mcb.dk | Få success online

Apollo RW1700-030APO Reach XP95 Loop Interface Module

Apollo RW1700-030APO Reach XP95 Loop Interface ModuleThe RW1700-030APO is a wired loop interface that bridges REACH Wireless radio-frequency products to an Apollo wired loop. Communication between the wireless products are translated to Apollo wired protocol for operation via the wired fire panel.The REACH range is designed to solve challenging installation scenarios for structures with restricted or complex access and installation conditions such as listed buildings out-buildings temporary structures where wired installation or long site downtime is not possible.Key FeaturesBuilt-in LCD DisplayPhysical Navigation Buttons3x Status LEDs Fault Configuration and PowerLoop-poweredBuilt-in IsolatorBi-directional wireless communicationDual channel redundancyFive year product warranty

GBP 262.32

1

Apollo Xpander Diversity Loop Interface Unit - XPA-IN-14050-APO

Please note The XPA-IN-14050-APO does not support CoreProtocol installations.Apollo Xpander Diversity Loop Interface Unit - XPA-IN-14050-APOThe XPander Diversity Loop Interface Unit can monitor up to 31 XPander devices and report each devices status to an intelligent fire control panel.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesConnects up to 31 XPander devices to an ApolloAddressable loopTranslates radio signals from XPander detectors to the fire control panelBuilt-in loop isolatorLoop-poweredDiversity aerial design for improved signal integrityThe entire XPander product line has a temporary four-month supply disruption starting from November 2021 with supply expecting to resume in February 2022.

GBP 337.68

1

Apollo DIN-Rail Interface Enclosure 10 units 29600-240

Apollo DIN-Rail Interface Enclosure 10 units 29600-240DIN-Rail Interface Enclosures are available in two sizes and can be used for housing intrinsically safe IS barriers or DIN-Rail mounted interfaces. A multi-purpose label that features a section for use with IS systems is supplied. For non-IS systems the part referring to IS can simply be removed.ApplicationThe enclosures can be used for housing intrinsically safe I.S. barriers XP95 or Soteria DIN-rail mounted interfaces. The IP67 rated enclosures have a frosted polycarbonate lid through which LEDs can be viewed. A multi-purpose label that features a section for use with I.S. systems is supplied. For non-I.S. systems the part referring to I.S. can simply be removed.Key FeaturesAllows multiple interfaces to be housed togetherIP67 rated

GBP 114.18

1

Apollo DIN Rail Interface Enclosure 29600-239

Apollo DIN Rail Interface Enclosure - 29600-239The enclosures can be used for housing intrinsically safe IS barriers or DIN-rail mounted interfaces. The enclosures have a frosted polycarbonate lid through which LEDs can be viewed. A multi-purpose label that features a section for use with IS systems is supplied. For non-IS systems the part referring to IS can simply be removed.When using these enclosures with intrinsically safe systems it is important that segregation be provided between the IS and non-IS circuits. A distance of at least 50mm must be preserved between live conducting parts of IS and other circuits. If the enclosure is used as part of an IS circuit then it must always be installed inside the safe area. Never install these enclosures in the hazardous area.The smaller enclosure is suitable for one analogue addressable or two conventional IS circuits or up to four DIN-rail interfaces.Key FeaturesAllows multiple Interfaces to be housed togetherIP67 Rated

GBP 102.76

1

Apollo RW1300-260APO REACH Sounder VAD Base - Black

Apollo RW1300-260APO REACH Sounder VAD Base - BlackThe RW1300-260APO is a wireless analogue addressable sounderVAD bases that can be used as a stand-alone notification device with ablanking cap or as a combined solution with a REACH Wireless detector.Device AddressingDevice addressing is handled by the REACH WirelessLoop Interface device RW1700-030APO. Devices are soft-addressed automaticallywhen pairing with the Loop Interface and can be changed manually.Hard-addressing using Apollo XPERT cards are not supported.Key FeaturesCompatible only with REACH Wireless16 tone pairsFour volume settingsBi-directional wireless communicationDual-channel redundancyFive-year battery life

GBP 287.00

1

Apollo RW1000-660APO REACH Optical Smoke Detector Black Body

Apollo RW1000-660APO REACH Optical Smoke Detector Black BodyThe RW1000-660APO is a wireless addressable optical smokedetector that utilises dual-optical smoke detection technology for improvedperformance maintaining the highest levels of false-alarm rejection.Device AddressingDevice addressing is handled by the REACH WirelessLoop Interface device RW1700-030APO.Devices are soft-addressed automatically when pairing withthe Loop Interface and can be changed manually. Hard-addressing using ApolloXPERT cards are not supported.CommunicationREACH Wireless Devices use radio-frequency wireless communicationto connect to the Loop-Interface.The Loop-Interface RW1700-030APO translates the wireless communicationinto wired Apollo protocol communication with each device addressableindividually by the fire panel. Tamper detectionREACH Wireless devices contain an anti-tamper mechanism. In theevent of removal from its base it sends a tamper detection message to theLoop-Interface.Key FeaturesTwin alarm bi-colour LEDs for 360 visibilityAdvanced dual-optical chamber designAdvanced drift compensationBi-directional wireless communicationDual-channel redundancyTen-year battery life

