mcb.dk | Få success online

Advanced ExGo 2 Way Relay Output Card - EXP-007

Advanced ExGo 2 Way Relay Output Card - EXP-007The 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs. The 2 or 8 Way Relay Output Card connects directly to the panels motherboard in which each output can be individually programmed. Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 Individual Programmable OutputsFast Instant ResponseEach Output 30V ACDC 1 Amp RatingCost effective against ancillary hardware

GBP 120.76

1

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail Carrier

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail CarrierThe Peripheral Relay Card provides 10 30V DC 1A programmable relay outputs.The Peripheral Relay Card connects directly to any of the DIL connectors of either the Network Mimic 100 LED Output Card or the Multi way InputOutput Card unit via the supplied ribbon cable.Each output follows the cause-and-effect programming of the mimic unit output.This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the MxPro5 Dynamic zoning facilities.Key FeaturesTen change-over contacts outputs at 30Vdc 1ADIN rail fixingSeparate isolate input disables all outputsSeparate isolate indication outputFast response

GBP 149.43

1

Advanced 20-VMC100-ADV Single Relay Powered Output Module With Built In Isolator

Advanced 20-VMC100-ADV Single Relay Powered Output Module With Built In IsolatorThe single output module is loop powered designed around a fully digital protocol and provides control by activating equipment for DDA compliance such as vibrating pillows. The output channel is monitored and will detect open and short circuit conditions.The unit provides a fast and secure response and incorporates a bidirectional short circuit isolator. Connections are made using plug-in terminal blocks which will accept conductors up to 2.5mm.The unit is supplied fixed to a plate which is suitable for wall mounting. Standard 25mm or deep 47mm mounting boxes are available.Key FeaturesShort circuit isolators in each device to the requirements of EN54- 17Auto addressing capability by the control panel or manually using a handheld programmerDigital checking of double addressLine quality informationBicolour red green LED driven by the control panel

GBP 131.62

1

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052The Mxp-052 is a peripheral relay card providing ten 30V DC 1A programmable relay outputs. The Mxp-052 connects directly to any of the DIL connectors of either the Network Mimic Mxp-020-100 LED Output Card or the General IO controller Mxp-045 LED Output Card units via the supplied ribbon cable.Each output follows the cause and effect programming of the mimic unit output. This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the Mx-40005000 systems Dynamix zoning facilities.Key FeaturesTen change-over contact outputs rated at 30V DC 1A.Up to 200 individual relay outputs fully programmable per mimic excluding LEDsTen individually programmable relay outputs per unitDIN rail or screw fixing optionsSeparate isolate input disables all outputsSeparate isolate indication outputFast instant responseProduct CodesDescriptionMXP-052Mimic driven 10-way relay output cardMXP-052-DINMimic driven 10-way relay output card in din-rail carrier

GBP 129.16

1

Advanced MXP-507 2-Way Relay Card MxPro 5

Advanced MXP-507 2-Way Relay Card MxPro 5The 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3 year warranty as standard

GBP 118.54

1

Advanced MxPro 5 MXP-507F 2-Way Relay Card Fitted

Advanced MxPro 5 MXP-507F 2-Way Relay Card FittedThe 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3-year warranty as standard

GBP 118.54

1

Advanced Sounder Booster Card - MXS-025

Advanced Sounder Booster Card MXS-025The Sounder Booster Card is a peripheral unit that utilises a standard sounder circuit panel or loop driven and provides increased sounder output capability.This boosted output is fully monitored for open and short circuits and will take an independent supply to provide up to 4A of sounder current to a single circuit.On-board indication via 2 LED indicators located on the booster PCB enable the user to view when an output has been triggered and when an external power supply has been connected.Applications LimitationsThe sounder booster is used where a single sounder output circuit of up to 4A is required.Each of the panels sounder outputs can only monitor a single circuit. The unit must therefore be situated at the end of the panels sounder output circuit to maintain correct fault monitoring.Key FeaturesIncreased sounder capability up to 4AOn-board indicationPSU fault input contactsCost effective against ancillary hardware3 year warranty as standardCompatibilityThe Sounder Booster Cardis compatible with allMxPro 5controlpanels.

