mcb.dk | Få success online

Faithfull Mains Tester Screwdriver - Multi Function

The Faithfull Multi-Tester is more than just a conventional voltage tester. The built-in battery powered sensor allows the multi-tester to perform a number of different functions without the need to dismantle a suspected faulty item or have any contact with live parts. The multi-tester is fully insulated and is supplied complete with full operating instructions and will perform the following tests: continuity, bulbs, fuses, short circuits, cable tracking, mains sockets and microwave oven leakage. SAFETY NOTEAlways read and the instruction supplied with the multi-tester.Never use a multi-tester until you are fully conversant with its use and applications. Never work on live equipment, and if in any doubt, always contact a qualified electrician.

GBP 8.49

1

Faithfull Battery Tester for AA, AAA, C, D & 9V FAIDETBAT

This Faithfull Battery Tester is simple and easy-to-use on most types of standard domestic and rechargeable batteries. It helps to ensure the batteries are fully charged and ready for use. A simple analogue needle display indicates the power level of the batteries (good, low or replacement required). An adjustable arm allows the tester to accommodate the testing of D, C, AA, AAA, 9V 6F22 and 1.5V button cell batteries, and folds down for easy storage. Features Analogue needle indicator. Tests D, C, AA, AAA, 9V 6F22 batteries. Tests 1.5V button cell batteries. NOTE The tester is activated by the battery being checked. Keep test time as short as possible to avoid unnecessary battery drain.

GBP 7.59

1

Faithfull Socket Polarity Tester with RCD Test Function FAIDETSOCRCD

The Faithfull Socket Tester is an essential mains safety tester designed for testing socket wiring and RCDs. It will determine whether a socket is wired correctly or incorrectly. Used in conjunction with the coding table provided, the 5 combined indicators show the true status of the sockets wiring condition. It provides a true ground error indication through the LCD if dangerous contact voltage is present at the protective earth (PE). The use of 3 neon indicators for L-N-PE provides rapid detection of correct/incorrect socket wiring. It is equipped with an additional RCD tester for testing the operation of RCDs with a rating of not more than 30mA. Specification Socket Type UK 240V 3-Pin Nominal Voltage 220V & plusmn10% Frequency Range 5060Hz Measurement Category CATIII, 300V RCD Test Time 60300ms Contact Voltage Threshold & lt35 AC against ground depending on coupling to earth RCD Test Current 30mA & plusmn15% Dimensions 77 x 67 x 66mm Weight approx. 70g

GBP 21.99

1

Faithfull Socket Polarity Tester FAIDETSOC

The Faithfull Socket Polarity Tester tests sockets quickly and easily. It can be used to determine whether socket wiring is correct or incorrect. Used in conjunction with the coding table provided, the 3 combined lamps indicate the state of the socket's wiring condition. The compact and durable design is easy to operate and read. Just plug into a socket for automatic detection. Specification Socket Type UK 240V 3-Pin Nominal Voltage 240V Frequency Range 5060Hz Operating Temperature 0C to 40C Dimensions 71 x 62 x 62mm Weight approx. 63g

GBP 13.99

1

Faithfull Mains Tester Screwdriver, Long

Made from virtually unbreakable and shatterproof ABS. The handle, pocket clip and blade are insulated for maximum safety. Made to VDE specification 0680- Part 6 - 4.77 To test the circuit place the end on the electric contact and press your thumb against the metal contact next to the neon viewing window, if the contact is live the bulb will light. IMPORTANT:-Check that the neon bulb is in order by using the tester first on a known live circuit.Never touch the uninsulated part of the blade when testing.

GBP 6.19

1

Faithfull Mains Tester Screwdriver FAIMTS

Made from virtually unbreakable and shatterproof ABS. The handle, pocket clip and blade are insulated for maximum safety. Made to VDE specification 0680- Part 6 - 4.77 To test the circuit place the end on the electric contact and press your thumb against the metal contact next to the neon viewing window, if the contact is live the bulb will light. IMPORTANT:-Check that the neon bulb is in order by using the tester first on a known live circuit.Never touch the uninsulated part of the blade when testing.

