mcb.dk | Få success online

Apollo Series 65 Auxiliary Relay Base 45681-246APO

Apollo Series 65 Auxiliary Relay Base - 45681-246OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Product InformationThe Series 65 Auxiliary Relay Base provides two sets of volt-free changeover contacts to facilitate the switching of a remote LED or other auxiliary device.Key FeaturesDetector locking mechanismOne way fitEasy to wireContains an earth connector

GBP 18.80

1

Apollo Series 65 Standard Relay Base 45681-245APO

Apollo Series 65 Standard Relay Base - 45681-245OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Product InformationThe Series 65 Standard Relay Base provides one set of volt-free changeover form C contacts that change state when the detector signals an alarm.Key FeaturesDetector locking mechanismOne-way fitEasy to wireContains an earth connector

GBP 18.71

1

Apollo Orbis Conventional Duct Smoke Detector - 53546-023APO

Apollo Orbis Conventional Duct Smoke Detection - 53546-023APOThe Conventional Duct Smoke Detector provides early detection of smoke in the air moving through heating and ventilation HVAC ducts in commercial and industrial premises. Its purpose is to prevent the re-circulation of smoke from an area on fire to areas unaffected by the fire when used with a Orbis detector. It provides a volt-free changeover relay rated at 30V 1A.Key Features For use with Orbis detectorsOperates in air speeds of 0.5ms to 20msTransparent cover to view detector head LEDIntegral smoke test portVolt-free contacts

GBP 71.44

1

Apollo Series 65 Conventional Duct Smoke Detector - 53546-021APO

Apollo Conventional Duct Smoke Detection - 53546-021APOThe Conventional Duct Smoke Detector provides early detection of smoke in the air moving through heating and ventilation HVAC ducts in commercial and industrial premises. Its purpose is to prevent the re-circulation of smoke from an area on fire to areas unaffected by the fire when used with a Series 65 detector. It provides a volt-free changeover relay rated at 30V 1A.Key Features For use with Series 65 detectorsOperates in air speeds of 0.5ms to 20msTransparent cover to view detector head LEDIntegral smoke test portVolt-free contacts

GBP 71.44

1

Apollo Dual Switch Manual Call Point SA5900-011APO

Apollo Dual Switch Manual Call Point SA5900-011APOThe Apollo Dual Switch Manual Call Point provides volt free double pole change-over contacts suitable for normally open or normally closed multiple switching from a single activation point. A device is activated by pressing the resettable element. An activation status is indicated through the rotation of the resettable element displaying yellow and black indication bars. The manual call point can be easily reset from the front using the supplied reset key.Key FeaturesResettable operating elementEasy access front reset mechanismErgonomic reset keyDouble pole change-over contactsSuitable for semi flush or surface mountingOptional transparent hinged cover

GBP 16.68

1

Apollo SA4700-302APO Intelligent DIN-Rail Input Output Unit

Apollo SA4700-302APO Intelligent DIN-Rail Input Output UnitThe Intelligent DIN-Rail InputOutput Unit providessupervision of one or more normally open volt free contactsconnected to a single pair of cables and a set of changeoverrelay output contacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent DIN-Rail InputOutput Unit is designed to be mounted on a 35 mm width DIN-Rail inside an enclosure.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 56.90

1

Apollo SA4700-300APO Intelligent DIN-Rail Switch Monitor

Apollo SA4700-300APO Intelligent DIN-Rail Switch MonitorThe Intelligent DIN-Rail Switch Monitor is designed tomonitor the state of one or more single pole volt-free contactsconnected on a single pair of cables and to report the status.It has a selectable status reporting delay making it suitable formonitoring flow switches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent DIN-Rail Switch Monitor is designed to be mounted on a 35 mm width DIN-Rail inside an enclosure.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsConfigurable input stylesEarth fault monitoring

