Advanced ExGo 8 Way Relay Output Card - EXP-008 Advanced ExGo 8 Way Relay Output Card - EXP-008The 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs.The 2 or 8 Way Relay Output Card connects directly to thepanels motherboard in which each outputcan be individually programmed.Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 or 8 individual programmable outputsEach output individually programmableFast responseEach output 30V ACDC 1 Amp ratingCost effective against ancillary hardwareOptional fail-safe setupEasily programmable by on board keypadPlease Note This is to be used with theAdvanced EX-3001 ExGo Three Zone Automatic Gas Extinguishing Panel only. GBP 258.78 1
Advanced ExGo 8-Way Relay Output Card for use with EX-3001 only Fitted EXP-008F 8-Way Relay Output Card for use with EX-3001 only Fitted EXP-008FThe 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs.The 2 or 8 Way Relay Output Card connects directly to thepanels motherboard in which each outputcan be individually programmed.Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 or 8 individual programmable outputsEach output individually programmableFast responseEach output 30V ACDC 1 Amp ratingCost effective against ancillary hardwareOptional fail-safe setupEasily programmable by on board keypadPlease Note This is to be used with theAdvancedEX-3001ExGo Three Zone Automatic Gas Extinguishing Panel only. GBP 258.78 1
Advanced RLEDNM3PHO Mor-LED IP65 High Output Bulkhead Surface Mount Non-Maintained Addressable Advanced RLEDNM3PHO Mor-LED IP65 High Output Bulkhead Surface Mount Non-Maintained AddressableThe Mor-LED High Output bulkhead is a robust IP65-rated polycarbonate base and polycarbonate fresnel lens. Mor-LED High Output luminaires provide 800 lumen output as standard with the fresnel lens creating cost effective opportunities to minimise the number of luminaires required within an installation.Mor-LED luminaires can be surface mounted or semi-recessed and are ideal for exterior and industrial applications where higher illuminance levels are required.The luminaire provides 800 lumens and the lens generates a wide intensity distribution ideal for providing good luminance on an escape route. The Mor-LED fully supports all features of the LuxIntelligent test system and complies fully with all the relevant requirements of EN60598.2.22.OperationThe Mor-LED is supplied with integral maintained emergency lighting control gear. The non-maintained operation is achieved by excluding the switched live supply. The self-contained variants offer 3-hour emergency lighting duration from integral nickel cadmium batteries. The luminaires can be used for standard switched mains lighting but will automatically provide emergency lighting in the event of a loss of local mains supply. They are ideal for low-maintenance applications offering 4 to 5 years of maintenance-free operation and provide an excellent solution to anywhere with a high lux requirement such as 50 lux in an emergency in a treatment room.Key Features Fully compatible with LuxIntelligent test system High output 800 Lumens Long-life LEDs 50000 hours IP65-rated bulkhead Low power consumption Suitable for use in cold stores down to -20C Fully complies with all aspects of EN60598.2.22 Lens can be fitted with 100mm high self-adhesive signs Suitable for 50 lux minimum requirements like treatment rooms GBP 320.03 1
Advanced LLED3NM3 PSURHL LED-Lite High Output Downlighter Surface Mount Addressable Non-Maintained Advanced LLED3NM3PSURHL LED-Lite High Output Downlighter Surface Mount Addressable Non-MaintainedThe LED-Lite range of surface mount luminaires offers a simple method of providing discrete emergency lighting in areas that require a robust surface-mounted self-contained solution.Available with a symmetrical wide-angle lens or an asymmetrical corridor lens for escape routes or as a 20 degree high-level beam version for highlighting key areas the luminaire simply requires a permanent 230 Volt supply and addressable wiring to provide effective non-maintained emergency lighting with a 3-hour duration. The LED-Lite fully supports all features of the LuxIntelligent test system. IP65 weatherproof versions also available for outside usage.OperationThe LED-Lite is supplied with integral non-maintained emergency lighting control gear. The self-contained unit offers 3-hour emergency lighting duration from integral nickel-metal hydride batteries. The LED-Lite incorporates a high brightness green LED into the white polycarbonate bezel to provide battery charge indication. The luminaires will automatically provide emergency lighting in the event of a loss of local mains supply. The benefits of modern LEDs are well documented.InstallationThe LED-Lite units have a BESA rear entry and 20mm knock-outs for surface conduit entry. When the corridor lens is specified the LED can easily be rotated to align the distribution along the escape route. GBP 398.18 1
Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card Fitted Advanced MxPro MXP-035F Peripheral Bus - 4-Way Relay Card FittedThe Programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits.Up to 16 cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs.Each output is fully programmable using the powerful dynamic cause-and-effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Applications Limitations Plant control and signalling outputs. Each output can be assigned to an individual output group and is fully programmable for any output function allowed within the MxPro 4 configuration program.Fitting of the Programmable 4-Way Relay Cardin a panel precludes fitting of other panel option cards. Requires installation of the Peripheral Bus Interface Card in the panel when using the MxPro 4 series.Key FeaturesEach output is 230V 5A ratedEach output is individually programmable with any of the available DynamiX cause-and-effect rulesUp to 16 cards can be connected providing a total of 64 additional outputsEach output may be individually programmedAn input is provided to monitor the fault output from a power supply.4-way programmable relay cardEasily configured via PC-NET-0033-year warranty as standard GBP 279.74 1
Advanced MXP-034 Peripheral Bus - 4-Way Sounder Card Advanced MXP-034 Peripheral Bus - 4-Way Sounder CardThe Programmable 4-Way Sounder Card is an optional peripheral unit that provides four individually programmable and monitored sounder output circuits compliant with BSEN54-2 1998 Clause 7.8.Up to 16 Cards can be connected to a multi-loop panel providing a maximum of 64 additional local sounder outputs.Each output is fully programmable using the powerful DynamiX Cause and Effect rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 4A power supply.Key Features4 Way Programmable Sounder Card16 cards max per Control panel totalling 64 1 Amp rated outputsEasily configured via PC-NET-0033 Year Warranty as standardFully SynchronisedEach output is 1A rated and monitored for open and short circuitsEach output is individually programmable using the Dynamix cause-and-effects rulesAll outputs can be synchronised in pulsing modesUp to 16 cards can be connected giving a total of 64 additional outputsEach output may be individually programmed GBP 314.51 1
Advanced MxPro MXP-034F Peripheral Bus - 4-Way Sounder Card Fitted Advanced MxPro MXP-034F Peripheral Bus - 4-Way Sounder Card FittedThe Programmable 4-Way Sounder Card is an optional peripheral unit that provides four individually programmable and monitored sounder output circuits compliant with BSEN54-2 1998 Clause 7.8.Up to 16 cards can be connected to a multi-loop panel providing a maximum of 64 additional local sounder outputs.Each output is fully programmable using the powerful dynamic cause-and-effect rules and all outputs are synchronised.The unit is available as either a printed circuit card only or as a boxed version with integral 4A power supply.Applications LimitationsEN54-2 compliant sounder outputs. Can be used with MxPro 4 2 4 8 loop control panels programmed with version 020-02 software or later and fitted with base card hardware revision levels 10 712-1022 MxPro 5 4 loop and 09 712-1022-002 MxPro 5 2 loop or later.Requires installation of the Peripheral Bus Interface Adaptor card in the panel when using the MxPro 4 series.Key FeaturesEach output is 1A rated and monitored for open and short circuits.Each output is individually programmable using the Dynamix cause-and-effects rules.All outputs can be synchronised in pulsing modes.Up to 16 cards can be connected giving a total of 64 additional outputs.Each output may be individually programmedEasily configured via PC-NET-0033-year warranty as standard GBP 314.51 1
Advanced Programmable Relay - MXP-035 Advanced Programmable Relay - MXP-035The programmable 4-Way Relay Card is an optional peripheral unit that provides four individually programmable relay output circuits. Up to 16 Cards can be connected to a multi-loop control panel providing a maximum of up to 64 additional local relay outputs. Each output is fully programmable using the powerful DynamiX cause and effects rules and all outputs are synchronised. The unit is available as either a printed circuit card only or as a boxed version with integral 1A power supply.Key Features4 Way Programmable Relay Card16 Cards Max per Control panel totalling 64 230V 5 Amp rated outputsEasily Configured via PC-NET-0033 Year Warranty as standard GBP 279.74 1
