167 results (0,18116 seconds)

Brand

Colour

Size

Gender

Merchant

Price (EUR)

Reset filter

Products
From
Shops

CAM CAM COPENHAGEN Luca Book Rack White ONE SIZE

Vivo Cryowrap Cooler Unit

Vivo Cryowrap Cooler Unit

Vivo Cryowrap Cooler Unit ·    Insulated flask for ice/cold water ·    Gravity fed cryotherapy system delivering cold water and support to joints ·    Integrates with compression wraps to reduce swelling around ankles and knees ·    Provides cold and compression therapy to swollen knee and ankle joints ·    Used as part of the PRICE regime. Protect, Rest, Ice, Compression, Elevation ·    The method is widely used in hospitals post-surgery ·    Available to buy with or without knee or ankle sleeves The product consists of cooler, tube and sleeve (sold separately, or as a combination). The cooler is made of urethane foam and high-density polyethylene plastic, the sleeve is made of polyurethane coated nylon. The Vivo-Cryowrap Cooler Unit is intended to be used for cold therapy on specific parts of human body surface. Instructions for use: 1.Prepare cooler: Connect the blue tube to the cooler. Add water to line inside the cooler, then add ice. For 6 to 8 hour treatment, add ice to top of cooler. Lay the insulation disk on top of ice. Attach cooler lid snugly. Allow 5 minutes with occasional shaking to chill water.  2.Apply the empty sleeve: Use a medical isolation pad between your desired area and the sleeve, Position sleeve on the joint with quick-disconnect pointing down. Thread straps through white rings and secure snugly.  3.Fill sleeve: Connect blue tube to sleeve. Open air vent on cooler lid and raise cooler no more than 15.7 inches(40cm) above the sleeve (if the cooler is raised more than 15.7 inches(40cm), the sleeve will increase in volume and weight.) Hold raised cooler for about 30 seconds while sleeve fills. Close air vent on cooler lid. the cooler can now be disconnected from sleeve by pressing the tab on the quick-disconnect while cooler is raised.  4.Rechill water: At first, rechill the water in the sleeve after 15 or 30 minutes, then once an hour or as needed. Reconnect the blue tube to sleeve. lower the cooler below sleeve, and the warmed water will drain from the sleeve into the cooler. Allow a minute or two for the water to mix with the ice and rechill, then raise the cooler and repeat the filling process. Stock Option: Cooler Unit only, Discounted Ankle Cuff & Cryo Unit, Discounted Knee Cuff & Cooler Unit, Knee Cuff Only, Ankle Cuff Only

EUR 104.54
1

Vivo Cryowrap Cooler Unit - 30cm x 13cm - Pack of 40

Vivo Cryowrap Cooler Unit - 30cm x 13cm - Pack of 40

Vivo Cryowrap Cooler Unit ·    Insulated flask for ice/cold water ·    Gravity fed cryotherapy system delivering cold water and support to joints ·    Integrates with compression wraps to reduce swelling around ankles and knees ·    Provides cold and compression therapy to swollen knee and ankle joints ·    Used as part of the PRICE regime. Protect, Rest, Ice, Compression, Elevation ·    The method is widely used in hospitals post-surgery ·    Available to buy with or without knee or ankle sleeves The product consists of cooler, tube and sleeve (sold separately, or as a combination). The cooler is made of urethane foam and high-density polyethylene plastic, the sleeve is made of polyurethane coated nylon. The Vivo-Cryowrap Cooler Unit is intended to be used for cold therapy on specific parts of human body surface. Instructions for use: 1.Prepare cooler: Connect the blue tube to the cooler. Add water to line inside the cooler, then add ice. For 6 to 8 hour treatment, add ice to top of cooler. Lay the insulation disk on top of ice. Attach cooler lid snugly. Allow 5 minutes with occasional shaking to chill water.  2.Apply the empty sleeve: Use a medical isolation pad between your desired area and the sleeve, Position sleeve on the joint with quick-disconnect pointing down. Thread straps through white rings and secure snugly.  3.Fill sleeve: Connect blue tube to sleeve. Open air vent on cooler lid and raise cooler no more than 15.7 inches(40cm) above the sleeve (if the cooler is raised more than 15.7 inches(40cm), the sleeve will increase in volume and weight.) Hold raised cooler for about 30 seconds while sleeve fills. Close air vent on cooler lid. the cooler can now be disconnected from sleeve by pressing the tab on the quick-disconnect while cooler is raised.  4.Rechill water: At first, rechill the water in the sleeve after 15 or 30 minutes, then once an hour or as needed. Reconnect the blue tube to sleeve. lower the cooler below sleeve, and the warmed water will drain from the sleeve into the cooler. Allow a minute or two for the water to mix with the ice and rechill, then raise the cooler and repeat the filling process. Stock Option: Cooler Unit only, Discounted Ankle Cuff & Cryo Unit, Discounted Knee Cuff & Cooler Unit, Knee Cuff Only, Ankle Cuff Only

EUR 104.54
1

Vivo Cryowrap Cooler knee cuff - 30cm x 13cm - Pack of 40

Vivo Cryowrap Cooler ankle cuff - 30cm x 13cm - Pack of 40

Beco Watch winder Boxy Fancy Brick - Brown leather without power supply unit

Beco Watch winder Boxy Fancy Brick - Brown leather without power supply unit

The Beco Boxy Fancy Brick watch winder is the ideal solution for lovers of automatic watches who value functionality and design. The variety of different colors and surface materials ensures that every taste is catered for. The compact device, made of high-quality plastic, not only presents your automatic watch in style, but also ensures its continuous operation through precise winding. Measuring 9.8 x 11 x 13 cm, the watch winder fits seamlessly into any room, even the smallest corners, without sacrificing elegance. The watch is placed securely on a soft cushion designed for bracelet sizes between 16 and 21 cm. A curved, transparent Plexiglas cover protects the watch from dust and dirt and can be easily attached if required. Individual adjustment to the needs of your watch is possible by simply programming the direction of rotation and the number of rotations. The watch winder can be set to between 650 and 3600 rotations per day in 15 stages using sliders on the underside of the device. The direction of rotation (right, left or alternating) can also be selected there. A special feature of the Boxy Fancy Brick series is its modular design, which allows up to three modules to be stacked on top of each other and operated with just one power supply unit. The power supply is ensured by small contacts on the top and bottom of the modules, which makes them easy and efficient to use. For watch enthusiasts who want to expand their collection, the optionally available base plates allow the system to be extended to up to 12 modules. The Beco Boxy Fancy Brick watch winder thus combines modern design with practical functionality and offers an optimal solution for the care and presentation of your automatic watches. Watches, jewelry and other decorative items shown are not included.

EUR 149.00
1