GBP 5.69

1

Faithfull Voltage Detector Pen 50-1000V ac

This Faithfull Voltage Detector is a handy instrument that uses a safe, non-contact method to detect AC voltage in outlets, lighting fixtures, circuit breakers, wires and cables and can be used to find circuit breaks in a wire. A voltage test is easy to carry out by simply holding the detector by its body and placing the white end cap near or onto a cable or fitting believed to be carrying electricity. The detector tip will light up RED if a voltage is present. The tester can be used to detect voltage from 50 to 1,000 VAC. The tester is a convenient pen size with a fixing clip and easily fits into pockets ready for use. Features:LED detects the presence of AC current.Locate breaks in power cables and wires.Non contact testing for complete safety.Convenient pen size with a pocket clip.2 x 1.5V AAA Alkaline Batteries included. Specification:Voltage Detection: 50V-1,000V ACFrequency: 50-500HzMeasurement: CAT II, 1000VCategory: CAT III, 600V Warning:Always test on a known live circuit before use.This detector is not designed to carry out contact tests on live supplies. Any other form of test should be carried out by a qualified electrician.

GBP 8.99

1

Faithfull VDE Soft Grip Screwdriver Set (Case), 8 Piece FAISDVDESET8

Faithfull VDE Screwdrivers are manufactured to EN 609002004 and individually tested at 10,000V before leaving the factory, guaranteeing a safe working limit of up to 1,000V to provide the maximum level of safety. The screwdrivers feature a two-component, slip-resistant, soft-grip handle with a high quality chrome vanadium steel blade. Each blade is correctly tempered and hardened for high torque and strength. For use on terminal blocks, control cabinets, switches, relays and sockets. Supplied in a durable plastic carry case. This 8 piece set contains the following screwdrivers 1 x Phillips PH1 x 80mm 3 x Pozidriv PZ0 x 60mm, PZ1 x 80mm, and PZ2 x 100mm 3 x Slotted 2.5 x 75mm, 5.5 x 125mm, and 6.5 x 150mm 1 x Mains Tester 100-250V 140mm

GBP 25.99

1

Faithfull Quick Change VDE Screwdriver Set - 13 Piece

The Faithfull 13 Piece Quick Change VDE Screwdriver Set.Faithfull VDE screwdrivers are manufactured to BS EN 60900:2012 and are individually tested at 10, 000V in a water bath before leaving the factory. This guarantees you a safe working limit of up to 1, 000V providing the maximum level of safety.The soft grip auto-lock quick release handle allows the blades to be changed quickly and with a minimum of fuss.Stored in a fabric storage wallet which contains:1 x Auto-Locking, Quick Release Soft Grip Handle4 x Slotted Blades: 0.5 x 3 x 100mm, 0.8 x 4 x 100mm, 1 x 5.5 x 100mm and 1.2 x 6.5 x 100mm2 x Phillips Blades: PH1 x 80mm and PH2 x 100mm2 x Pozidriv Blades: PZ1 x 80mm and PZ2 x 100mm3 x Star Blades: TX10 x 100mm, TX15 x 100mm and TX20 x 100mm1 x Single-Pole Voltage/Mains Tester: 3 x 140mm 100-250V (not VDE certified) Specification:Screwdriver Length (inc. handle) : 190/210mm.

GBP 35.99

1

Faithfull Interchangeable VDE Screwdriver Set, 13 Piece FAISDVDES13I

The Faithfull Interchangeable VDE Screwdriver Set offers a neat solution to the problem of both limited space and portability. Many electricians and service engineers are reluctant to take bulky toolboxes around with them as they are often working in restricted areas or are up and down ladders and need their tools readily to hand. The soft grip handle features an automatic locking system a twist to release function allows the blades to be changed quickly with the minimum of fuss. Faithfull VDE screwdrivers are manufactured to BS EN 609002012 and are individually tested at 10,000V in a water bath before leaving the factory. This guarantees a safe working limit of up to 1,000V providing the maximum level of safety. Supplied in a compact storage case with the following 1 x Auto-Locking, Quick Release Soft Grip Handle. 4 x Slotted Blades 0.5 x 3 x 100mm, 0.8 x 4 x 100mm, 1 x 5.5 x 100mm and 1.2 x 6.5 x 100mm. 2 x Phillips Blades PH1 x 80mm and PH2 x 100mm. 2 x Pozidriv Blades PZ1 x 80mm and PZ2 x 100mm. 3 x Star Blades TX10 x 100mm, TX15 x 100mm and TX20 x 100mm. 1 x Single-Pole Voltage/Mains Tester 3 x 140mm 100-250V (not VDE certified). Specification Screwdriver Length (inc. handle) 190/210mm Storage Case Dimensions 210 x 130 x 44mm

GBP 35.99

1

DIGITAL MARKETING

Brand

Merchant

Price (EUR)