Advanced MXP-650 2.5A 24V EN54-4 PSE amp Battery Charger - Large Up To 2x 17Ah Batteries Advanced MXP-650 2.5A 24V EN54-4 PSE Battery Charger - Large Up To 2x 17Ah BatteriesThe Advanced MXP-650 is a 2.5A power supply unit which can be used for any fire alarm system including AOV systems. They are certified to EN54-4 by VdS and EN12101-10 by AFNOR ensuring reliable and safe operation.Suited for almost any application the power supply unit and battery charger have been developed using the latest technology to provide a high-efficiency switch-mode power supply.The units include intelligent battery charging technology mains and battery monitoring including two independent volt-free outputs. In addition they also provide deep battery discharge protection in case of a prolonged mains failure.The inclusion of LED indicators provides quick status diagnostics of the power supply.These power supply units compliment the MXP-549 1.5A model.Key Features2.5A outputHousing fits 2 x 17Ah batteriesA range of power supply equipment with power output options to suit most applicationsUniversal AC inputIndependently monitored dual outputs of 27.6VdcHigh-efficiency switched mode power suppliesAlternative enclosure sizes to support standby battery backup optionsExterior status LEDs to support diagnosticsLoad-sharing supporting either rapid charging or brief high-current peak-loadsNo output interruption during automatic switchover between mains and battery powerDeep discharge protection disconnects battery from load when output voltage falls below 21.6VSelf-resetting battery fuse protection GBP 263.58 1
Advanced MXP-650D 2.5A 24V EN54-4 PSE amp Battery Charger - Deep Up to 2x 24Ah or 38Ah Batteries Advanced MXP-650D 2.5A 24V EN54-4 PSE Battery Charger - Deep Up to 2x 24Ah or 38Ah BatteriesThe Advanced MXP-650 is a 2.5A power supply unit which can be used for any fire alarm system including AOV systems. They are certified to EN54-4 by VdS and EN12101-10 by AFNOR ensuring reliable and safe operation.Suited for almost any application the power supply unit and battery charger have been developed using the latest technology to provide a high-efficiency switch-mode power supply.The units include intelligent battery charging technology mains and battery monitoring including two independent volt-free outputs. In addition they also provide deep battery discharge protection in case of a prolonged mains failure.The inclusion of LED indicators provides quick status diagnostics of the power supply.These power supply units compliment the MXP-549 1.5A model.Key Features2.5A outputHousing fits 2x 24Ah or 38Ah batteriesA range of power supply equipment with power output options to suit most applicationsUniversal AC inputIndependently monitored dual outputs of 27.6VdcHigh-efficiency switched mode power suppliesAlternative enclosure sizes to support standby battery backup optionsExterior status LEDs to support diagnosticsLoad-sharing supporting either rapid charging or brief high-current peak-loadsNo output interruption during automatic switchover between mains and battery powerDeep discharge protection disconnects battery from load when output voltage falls below 21.6VSelf-resetting battery fuse protectionThe image is for illustrative purposes only. GBP 313.84 1
Advanced RLED230 Mor-LED Mains Only Bulkhead Advanced RLED230 Mor-LED Mains Only BulkheadThe Mor-LED bulkhead is a robust IP65-rated polycarbonate base combined with a clear fresnel lens housing 16 high-output white LEDs and a constant current maintained drive circuit. The luminaire provides 90 lumens and the lens generates a wide intensity distribution ideal for providing good luminance on an escape route. We are also able to offer a High Output variant that produces 800 lumens suitable for areas such as treatment rooms. A deep 150mm opal diffuser is available to provide double-sided signage if required. The Mor-LED fully supports all features of the LuxIntelligent test system and complies fully with all the relevant requirements of EN60598.2.22.Operation The Mor-LED is supplied with integral maintained emergency lighting control gear. The non-maintained operation is achieved by excluding the switched live supply. The self-contained variants offer 3-hour emergency lighting duration from integral nickel cadmium batteries. The luminaires can be used for standard switched mains lighting but will automatically provide emergency lighting in the event of a loss of local mains supply. The benefits of modern LEDs are well documented. They are very energy efficient and offer very long life typically over 50000 hours. They also operate at low temperatures no cold starting problems and do not create higher internal temperatures thereby improving the life of the internal batteries as well as making them more suitable for use in cold store environments. They are ideal for low-maintenance applications offering 4 to 5 years of maintenance-free operation.Installation20mm drilling points are available at either end of the base as well as one on the rear.Key FeaturesFully compatible with LuxIntelligent test systemLong-life LEDs 50000 hoursIP65-rated bulkheadLow power consumption less than 10WSuitable for use in cold stores down to -20CFully complies with all aspects of EN60598.2.22Lens can be fitted with 100mm high self-adhesive signs90 Lumens output as standardHigh output 800 Lumens variant available GBP 225.77 1