GBP 178.81

1

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413The 29600-413 is a spare singular blank XPERT card in white which has been designed for use with the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.20

1

Apollo XPander Dual Input Output Channel Unit - XPA-IN-14012-APO

Apollo XPander Dual Input Output Channel Unit - XPA-IN-14012-APOThe XPander InputOutput Unit is a radio based interface and offers two monitored input circuits and two relay outputs. It can be used for controlling fire doors fire dampers smoke vents and other fire engineering applications.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessMonitored switch circuitVoltage-free contacts Capable of switching up to 30V at 1AFive-year battery life using standard AA alkaline batteries

GBP 237.64

1

Apollo RW1000-460APO REACH Heat Detector Black Body

Apollo RW1000-460APO REACH Heat Detector Black BodyThe RW1000-460APO is a wireless analogue addressable heatdetector that can be configured as either rate-of-rise A1R or hightemperature BS classification as specified in the EN 54-5. Multiple EN 54-5classes A1R and BS can be chosen from configuration software or thekeyboardLCD interface during the link phase.Operating PrinciplesThe REACH Wireless Heat Detectors are flexible offering either static BS or rate-of-rise A1R functionality.Status LEDIt also includes a 360 LED indicator which illuminates red or green to indicate status conditions.Device AddressingDevice addressing is handled by the REACH Wireless Loop Interface device RW1700-030APO. Devices are soft-addressed automatically when pairing with the Loop Interface and can be changed manually. Hard-addressing using Apollo XPERT cards are not supported.Key FeaturesTwin alarm bi-colour LEDs for 360 visibilityProgrammable for rate-of-rise A1R or static temperatureBSBi-directional wireless communicationDual-channel redundancyTen-year battery life

GBP 178.81

1

Apollo Blank XPert Card for XPander Wireless Range -Red 29600-399

Apollo Blank XPert Card for XPander Wireless Range RedSpare singular blank XPERT card in red for the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Brand Featuresmodern styling loop-powered interface operating on 868MHz wireless addresses seen by control panel as normal addresses radio base with wireless circuitry and battery compartment chamber designed to inhibit dirt penetration and thus reduce false alarms automatic drift compensation with DirtAlert warning algorithms for transient alarm rejection FasTest reduces time taken to test detectors remote test facility 3-5 years battery lifeProduct InformationAddress card supplied with all bases. Using a coding guide pips are removed to set the address of the inserted device.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.24

1

Apollo XPander Combined Sounder Beacon Base XPA-WB-14037-APO

Apollo XPander Combined Sounder Beacon BaseXPA-WB-14037-APOThe XPander Combined Sounder and Detector is wireless and designed to provide one-point detection and notification.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of four tone pairsCertified to EN 54-25

GBP 368.42

1

Apollo XPA-MC-14101-APO XPander Manual Call Point - Integral Radio Base

Apollo XPA-MC-14101-APO XPander Manual Call Point - Integral Radio BaseThe XPander Manual Call Point is compliant with EN 54-11 and is a wireless device.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Please note The image is for illustrative purposes only.

GBP 164.53

1

Apollo XPander Sounder Beacon and A1R Heat Detector XPA-CB-14021-APO

Apollo XPander Sounder Beacon and A1R Heat DetectorXPA-CB-14021-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 372.43

1

Apollo XPander Sounder Beacon and CS Heat Detector XPA-CB-14022-APO

Apollo XPander Sounder Beacon and CS Heat DetectorXPA-CB-14022-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 372.43

1

Apollo XPander Manual Call Point Integral Radio Base - XPA-MC-14006-APO

Apollo XPander Manual Call Point Integral Radio Base XPA-MC-14006-APOThe XPander Manual Call Point is compliant with EN 54-11. It is wireless and is powered by two independent packs of three AA alkaline batteries with a typical five year life.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessXPERT addressingResettable elementFast response reports an alarm in under one secondLED to indicate operation

GBP 131.14

1

Apollo XPander 868MHz Diversity Survey Kit XPA-TE-14075-APO

Apollo XPander 868MHz Diversity Survey Kit XPA-TE-14075-APOThe XPander Diversity Survey kit is used at the site survey stage to ascertain if a site is suitable for an XPander installation. A site survey must be carried out before XPander can be installed. The Diversity Survey Kit is compliant to BS 5839-1.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesIndicates the suitability of proposed device location

GBP 369.71

1

Apollo XPander Single Input Output Channel Unit - XPA-IN-14011-APO

Apollo XPander Single Input Output Channel Unit - XPA-IN-14011-APOThe XPander InputOutput Unit is a radio based interface and offers two monitored input circuits and two relay outputs. It can be used for controlling fire doors fire dampers smoke vents and other fire engineering applications.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessMonitored switch circuitVoltage-free contactsCapable of switching up to 30V at 1AFiveyear battery life using standard AA alkaline batteries

GBP 198.37

1

Apollo XPander Amber Beacon with White Mounting Base - XPA-CB-14004-APO

Apollo XPander Amber Beacon with White Mounting Base - XPA-CB-14004-APOThe XPander Sounder and Sounder Base is wireless and designed to be used with XPander detectors and manual call points.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 321.25

