69 results (0,15023 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec QT42410 Ten-Way Charging Unit for QT412

C-Tec QT42410 Ten-Way Charging Unit for QT412

C-Tec QT42410 Ten-Way Charging Unit for QT412The QT42410 ten-way charging unit can simultaneously charge up to ten QT412 Range dual action infraredradio transmitters. Designed to be powered from a 230V a.c. mains source using the standard IEC lead supplied the unit can be wall or desk mounted to suit the transmitter storage and charging requirements of a particular site.Key FeaturesA ten-way plugtop charger designed for use with Quantecs QT412 range of IRRF transmitters.Can simultaneously charge up to ten transmitters.Connects to a standard 13A mains socket using the standard IEC lead suppliedCan be wall or desk mounted to suit the transmitter storagecharging requirements of a particular site.Fully recharged transmitters can be left connected to the charger with no detrimental effect.14-hour typical charging time full cycle.Indicators confirm when charging is complete.

GBP 265.99
1

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor Unit

C-Tec BF391 Isolated Failsafe Monitor UnitAllows IO devices that may not be compatible with the PSUfailure requirements of BS 7273-4 Cat A to comply.Is supplied on a single gang plate with an onboard isolatingEnd of Line Unit EOL and normally energised 24V 3A rated relay.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for all compatible IO units.Provides failsafe operation per BS 7273-4 Cat A B Crequirements for multiple coincidental loop failures sometimes required in aspecification above and beyond the requirements of BS 7273-4 for allcompatible IO units.Key FeaturesAccommodates IO units sited inside or outside the 24V Auxenclosure IO units sited remotely require a BF390 EOL unit to maintain thefailsafe functionProvides complete galvanic isolation between the fire alarmsystem and the door release systemProvides where allowed failsafe manual door releasemonitoring to BS 7273-4 Cat A utilising a single TE cable for multiplemanual operating points such as free swing doors

GBP 26.46
1

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status Unit

C-Tec EP210F Flush Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and ModelMax. 8 remote status units per EP203 panelSurfaceremote status unitsEP210S and weather proof enclosures BF3591 also available

GBP 202.14
1

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status Unit

C-Tec EP210S Surface Remote Status UnitThe remote status unit is designed to connect to the RS485 terminals on an EP203 Automatic Extinguisher Panel toprovide remote system status indicationviaa 128 x 64 pixel LCD status display.Also includes a pull-down manual release button a mode automanual keyswitch and a wide range of system status indicators.Key FeaturesThree monitored input connections Hold Abort and Mode.Max. 8 remote status units per EP203 panel.Flush remote status unitsEP210F and weather proof enclosures BF3591 also available.

GBP 209.29
1

C-Tec BF362 Barrier Interface Unit

C-Tec BF362 Barrier Interface Unit

C-tec BF362 Barrier Interface Unit for Intrinsically Safe DevicesCompatible with all C-TEC manufactured conventional fire alarm panels. Allows a zone of up to 10 intrinsically safe detectors and any number of manual call points to be used in hazardous environments such as gas plants.Key FeaturesOpen and short circuit wiring faults on the hazardous side of the barrier shown as open circuit faults at the fire panelCompatibility Can be connected to any detector Zone circuit on a C-TEC manufactured conventional fire alarm panelPower requirements Aux. 24V operating voltage required from fire panelQuiescent current 2.8mA 30VProduct dimensions mm 55 W x 55 H x D 18mm

GBP 10.79
1

C-Tec QT636 Quantec Interface Unit with Remote Socket

C-Tec QT636 Quantec Interface Unit with Remote Socket

C-Tec QT636 Quantec Interface Unit with Remote SocketAllows any device with a normally open or normally closed 6.35mm 14 inch jack plug to be connected to Quantec. Particularly suited for use with our NC805MD Portable Movement Detector nooperation QT644 Floor Pressure mat nooperationQT633 Bed Exit mat ncoperationor QT634 Chair ExitMat nc operation. Must be wired as a slave to a QT602 or QT609 range addressable call point or QT630 dementia care controller.Key FeaturesWhen thedevice connected to the QT636 is operated a call will be generated on the Quantec call system as programmed.Mounts on a standard UK 25mm single gang back box.