GBP 47.69

1

Apollo Series 65 BR Heat Detector - 55000-127APO

Apollo Series 65 BR Heat Detector - 55000-127APOThe Series 65 Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 12 heat detectors in the Series 65 range designed to suit a wide variety of operating conditions. Apollo Series 65 smoke heat detector range are a direct replacement for the earlier Series 60 devices. Series 65 detectors have a wide voltage range 9-33 volt DC and can be integrated on to security systems when used with the 12 volt relay base 45681-508.The heat detector operates by using a matched pair of thermistors to sense heat. One thermistor is exposed to the ambient temperature the other is sealed. In normal conditions the two thermistors register similar temperatures but on the development of a fire the temperature recorded by the exposed thermistor will increase rapidly resulting in an imbalance of the thermistors and causing the detector to change to the alarm state.A1R BR and CR are Rate of Rise detectors designed to detect a fire as the temperature increases but they also have a fixed upper limit at which the detector will go into alarm if the rate of temperature increase has been too slow to trigger the detector earlier.Key Features Can be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsWide operating voltageFlashing LED and magnet operated test switch option

GBP 14.72

1

Apollo Series 65 CS Heat Detector - 55000-137APO

Apollo Series 65 CS Heat Detector - 55000-137APOThe Series 65 Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 12 heat detectors in the Series 65 range designed to suit a wide variety of operating conditions. Apollo Series 65 smoke heat detector range are a direct replacement for the earlier Series 60 devices. Series 65 detectors have a wide voltage range 9-33 volt DC and can be integrated on to security systems when used with the 12 volt relay base 45681-508.The heat detector operates by using a matched pair of thermistors to sense heat. One thermistor is exposed to the ambient temperature the other is sealed. In normal conditions the two thermistors register similar temperatures but on the development of a fire the temperature recorded by the exposed thermistor will increase rapidly resulting in an imbalance of the thermistors and causing the detector to change to the alarm state.A1R BR and CR are Rate of Rise detectors designed to detect a fire as the temperature increases but they also have a fixed upper limit at which the detector will go into alarm if the rate of temperature increase has been too slow to trigger the detector earlier.Key Features Can be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsWide operating voltageFlashing LED and magnet operated test switch option

GBP 14.72

1

Apollo Series 65 CR Heat Detector - 55000-132APO

Apollo Series 65 CR Heat Detector - 55000-132APOThe Series 65 Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 12 heat detectors in the Series 65 range designed to suit a wide variety of operating conditions. Apollo Series 65 smoke heat detector range are a direct replacement for the earlier Series 60 devices. Series 65 detectors have a wide voltage range 9-33 volt DC and can be integrated on to security systems when used with the 12 volt relay base 45681-508.The heat detector operates by using a matched pair of thermistors to sense heat. One thermistor is exposed to the ambient temperature the other is sealed. In normal conditions the two thermistors register similar temperatures but on the development of a fire the temperature recorded by the exposed thermistor will increase rapidly resulting in an imbalance of the thermistors and causing the detector to change to the alarm state.A1R BR and CR are Rate of Rise detectors designed to detect a fire as the temperature increases but they also have a fixed upper limit at which the detector will go into alarm if the rate of temperature increase has been too slow to trigger the detector earlier.Key Features Can be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsWide operating voltageFlashing LED and magnet operated test switch option

GBP 14.72

1

Apollo Series 65 A1R Heat Detector - 55000-122APO

Apollo Series 65 A1R Heat Detector - 55000-122The Series 65 Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 12 heat detectors in the Series 65 range designed to suit a wide variety of operating conditions. Apollo Series 65 smoke heat detector range are a direct replacement for the earlier Series 60 devices. Series 65 detectors have a wide voltage range 9-33 volt DC and can be integrated on to security systems when used with the 12 volt relay base 45681-508.The heat detector operates by using a matched pair of thermistors to sense heat. One thermistor is exposed to the ambient temperature the other is sealed. In normal conditions the two thermistors register similar temperatures but on the development of a fire the temperature recorded by the exposed thermistor will increase rapidly resulting in an imbalance of the thermistors and causing the detector to change to the alarm state.A1R BR and CR are Rate of Rise detectors designed to detect a fire as the temperature increases but they also have a fixed upper limit at which the detector will go into alarm if the rate of temperature increase has been too slow to trigger the detector earlier.Key Features Can be used for applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsWide operating voltageFlashing LED and magnet operated test switch optionWide-operating voltage of 933 V DCWide-operating and storage temperature of -20C to 60CCan be used on security systemsElectrically and mechanically compatible with Series 60Proven detection performance