Advanced RLED230P Mor-LED Slave Addressable Bulkhead Advanced RLED230P Mor-LED Slave Addressable BulkheadThe Mor-LED bulkhead is a robust IP65-rated polycarbonate base combined with a clear fresnel lens housing 16 high-output white LEDs and a constant current maintained drive circuit. The luminaire provides 90 lumens and the lens generates a wide intensity distribution ideal for providing good luminance on an escape route. We are also able to offer a High Output variant that produces 800 lumens suitable for areas such as treatment rooms. A deep 150mm opal diffuser is available to provide double-sided signage if required. The Mor-LED fully supports all features of the LuxIntelligent test system and complies fully with all the relevant requirements of EN60598.2.22.Operation The Mor-LED is supplied with integral maintained emergency lighting control gear. The non-maintained operation is achieved by excluding the switched live supply. The self-contained variants offer 3-hour emergency lighting duration from integral nickel cadmium batteries. The luminaires can be used for standard switched mains lighting but will automatically provide emergency lighting in the event of a loss of local mains supply. The benefits of modern LEDs are well documented. They are very energy efficient and offer very long life typically over 50000 hours. They also operate at low temperatures no cold starting problems and do not create higher internal temperatures thereby improving the life of the internal batteries as well as making them more suitable for use in cold store environments. They are ideal for low-maintenance applications offering 4 to 5 years of maintenance-free operation.Installation20mm drilling points are available at either end of the base as well as one on the rear.Key FeaturesFully compatible with LuxIntelligent test systemLong-life LEDs 50000 hoursIP65-rated bulkheadLow power consumption less than 10WSuitable for use in cold stores down to -20CFully complies with all aspects of EN60598.2.22Lens can be fitted with 100mm high self-adhesive signs90 Lumens output as standardHigh output 800 Lumens variant available GBP 241.90 1
Advanced MxPro 5 MXP-538 P-BUS 16-Way Switch Form Factor Module Advanced MxPro 5 MXP-538 P-BUS 16-Way Switch Form Factor ModuleThe 16-way Switch 48 LED Card is an expansion peripheral that offers 16 inputs and 48 outputs that can be configured via the Advanced PC Config Tool. This additional PCB provides a cost effective solution to providing 16 individually programmable push buttons for controlling fire alarm equipment.Up to 16 cards can be connected to a MxPro 5 series panel providing a maximum of 256 push buttons and 768 LED outputs. Each LED output can be individually assigned to an output group to provide full support for dynamic zoning and to indicate when the buttons have been activated.ApplicationsIdeal for any application where a number of programmable push button switches are required for evacuation and plant control.Key Features16 configurable push buttons48 Programmable LEDs 3 x LEDs per push button red green yellowConfigurable buzzerFast input responseUp to 16 switch plates for each control panel GBP 374.58 1
Advanced MxPro 5 MXP-539 P-BUS Mimic Driver Card 16 Inputs amp 48 Outputs Advanced MxPro 5 MXP-539 P-BUS Mimic Driver Card 16 Inputs 48 OutputsThe 16-way Switch 48 LED Card is an expansion peripheral that offers 16 inputs and 48 outputs that can be configured via the Advanced PC Config Tool. This additional PCB provides a cost effective solution to providing 16 individually programmable push buttons for controlling fire alarm equipment.Up to 16 cards can be connected to an MxPro 5 series panel providing a maximum of 256 push buttons and 768 LED outputs. Each LED output can be individually assigned to an output group to provide full support for dynamic zoning and to indicate when the buttons have been activated.ApplicationsIdeal for any application where a number of programmable push button switches are required for evacuation and plant control.Key Features6 configurable clean-contact inputs48 programmable LED driver outputsConfigurable buzzerFast input responseUp to 16 switch plates for each control panelNo network interface required GBP 330.30 1
Advanced Lux Intelligent ULEDM3PMW Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead with Microwave Detect Advanced Lux Intelligent ULEDM3PMW Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead with Microwave DetectThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22 GBP 397.04 1