1

Apollo XPander Sounder Beacon and Optical Smoke Detector XPA-CB-14020-APO

Apollo XPander Sounder Beacon and Optical Smoke DetectorXPA-CB-14020-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectors remote test facility3-5 years battery life

GBP 370.69

1

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APO

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APOThe XPander Sounder and Sounder Base is wireless and designed to be used with XPander detectors and manual call points.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self-test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring.The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessBi-directional monitored radio platformChoice of 32 selectable tonesAudible self-test availableOutput is between 92 and 106dbA at 1m dependent on tone setting

GBP 372.43

1

Apollo Auto-Aligning Beam Detector 8-50m 29650-069

Apollo Auto-Aligning Beam Detector 8-50m 29650-069The high-performance Auto-Aligning Beam Detector comprises of a ground level controller detector head with auto-aligning feature integral laser for rapid initial alignment and single prism. An additional detector head can be added to the controller.Brand FeaturesAuto-compensates for building movement and contaminationIntegral laser and auto-align enable quicker installationLow-level system controller with LCD display and user-friendly interface

GBP 688.63

1

Apollo XPander Combined Sounder Base XPA-WB-14036-APO

Apollo XPander Combined Sounder BaseXPA-WB-14036-APOThe XPander Combined Sounder and Detector is wireless and designed to provide one-point detection and notification.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessAvailable with a choice of XPander detectorsBi-directional monitored radio platformA choice of four tone pairsCertified to EN 54-25

GBP 318.79

1

Apollo Auto-Aligning Beam Detector Additional Head 8-50m 29650-070

Auto-Aligning Beam Detector Additional Head 8-50m 29650-070DescriptionAdditional Head for the Auto-Aligning Beam Detector.The high-performance Auto-Aligning Beam Detector comprises of a ground level controller detector head with auto-aligning feature integral laser for rapid initial alignment and single prism. An additional detector head can be added to the controller.Brand FeaturesAuto-compensates for building movement and contaminationIntegral laser and auto-align enable quicker installationLow-level system controller with LCD display and user-friendly interface

GBP 576.89

1

Apollo Mounting Plate for 4 Prisms 100m 29600-529

Apollo Mounting Plate for 4 Prisms 100m 29600-529Mounting Plate 4 Prisms.Auto-Aligning Beam Detector DescriptionThe high-performance Auto-Aligning Beam Detector comprises of a ground level controller detector head with auto-aligning feature integral laser for rapid initial alignment and single prism. An additional detector head can be added to the controller.Brand InformationAuto-compensates for building movement and contaminationIntegral laser and auto-align enable quicker installationLow-level system controller with LCD display and user-friendly interface

GBP 88.92

1

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527Universal Bracket for the Auto-Aligning Beam Detector.Auto-Aligning Beam Detector DescriptionThe high-performance Auto-Aligning Beam Detector comprises of a ground level controller detector head with auto-aligning feature integral laser for rapid initial alignment and single prism. An additional detector head can be added to the controller.Brand InformationAuto-compensates for building movement and contaminationIntegral laser and auto-align enable quicker installationLow-level system controller with LCD display and user-friendly interface

GBP 164.20

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)

Apollo RW1700-030APO Reach XP95 Loop Interface Module

Apollo Xpander Diversity Loop Interface Unit - XPA-IN-14050-APO

Apollo DIN-Rail Interface Enclosure 10 units 29600-240

Apollo DIN Rail Interface Enclosure 29600-239

Apollo RW1300-260APO REACH Sounder VAD Base - Black

Apollo RW1000-660APO REACH Optical Smoke Detector Black Body

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413

Apollo XPander Dual Input Output Channel Unit - XPA-IN-14012-APO

Apollo RW1000-460APO REACH Heat Detector Black Body

Apollo Blank XPert Card for XPander Wireless Range -Red 29600-399

Apollo XPander Combined Sounder Beacon Base XPA-WB-14037-APO

Apollo XPA-MC-14101-APO XPander Manual Call Point - Integral Radio Base

Apollo XPander Sounder Beacon and A1R Heat Detector XPA-CB-14021-APO

Apollo XPander Sounder Beacon and CS Heat Detector XPA-CB-14022-APO

Apollo XPander Manual Call Point Integral Radio Base - XPA-MC-14006-APO

Apollo XPander 868MHz Diversity Survey Kit XPA-TE-14075-APO

Apollo XPander Single Input Output Channel Unit - XPA-IN-14011-APO

Apollo XPander Amber Beacon with White Mounting Base - XPA-CB-14004-APO

Apollo XPander Sounder Beacon and Optical Smoke Detector XPA-CB-14020-APO

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APO

Apollo Auto-Aligning Beam Detector 8-50m 29650-069

Apollo XPander Combined Sounder Base XPA-WB-14036-APO

Apollo Auto-Aligning Beam Detector Additional Head 8-50m 29650-070

Apollo Mounting Plate for 4 Prisms 100m 29600-529

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527

Powered by Cobiro