tec Moflash EX Intrinsically Safe Beacon with Red Lens IS-B-02-02This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 164.82
1