Advanced Lux Intelligent ULEDM3PDALI Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead Advanced Lux Intelligent ULEDM3PDALI Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead The Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Comes with DALI dimming control GBP 344.81 1
Advanced Lux Intelligent ULEDM3PSLDIM Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead Advanced Lux Intelligent ULEDM3PSLDIM Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead The Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Comes with 1-10V Dimming Control and silver body GBP 344.81 1
Advanced Lux Intelligent ULEDM3PSL Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead and Silver Body Advanced Lux Intelligent ULEDM3PSL Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead and Silver BodyThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22 GBP 287.36 1
Advanced Lux Intelligent ULEDM3P Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead Advanced Lux Intelligent ULEDM3P Circu-LED LED 3Hr Maintained Emergency Addressable Circular BulkheadThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provides 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22 GBP 287.36 1
Advanced Lux Intelligent ULEDM3PDIM Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead Advanced Lux Intelligent ULEDM3PDIM Circu-LED LED 3Hr Maintained Emergency Addressable Circular Bulkhead The Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Comes with 1-10V Dimming Control GBP 344.81 1
Advanced MXP-651 5.0A 24V EN54-4 PSE amp Battery Charger - Large Up To 2x 17Ah Batteries Advanced MXP-651 5.0A 24V EN54-4 PSE Battery Charger -Large Up To 2x 17Ah BatteriesThe Advanced MXP-650 2.5A and MXP-651 5.0A power supplyunits can be used for any fire alarm system including AOV systems. They arecertified to EN54-4 by VdS and EN12101-10 by AFNOR ensuring reliable and safeoperation. Suited for almost any application the power supply unit and batterycharger have been developed using the latest technology to provide ahigh-efficiency switch-mode power supply.The units include intelligent battery charging technologymains and battery monitoring including two independent volt-free outputs. Inaddition they also provide deep battery discharge protection in case of aprolonged mains failure. The inclusion of LED indicators provides quick status diagnosticsof the power supply. These power supply units complement the MXP-549 1.5A.ApplicationsThese power supply units can be used in any fire alarm installationrequiring a 24volt supply for operation and which specifies EN54-4 powersupplies e.g. BS 5839 code of practice EN12101 and AOV systems. Ensuringreliable and safe operation they are certified to EN54-4 and EN12101-10 byAFNOR and VdS EN54-4 only.Key FeaturesA range of power supply equipment with power output options tosuit most applicationsUniversal AC input on the 2.5A and 5.0A versionsIndependently monitored dual outputs of 27.6VdcHigh efficiency switched mode power suppliesAlternative enclosure sizes to support standby batterybackup optionsExterior status LEDs to support diagnosticsLoad-sharing supporting either rapid charging or brief high-currentpeak-loadsNo output interruption during automatic switchover between mainsand battery powerDeep discharge protection disconnects battery from load whenoutput voltage falls below 21.6VSelf-resetting battery fuse protection GBP 412.88 1
Advanced Lux Intelligent ULED230SLDIM Circu-LED LED Mains Only Circular Bulkhead Advanced Lux Intelligent ULED230SLDIM Circu-LED LED Mains Only Circular Bulkhead comes with 1-10V Dimming Control and Silver BodyThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting. GBP 180.23 1
Advanced Lux Intelligent ULED18M3P Circu-LED LED 18W 3Hr Maintained Emergency Addressable Circular Bulkhead Advanced Lux Intelligent ULED18M3P Circu-LED LED 18W 3Hr Maintained Emergency Addressable Circular Bulkhead 0.33M DiameterThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provides 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting the 230v Mains Only product are not emergency lights and should not be used as one. The product is only for use as a standard light fitting. GBP 266.43 1
Advanced Lux Intelligent ULED230DIM Circu-LED LED Mains Only Circular Bulkhead cw 1-10V Dimming Control Advanced Lux Intelligent ULED230DIM Circu-LED LED Mains Only Circular Bulkhead comes with 1-10V Dimming ControlThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting. GBP 180.23 1
Advanced Lux Intelligent ULED18230P Circu-LED 18W LED Slave Addressable Circular Bulkhead Advanced Lux Intelligent ULED18230P Circu-LED 18W LED Mains only Slave Addressable Circular Bulkhead 0.33M DiameterThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provides 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting the 230v Mains Only product are not emergency lights and should not be used as one. The product is only for use as a standard light fitting. GBP 181.55 1