GBP 47.92
1

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920F

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920F

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920FThe NC920EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 222.61
1

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920S

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920S

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920SThe NC920ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 228.82
1

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920F

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920F

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920FThe NC910EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 185.51
1

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920S

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920S

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920SThe NC910ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 191.70
1

C-Tec NC883D Conventional 12V Relay Unit

C-Tec NC883D Conventional 12V Relay Unit

C-Tec NC883D Conventional 12V Relay UnitA general purpose double-pole polarised 12V 5A relay ideal for triggering sirens strobes door releases and other third-party equipmentconnected to an800 Series call system. Can be triggered directly from any of the call systems signal lines provided 12V and -V are supplied to its supply terminals.Key FeaturesTypically used to switch extra low voltagesCan also switch Mains voltages provided the guidelines in the main instructions arefollowedIncorporates a high intensity LED which illuminates red when the relay is activeIncludes a white write on areafor the addition of personalised text such as equipment locations

GBP 42.32
1

C-Tec QT607 Quantec Slave Ceiling Pull Unit

C-Tec QT607 Quantec Slave Ceiling Pull Unit

C-Tec QT607 Quantec Slave Ceiling Pull UnitCan be used to generate a Standard or Ensuite call on aQuantec Addressable Call System. Typically wired as a slave to aQuantec Addressable Call Point or Quantec Accessible Toilet Reset Point. Supplied with 3m of red nylon pull cord and two red open-sided triangular bangles for ease of use by the infirm. Red confidence LED and diffuser emits a bright red glow over a wide area to reassure the user that a call has been made.Key FeaturesSurface mountable.Base fits 16mm conduit and BESA centres.Also available as part of the QT951 Accessible Toilet Expansion Kit.

GBP 21.00
1

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02

C-Tec Moflash EX Red Intrinsically Safe Sounder IS-S-02The IS electronic sounder has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The sounder unit incorporates a Two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesZones 0 1 2 20 21 and 22 ATEX and IECEx approvedIP66 ratedSurface MountPolycarbonate housing material

GBP 151.30
1

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 Way

C-Tec CA737 EACIE 4 Way Flat Interface No PSU In Cabinet Extendable To 8 WayThe C-Tec CA737 is a loop powered 4-8 way flat interface for use on the C-TEC EVAC-ALERT system. It is supplied as a 4-circuit unit extendable to 8 using CA737PCBDetailsA loop-powered 4-8 way flat interface for use on a C-TEC EVAC-ALERT systemSupplied as a 4 circuit unit extendable to 8 using a CA737PCB.Provides 4 or 8 monitored 12.5mA sounder circuits to power up to 2 self-testing evacuation alert sounders per flatIncludes space and connections for an optional fully monitored auxiliary 24V 1A CA737PSU to power additional visual indicators andor vibrating pillow padsIncludes an onboard short circuit loop isolatorUses one loop address per 4 sounder circuitsSounder circuit test facility per circuitThe most practical and flexible device interfacing method for most new and refurb installations the unit is ideally mounted in a riser on each floorMaintains the independent open short circuit monitoring of all sounder circuits

GBP 340.12
1

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring Panel

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring Panel

C-Tec SAP501EX SAP 1 Loop 16 Zone Addressable Sprinkler Monitoring PanelIdeal for monitoring up to 126 sprinkler flow switches.One switch monitoring unit required per monitored flow switch.Utilises the same technology asC-TECspopular XFP addressable fire panel.Up to 16 sprinkler zone indicators availableassignable via the panels PC programming tools.Attractiveflush or surface mountable plastic enclosure.Combined keypad or keyswitch entry.

GBP 455.02
1

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03

C-Tec Moflash EX Intrinsically Safe Beacon with Blue Lens IS-B-02-03This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04

C-Tec Moflash EX Intrinsically Safe Beacon with Green Lens IS-B-02-04This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 172.67
1

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01

C-Tec Moflash EX Intrinsically Safe Beacon with Amber Lens IS-B-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 164.82
1