GBP 14.00

1

Apollo SA4700-100APO Intelligent Switch Monitor

Apollo SA4700-100APO Intelligent Switch MonitorThe Intelligent Switch Monitor is designed to monitor thestate of one or more single pole volt-free contacts connectedon a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flowswitches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent Switch Monitor is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsPriority mode for fast responseConfigurable input stylesEarth fault monitoring

GBP 46.70

1

Apollo XP95 Mini Switch Monitor - 55000-760APO

Apollo XP95 Mini Switch Monitor - 55000-760APOThe Mini Switch Monitor is an interface within an entirely new housing. Designed in response to customer feedback thesmaller Mini Switch Monitor can be fitted onto a 35mm DIN-Rail with a twist-click motion or mounted in an enclosure such as a manual call point.It is designed to monitor the state of one or more single pole volt free contacts connected to a single pair of cables and to report the status to Apollo compatible control equipment.The monitor is designed to fit into equipment with limited space or to be mounted within an enclosure such as a manual call point. The interrupt feature means the monitor can be used where a priority response is required in particular for monitoring an individual or a cone of conventional manual call points.

GBP 42.22

1

Apollo Marine DIN-Rail Switch Monitor Plus 55000-772MAR

Apollo Marine DIN-Rail Switch Monitor Plus 55000-772MARThe Marine DIN-Rail Switch Monitor Plus is designed to monitor the state of one or more single pole volt free contacts connected on a single pair of cables and to report the status to Apollo compatible analogue control equipment. In addition it incorporates additional circuitry to monitor flow switches and provide a time delay in so doing. It also contains circuitry which can be used to reset a beam detector.OperationThe Marine DINRail switch monitor provides four input states to the control equipment normal fault pre-alarm and alarm. The unit has a red LED to indicate an alarm and a yellow LED to indicate a fault condition. The Marine DINRail switch monitor is loop-powered and operates at 1728V DC with protocol voltage pulses of 59V. The unit is designed to accept a maximum line resistance of 50ohm. The end-of-line resistor required is 20k ohm.

GBP 75.87

1

Apollo SA4700-104APO Intelligent Twin Input Output Unit

Apollo SA4700-104APO Intelligent Twin Input Output UnitThe Intelligent Twin InputOutput Unit provides the functionof two InputOutput Units within one enclosure. The twounits are electrically independent of each other. There is a DILswitch on each unit to set the address.Both inputoutput units in the enclosure provide supervisionof one or more normally open volt free contacts connectedto a single pair of cables and a set of changeover relay outputcontacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent Twin InputOutput Unit is available in the new faceplate style enclosure. This can be mounted with the supplied backbox for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 77.62

1

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247APO

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Options45681-247 for circuits having a supply voltage between 9- and 18-volts DC and 45681-248 for circuits having a supply voltage between 16- and 33-volts DC.Product InformationThe Series 65 End-of-Line EOL Relay Base is intended for use with four-wire circuits and features two sets of changeover contacts and a power supervision relay.Key FeaturesDetector locking mechanismOne way fitEasy to wireContains an earth connector

GBP 22.14

1

Apollo Series 65 End-of-Line Relay Base - 24V 45681-248APO

Apollo Series 65 End-of-Line Relay Base 24V - 45681-248OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Options45681-247 for circuits having a supply voltage between 9- and 18-volts DC and 45681-248 for circuits having a supply voltage between 16 and 33 volts DC.Product InformationThe Series 65 End-of-Line EOL Relay Base is intended for use with four-wire circuits and features two sets of changeover contacts and a power supervision relay.Key FeaturesDetector locking mechanismOne way fitEasy to wireContains an earth connector

GBP 22.14

1

Apollo SA6700-100APO Intelligent Twin Switch Monitor

Apollo SA6700-100APO Intelligent Twin Switch MonitorThe Intelligent Twin Switch Monitor provides the functionof two Switch Monitor units within one enclosure. The two units are electrically independent of each other. There is a DILswitch on each unit to set the address.Both Switch Monitor units in the enclosure are designed tomonitor the state of one or more single pole volt-free contactsconnected on a single pair of cables to report the status. Ithas a selectable status reporting delay making it suitable formonitoring flow switches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.ConstructionThe Intelligent Twin Switch Monitor is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsPriority mode for first responseConfigurable input stylesEarth fault monitoring