GBP 122.83

1

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021The Mxs-021 Sounder Circuit Splitter is a peripheral unit for use with all MxPro4 range of control Panels. This additional unit takes a standard sounder circuit from either a control panel or other panel based sounder circuit controller and multiplies to provide up to 4 monitored outputs. In operation the additional outputs follow the output they are connected to. The circuits are fully monitored for open and short circuit and will take an independent supply to provide up to 1A per circuit.Key Features4 Monitored Outputs3 Year Warranty as standardUp to 1 Amp per circuitCost effective against ancillary hardwareCompatibilityThe Sounder Splitter Cardis compatible with all MxPro 4 controlpanels.LimitationsThe 4-way sounder splitter card can be supplied as a PCB only for mounting. When supplied fitted in this format the load at the outputs from the splitter will be limited to the sounder output loading of the input circuit from which it is driven.All 4 outputs on the sounder splitter card will operate in tandem and follow the output of the sounder circuit to which the card is connected.

GBP 163.18

1

Advanced MXP-049 1.5A EN54-4 PSU amp Charger Utility Enc. - 7Ah battery capacity

Advanced MXP-049 1.5A EN54-4 PSU Charger Utility Enclosure - 7Ah battery capacityThe Advanced 1.5A 3.0A and 5.0A Power Supply Units can be used for any fire alarm system installation that specifies EN54-4 Power Supply Equipment.Suited for almost any application except for CIE in separate cabinet the power supply unitbattery charger has been developed using the latest surface mount technology to provide a high efficiency switch mode power supply.The power supply units are available in fully enclosed construction providing power and fault indication or alternatively in caged versions for mounting into existing enclosures of various sizes to suit different battery capacities.Key FeaturesA range of power supply equipment with power output options to suit most applicationsAll models monitor the battery internal series resistanceIP30 Steel Enclosure

GBP 173.37

1

Advanced Lux Intelligent ULED230SL Circu-LED LED Mains Only Circular Bulkhead and Silver Body

Advanced Lux Intelligent ULED230SL Circu-LED LED Mains Only Circular Bulkhead and Silver BodyThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting.

GBP 138.45

1

Advanced Lux Intelligent ULED230 Circu-LED LED Mains Only Circular Bulkhead

Advanced Lux Intelligent ULED230 Circu-LED LED Mains Only Circular BulkheadThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provide 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting this product is not an emergency light and should not be used as one. The product is only for use as a standard light fitting.

GBP 138.45

1

Advanced Lux Intelligent ULED18230 Circu-18W LED Mains Only Circular Bulkhead

Advanced Lux Intelligent ULED18230 Circu-18W LED Mains Only Circular BulkheadThe Circu-LED offers a decorative surface mounted circular luminaire incorporating high output white LEDs providing ultra-long life and low power consumption. The LED luminaires utilise an aluminium base white as standard and a twist on fire-retardant PMMA diffuser. The luminaire has a huge 1550 lumens output and is not prone to the issues often prevalent in the 28W T5 counterpart fittings. This makes it an ideal replacement for such areas as stairwells where building owners may wish to use motion detectors to cut down on unnecessary lighting for areas not permanently occupied.The Circu-LED luminaire range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per watt.OperationThe range can be supplied as mains only or maintained emergency versions. Both versions are available with 1-10V dimming control as an option. All emergency versions provides 3 hour duration from integral high temperature nickel cadmium batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency power in the event of loss of the local mains supply.Key FeaturesDecorative circular LED LuminaireFully Lux Intelligent compatibleLong life LEDs 50000 hoursLow power consumptionStandard and dimmable versions availableFully complies with all aspects of EN60598.2.22Please Note although listed under Emergency Lighting the 230v Mains Only product are not emergency lights and should not be used as one. The product is only for use as a standard light fitting.

GBP 100.55

1

Advanced MxPro 5 MXP-541V-002 AlarmCalm Button with Buzzer Argus Vega Protocol

Advanced MxPro 5 MXP-541V-002 AlarmCalm Button with Buzzer Argus Vega ProtocolAlarmCalm is Advanceds complete False Alarm Management FAM solution. AlarmCalm comprises Advanceds MxPro 5 or Axis EN fire systems new AlarmCalm config software and our intelligent loop powered AlarmCalm buttons. Among many features AlarmCalm allows the initial activation of a fire detector to be accepted and dealt with in a localised area of the protected premises. i.e. an AlarmCalm Button located inside dwellingapartment can used be for silencing unwanted alarms when there is a local fire condition.When used in conjunction with the AlarmCalm software it can be used to help verify if an activated condition from a device is considered to be a genuine alarm before the fire alarm condition is displayed on the panel. The AlarmCalm button is a dedicated module connecting to an Apollo or Argus protocol detection loop on our MxPro 5 multiprotocol panel.Key FeaturesPush button inputLED output for use as pollingactivated functionMechanically compatible with a single gang UK electrical back boxFully addressable device address sits on loop Apollo 1-126 Axis EN1-240Fully programmable using AlarmCalm software including verification and second-stage timesUnique device type recognised as AlarmCalm unit by MxPro 5 FACPsWiring terminations suitable for all Advanced recommended loop cablesOptional programmable audible buzzer outputAimed at reducing unwanted alarms