GBP 65.76

1

Apollo Marine Mini Switch Monitor 55000-775MAR

Apollo Marine Mini Switch Monitor 55000-775MARThe Marine Mini Switch Monitor is a miniature interface with an entirely new housing. The unit is designed to fit into equipment with limited space or mounted within an enclosure such as a manual call point. The interface can also be fitted onto a standard 35mm DIN-Rail using a twist-click motion. The unit is designed to monitor the state of one or more single pole volt-free contacts and reports the contact status to Apollo compatible control panels.OperationThe Marine mini switch monitor features a 20i shortcircuit isolator as standard and can be used as an interrupt or non-interrupt device. The interrupt feature selected via. the DIL Switch means the unit can be used where a priority response is required in particular for monitoring an individual or a zone of conventional manual call points.Please note When the eighth section of the DIL switch is changed the mini switch monitor will change the type code it sends to the panel. The panel will have to be programmed to accept this change.Key FeaturesDesigned for use where space is limitedIsolated as standardInterruptnon interrupt in one unitPre-alarm status availableThree coloured LEDs giving clear status indication

GBP 61.01

1

Apollo Series 65 Relay Base 12v 45681-508APO

Apollo Series 65 Relay Base 12v 45681-508The Series 65 12V Relay Base is designed for use in both fire and security systems. For fire systems a jumper on the PCB is fitted to a latching position. For security systems the jumper is moved to another position so that the base is non-latching.OperationSeries 65 Relay Bases are primarily intended for use with control units using 4-wire detector supply and alarm initiating circuits. Where local codes allow they may also be used in 2 and 4-wire circuits to provide volt-free control signals to an auxiliary system such as an automatic door closer. They are not suitable for use in systems where it is specified or required that operation of the auxiliary system shall be fail-safe and must not be used with any other type of detector.Mechanical ConstructionThe base is a white self-extinguishing polycarbonate moulding with zero-force nickel-plated steel terminals for attaching the detector. The moulding has an aperture to accept the locking grub screw built into the detector case. All electronic components including the relay are mounted on a PCB which is retained by two screws in the moulding.Product InformationThe Series 65 12V Relay Base is designed for use in both fire and security systems. For fire systems a jumper on the PCB is fitted to a latching position. For security systems the jumper is moved to another position so that the base is non-latching.Key FeaturesDetector locking mechanismOne-way fitEasy to wireContains an earth connectorCan be used in fire and security systems

GBP 9.76

1

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light.The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode.If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate.To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation.The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 16.52

1

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light. The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode. If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate. To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation. The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 19.98

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)

Apollo Series 65 Auxiliary Relay Base 45681-246APO

Apollo Series 65 Standard Relay Base 45681-245APO

Apollo Orbis Conventional Duct Smoke Detector - 53546-023APO

Apollo Series 65 Conventional Duct Smoke Detector - 53546-021APO

Apollo Dual Switch Manual Call Point SA5900-011APO

Apollo SA4700-302APO Intelligent DIN-Rail Input Output Unit

Apollo SA4700-300APO Intelligent DIN-Rail Switch Monitor

Apollo Series 65 BR Heat Detector - 55000-127APO

Apollo Series 65 CS Heat Detector - 55000-137APO

Apollo Series 65 CR Heat Detector - 55000-132APO

Apollo Series 65 A1R Heat Detector - 55000-122APO

Apollo SA4700-100APO Intelligent Switch Monitor

Apollo XP95 Mini Switch Monitor - 55000-760APO

Apollo Marine DIN-Rail Switch Monitor Plus 55000-772MAR

Apollo SA4700-104APO Intelligent Twin Input Output Unit

Apollo Series 65 End-of-Line Relay Base 12V - 45681-247APO

Apollo Series 65 End-of-Line Relay Base - 24V 45681-248APO

Apollo SA6700-100APO Intelligent Twin Switch Monitor

Apollo Marine Mini Switch Monitor 55000-775MAR

Apollo Series 65 Relay Base 12v 45681-508APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Powered by Cobiro