GBP 95.77

1

Advanced MxPro 5 MXP-541A-002 AlarmCalm Button with Buzzer Apollo Protocol

Advanced MxPro 5 MXP-541A-002 AlarmCalm Button with Buzzer Apollo ProtocolAlarmCalm is Advanceds complete False Alarm Management FAM solution. AlarmCalm comprises Advanceds MxPro 5 or Axis EN fire systems new AlarmCalm config software and our intelligent loop powered AlarmCalm buttons. Among many features AlarmCalm allows the initial activation of a fire detector to be accepted and dealt with in a localised area of the protected premises. i.e. an AlarmCalm Button located inside dwellingapartment can used be for silencing unwanted alarms when there is a local fire condition.When used in conjunction with the AlarmCalm software it can be used to help verify if an activated condition from a device is considered to be a genuine alarm before the fire alarm condition is displayed on the panel. The AlarmCalm button is a dedicated module connecting to an Apollo or Argus protocol detection loop on our MxPro 5 multiprotocol panel.Key FeaturesPush button inputLED output for use as pollingactivated functionMechanically compatible with a single gang UK electrical back boxFully addressable device address sits on loop Apollo 1-126 Axis EN1-240Fully programmable using AlarmCalm software including verification and second-stage timesUnique device type recognised as AlarmCalm unit by MxPro 5 FACPsWiring terminations suitable for all Advanced recommended loop cablesOptional programmable audible buzzer outputAimed at reducing unwanted alarms

GBP 93.01

1

Advanced Lux Intelligent RNLEDAC Round-LED Mains Only Luminaire

Advanced Lux Intelligent RNLEDAC Round-LED Mains Only LuminaireThe Round-LED range provides both mains and emergency lighting from a well-designed luminaire with a white polycarbonate base and opal polycarbonate diffuser sealed to IP65 making it suitable for both interior and external applications. The luminaire has a unique lever to release the diffuser which can be secured with the supplied locking screw to increase tampervandal resistance. Internally the removable steel gear tray has 54 white high output long life LEDs mounted upon it reveals access to the control gear and terminal blocks.The Round-LED range supports all the features of the Lux Intelligent range of emergency lighting test panels and also fully complies with the requirements of EN60598.2.22. It also meets with the current Part L energy targets offering over 60 lumens per Watt.OperationThe luminaire can be supplied in both mains only or maintained emergency versions non-maintained can be achieved by excluding the normal switched mains live supply. Both versions can be supplied with dimming control as well microwave presence detectors. All emergency versions provide 3-hour duration from the integral high temperature NiMH batteries. Maintained versions can be used for standard switched mains lighting but will automatically provide emergency lighting in the event of a complete loss of local mains supply.InstallationThe luminaire has 20mm drilling points on the base for cable entryKey FeaturesVersatile circular LED luminaireLong life LEDs 50000 hoursFully Lux Intelligent compatibleLow power consumptionStandard and emergency versions availableIP65 LuminaireFully complies withal aspects of EN60598.2.22

GBP 172.78

1

Advanced ELRL240 Enclosed Hold-Off Relay with Built-In Delay

Advanced ELRL240Enclosed Hold-Off Relay with Built-In DelayOn some installations it can sometimes be more advantageous to provide the emergency lighting from static inverter or central battery system. On systems using static inverters it is sometimes necessary for the normal supply and static inverter supply to be selected automatically by a switching device either within or external to the luminaire. The ELRL240 hold off relay provides a simple solution to this requirement. When a site uses a static inverter it is not always tied to the grid frequency and could even be antiphase with the normal supply. When a relay tries to switch between these supplies there is a tendency for the relay to suffer from arcing between the normally open and normally closed contacts resulting in temporary short circuit between the two out of phase supplies. This will cause external circuit protection to operate. Because the device uses two interposing relays for the two supplies and introduces a time delay of approximately 500mS between breaking the normal supply and connecting the static inverter supply the device removes any risk of arcing across contacts due to phase differences between the two supplies. This is also reversed when the static inverter supply is removed and a similar delay is introduced prior to reconnection to the normal lighting supply.A dimming isolation facility is incorporated as standard for use with dimming ballasts to enable full light output to be achieved in the emergency condition.Key FeaturesEnhanced change-over relay for static inverter supplied luminairesAutomatic time delay to avoid arcing during change-overBuilt in dimming isolation feature

GBP 89.94

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)